gates kelly hose supplier

New rubber compounds, higher working pressures and temperatures, stricter environmental and safety regulations – all make hose selection a challenge. At Gates, we make it easy. That’s because our line of high pressure oilfield hoses are made with the demands of today’s drilling methods in mind. From rotary-vibrator drilling hoses to choke and kill hoses, find oilfield hoses built tough to handle the pressure.

Example: "Gates® Black Gold® Rotary Vibrator 3 Inch Max WP 7500 PSI API SPEC 7K Tested To 15000 PSI Grade E FSL 1 Temp Range 1 ISO 14693 License 7K-0003 Made In U.S.A."

High-pressure hydraulic oil lines. Exceeds ISO 18752 Grade B, SAE 100R17 and ISO 11237 R17 working pressure, minimum bend radius requirements and performance requirements of EN 857 1SC. M3K hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose.

465711574M3KXREEL, 7048570485 4M3KXREEL072053318623Automotive Hydraulics -> Hydraulic Hose -> Global M3K Mega3000 Hose - SAE 100R17Hydraulics -> Hydraulic Hose -> Global M3K Mega3000 Hose - SAE 100R17

ISO 9001:2000 certified custom manufacturer of abrasion, oil & weather resistant reinforced hose with tubes, covers & fittings for rotary drilling & exploration work. Hose are available in various models with specifications including 2 1/2 in. to 5 in. ID, 3.06 in. to 8.90 in. OD, 5 ft. to 100 ft. length, 2500 psi to 7500 psi rated working pressure, 48 in. to 72 in. minimum bend radius, 3 in. to 6 in. API thread, 2 in. to 3 in. NPT thread, minus 40 degrees F to plus 200 degrees F operating temperature & 3.9 lbs. to 43.6 lbs. weight/ft.

Flexible drilling rubber hoses play an important role in petroleum extraction. They should suffer high operating pressure, extreme operating temperature, abrasion and other inferior elements. Our special compounded synthetic rubber has been proven an effective and economical way to reject these problems. All our oilfield drill hoses are manufactured as API 7K or other related specifications.

Steel cable reinforcement loads most working pressure up to 15,000psi. The wires are usually zinc-plating or copper platting to improve steel wire resistant against rust and corrosion. Due to the thick reinforcement, the hoses should be handled or stored in correct way to avoid kicking or crushing. They will substantially decrease their rated operating pressure.

Rotary hose, Kelly hose, cement hose, mud hose, jumper hose and vibrator hose and choke & kill hoses are the most popular oilfield rubber hoses. They convey high-pressure drilling fluid from one place to another. Many end fittings are provided to satisfy different applications. Most end fittings are made according to API standards. Special order is also available.

The power braided slim hole rotary reinforced hose swaged and coupled with FIG H2S Hammer head Union connections on both the ends. The mating Male/Female Hammer head Union complete assembly parts to be included in the supply.

A more economical alternative to our polyurethane layflat hose. Warflex is reinforced with high–tenacity polyester yarn and coated through the weave with a 70% nitrile rubber / 30% PVC blend for good chemical resistance for produced water. Less abrasion resistance and puncture resistance. Custom hose color and branding available on big volume orders.

The new Midwest Hose Layflat Deployer completes our extensive water transfer portfolio. Our Direct Drive System makes our deployer one of the fastest, most powerful, and easy to use on the market with the capacity to deploy and retreive layflat hose up to 16″ in diameter.

Ideally suited for any high pressure hydraulic applications where there is a need for hoses to be Fire Rated and capable of working in extreme heat in the event of an emergency.

Hoses have a higher working pressure than normally available chemical hoses. CPE handles a wide variety of acids, alcohols, salt solutions, and petroleum based products.

Lightweight chemical transfer hose designed for almost every common industrial chemical used in industry today (98% of chemicals) without staining / contamination.

Designed for applications that required the hose to slide easily or require visual confirmation of material flow. Great for pumping water and light chemical solutions. Popular with pumping equipment because it handles suction discharge uses.

Lightweight, flexible, rugged suction/discharge hose that has good chemical resistance. Excellent for transferring fertilizer solutions, septic solutions, and pesticides. Hose remains flexible in sub-zero temperatures. Helix serves as a scuff strip.

Economical general service suction and discharge hose used for pumping water and light chemical solutions. PVC helix increases flexibility and abrasion resistance while the smooth interior provides maximum flow.

Designed for water discharge in construction, heavy duty equipment rental, and mines and quarries. Soft-wall hose construction provides similar performance to a layflat hose but a higher working pressure and more abrasion resistance.

Mud discharge hose designed for petroleum waste, drilling mud, diesel, and water. The standard to transfer liquid mud at high pressures from the mud pump.

Designed for use with push-on fittings for air tools, petroleum products, gasoline, mild chemicals or water. No clamps or special tools required. Hose reinforcement laid at the most effective angle for maximum strength and coupling holding ability.

Wire braid steam hose for saturated and superheated steam up to 250 PSI 450° F. Cover is pin pricked to allow venting to eliminate blistering and cover separation.

General purpose hoses for open end discharge. Non-absorbing, mildew proof, and rolls up flat for easy storage and handling. Common in construction, agriculture, irrigation, marine, and rental applications. PVC hoses resistant to oils, grease.

Designed to handle edible liquids, vegetable oils, salad dressings, vinegar, mustard and meat products requiring a sanitary hose which will not impair taste. Great for service with hot oil fat filters and fryers.

Designed as a hydraulic brake hose for vehicles and motorcycles. The average life of a brake hose is six years. Brake hoses swell with age and restrict flow. Generally all brake hoses on a vehicle deteriorate at the same rate.

Air Brake Tubing, Steel Brake Line Tubing Assemblies, Steel Brake Line Tubing Coils, Rubber Air Brake Hose, Silicone Coolant Hose, Silicone Heater Hose, GPR Radiator Hose, Rubber Heater Hose, Garage Exhaust Hose, Air Conditioning Hose

Camlocks, Petroleum Handling, Industrial and Oilfield Hose Ends, External Swage Hose Ends (Holedale), Crowsfeet Couplings, Sand Blast Couplings, Ground Joint Couplings, Bauer Style Quick Connects, Ringlock Fittings, Storz, Foot Valves and Strainers, Airline Accessories, Industrial Accessories, Clamps, Pressure Washer, Safety and Protection Products

Available in sizes 1/4″ – 12″. Operates in high/low temperatures. Fire safety up to 1200° F. No permeation of gases. Full vacuum. Annular is hydroformed, a process that enhances flexibility and extends the life of the hose. Suitable for oils, chemicals, gases, exhaust gases, water, steam, vacuum.

Plug Valves, Swivel Joints, J-55 and N-80 Pup Joints, Integral Fittings, Steel Hose Loops, Crossover Adapters and Swages, Blast Joints, Manifolds, Bull Plugs and Caps

37° JIC, Pipe, Pipe Swivel, O-Ring Kits, O-Ring, Split Flange, Face Seal, Hose Barb, Flareless Bite Type, Metric, BSPP, BSPT, Inline Live Swivel, 90° Live Swivels, 90° Dual Plane Live Swivels, Test Points, Thread ID Kits

Inverted Flare, SAE 45° Flare, Compression, Self Aligned, Polyline Flareless, Push-Connect, Push-Connect Air Brake, Compression for DOT, Compression for Air Brake Copper Tubing, Threaded Sleeve, Pipe Fittings, Needle Valves, Drain Cocks, Truck Valves, Ground Plugs, Multiple Shut-Offs, Hose Barbs, Push-On Hose Barbs, Garden Hose Fittings

The high pressure hoses are a bonded construction comprising steel and elastomeric materials. The principal characteristic of bonded construction is the build-up of individual layers in the flexible hose wall which are then combined into one unit through vulcanisation. Hose assemblies are manufactured as a single bonded unit to specified lengths where the couplings are a chemically bonded integral part of the hose.

Protects the polymer lining from mechanical damage, prevents blistering in case of high pressure gas service and decompression with vacuum service, supports the wall of the flexible hose. This layer is optional and present only for rough bore hoses, such as for flexible choke & kill lines with TauroFlon™ liner.

Fluid barrier of the flexible line. Protects the hose construction from corrosive and abrasive effects of the conveyed medium. The thickness of lining depends on the internal pressure, the inside diameter and the conveyed medium. The lining material is selected to withstand chemical and heat effects of drilling mud, well effluents, cement slurry, hydraulic fluid or whatever substance is conveyed through the hose.

Drilling hose(rotary hose)made according to API 7K spec, applies for flexible hose connection between the top of oil drilling stand pipe and vertical moved swivel joint in well drilling, well cementing, work-over and down-hole servicing operation. drilling hose is also used to adjust the installation mistake between drilling pipe line and stand pipe to avoid shake, sometimes to transfer high pressure oil and water base mud with the lowest aniline point of 60°C from the swivel pipe in high pressure, and down-hole operation high medium such as water, oil etc, drilling rotary hose can be used for prefect work too.