mud agitator design in stock

Derrick mud agitators include an explosion-proof, “C” faced motor, reduction gearbox (helical-bevel gears for horizontal agitators or all helical gears for vertical units), impeller, and shaft with assembly bushings. Motors range from 5 to 30 HP and may be supplied in several power configurations.

Attaching the motor directly to the gearbox protects correct alignment that can increase bearing life and provides 95 percent efficiency in power transfer to the impeller. Using this superior design surpasses standard worm drive gear assemblies by 30 percent, allowing Derrick agitators to do the same work at far less horsepower. By unitizing the motor and gearbox, weight and space requirements are reduced. Horsepower, mechanical configuration, impeller diameter, and shaft length are customized to tank dimensions and maximum mud weights. Available horsepower ratings* are: 5, 7.5, 10, 15, 20, 25, and 30.

As Mud Agitator Manufacturer, Brightway can supply BWJBQ 5.5-22kw Mud Agitator for mud tank and mud system. including: Horizontal Mud Agitator or Vertical Mud Agitator. Brightway mud agitator can be customized once we get the detailed requirements. Buying mud agitator from Brightway will be your best choice for drilling mud circulation system.

1. Brightway mud agitator equips with a motor couple to a rugged oilfield gearbox, which can eliminates troublesome couplings, misalignment and have a longer bearing life. And it is driven by the explosion-proof motor, coupled to a gearbox which will drive the impeller shaft. Due to the simplex turbine structure of shaft,

2. Brightway mud agitator is featured by compact construction, light weight, balanced transmission, small footprint, low noise and high efficiency. And its impeller turbines can transform the mechanical power into drilling fluid agitation as well as circulation.

3. Brightway mud agitator can be designed per customer’s requirement to choose the helical-bevel design or worm design for reduction gearbox. Its motor can be horizontal or vertical. As for the shaft and impeller, compared with painting process, the galvanizing treatment is usually adopted to create a better anti-rust performance.

Also of highest value in these equations, the future demands for stand-by-capacity for Recovered Oil is very challenging. The PG-Submix agitators may be used to keep the water-emulsion-heavy oil mixed, in suspension – hence pumpable when at discharge, which will reduce discharge time and turn-around of the vessels significantly.

Needless to say: these are perfect match for PG-MACS, which allow all cargo tanks to carry Recovered Oil – which could easily allow a PSV 4500 to carry in excess of 2.000m3, if designed properly. A fleet of such vessels would eliminate the need of many OSRV’s, and save a lot of money in chartering.

The skid mounted MA-RG agitator is compact, and its low profile reduces headroom requirements and provides more layout space on top of the tanks. The gearbox is a triple-reduction helical-bevel gear drive system that reduces the rotational speed of the motor to drive the impeller(s). Up to 95% mechanical efficiency helps reduce horsepower requirements.

Impellers are available with flat blades (radial flow), contour blades (axial flow), and canted blades (radial/axial flow). The impellers are sized according to tank volume and expected duty. Active mud system compartments—such as solids removal sections, mud mixing sections, and slug pits, which need a higher shear force to produce immediate mixing—are another consideration in impeller sizing.

HJBL series vertical mud agitator is mainly used for deep mixing and mixing in the mixing tank. The mixing shaft is longer than 1 meter and equipped with a stainless steel base to ensure that the mixer runs stably and does not shake during the mixing process.

Vertical mud agitator can be widely used in chemical industry (fine chemicals, pharmaceutical chemicals and daily chemicals), environmental protection (sewage treatment), pharmaceuticals, cosmetics, metallurgy, food, heat treatment cooling, leather processing and other industries.

2. Reliable: the steel frame is equipped with a high-quality brand geared motor with excellent performance, and the specific anti-corrosion material or anti-corrosion surface treatment is designed and used according to the actual working conditions;

Mud agitator is an important part of the drilling-fluid solids controling system. Drilling fluids agitatorcan be installed on drilling fluid tank, with the impeller submerged into certain depth under fluid surface to stir the fluid directly.During this process, the drilling fluid can be mixed even, and the solid particles are eliminated.In this way, it can improve solid phase dispersion, and increase the viscosity and gel strength, thus to make drilling fluid keep accordant with the requirement, provide needful fluid for drilling process, and ensure the smooth going of drilling work.Drilling mud agitator is the same as mud agitator.

TR solid control provide vertical and horizontal agitator. Horizontal mud agitator is divided into coupling type and direct type agitator. If you need a horizontal mud agitator, we recommend you use a direct type agitator. drilling mud Agitator is an ideal device for stirring, mixing liquid and preventing the solid-phase precipitation in the mixture.

Drilling Fluids Agitator in the mud system used to,mixing ratio and prevent to the mud tanked.TR solid control is an exporter of centrifugal pump . We are an exporter of drilling fluids mud agitator.Our factory approval the ISO9001,drilling agitator have the API certification.TR solids control is the designed,selling,production,service and delivery of Chinese mud agitator manufacturer. We will provide the high quality drilling fluids agitator and best service.Your best drilling mud tank agitators start from TR solids control.

For contour impeller applications, values must be significantly faster (i.e., smaller numbers) to achieve the same results, but because of the impeller design, air entrainment is less probable. In symmetrical compartments, the fluid has a nearly equal distance to travel from the center of the impeller shaft or from the impeller blade tip before it contacts the vessel wall. Agitators should be placed where the shaft is centered in the tank or compartment.

For contour impeller applications, values must be significantly faster (i.e., smaller numbers) to achieve the same results, but because of the impeller design, air entrainment is less probable. In symmetrical compartments, the fluid has a nearly equal distance to travel from the center of the impeller shaft or from the impeller blade tip before it contacts the vessel wall. Agitators should be placed where the shaft is centered in the tank or compartment.

The Technostrength Mud Agitator combines compact design with high torque performance levels necessary for a uniformly suspended flow of drilled solids throughout the mud systems.

Powered by 1500RPM (4 pole) explosion proof motor and connected through heavy duty gear reducer, this agitator transfers high torque at RPM toread more...

Mud agitator, also called drilling mud agitator, used for drilling fluid agitation mix, prevent drilling fluid solid particles in the tank circulation system deposit, cycle drilling fluid performance stability, mixed evenly. Mud agitator composed by explosion-proof motor, reducer, engine base and impeller components four parts.read more...

Used for rapid and uniform incorporation of dry and liquid ingredients.Creates a deep vortex, exposing dry ingredients directly into the agitator blades. This is a standard agitator for bakery applications.Ideal for soluble, dry ingredients that want to float on the surface.

Mud agitator, also called drilling mud agitator, used for drilling fluid agitation mix, prevent drilling fluid solid particles in the tank circulation system deposit, cycle drilling fluid performance stability, mixed evenly. Mud agitator composed by explosion-proof motor, reducer, engine base and impeller components four parts.read more...

- Lightweight, but sturdy construction with the highest torque rating in the industry. Example: 15 hp KOE Agitator weighs 246.4 kg compared to industry averageread more...

GAURAV ASSOCIATES manufacture the GAMA range of Mud Agitators. These Mud Agitators are used for agitating mud slurry for obtaining consistency through proper blending in flow controlled applications.

We are providing to our clients superior quality Mud Agitators. Our offered Mud Agitators are widely appreciated by our clients which are situated all round the nation. These Mud Agitators are used for agitating mud slurry for obtaining consistency through proper blending in flow controlled applications.

A mud agitator is mainly used to agitate and mix the drilling mud to prevent solid particles from depositing in the tank. For proper mixing the mud agitator must be properly sized with respect to power requirement and impeller size.

Flow simulation (CFD) can be used to predict the rate of deposition in a tank. In many cases CFD is convenient for purposes of preliminary assessment, when the only opportunity to perform physical test is after the agitator is already installed in the field. Simulation can also be used efficiently to optimize with respect to engine power and impeller design.

The most accurate approach is to model the deposition in the tank as time passes. This is called a transient simulation. However, transient simulationis are very time consuming. A faster approach is to assume steady-state condition of the circulating fluid. For mud agitators this is usually a very good approximation to assume that the flow is not changing with time.

GN Solids Controlis a world famous turnkey provider of solids control equipmentfor oil and gas drilling fluids. GN Solids Control has rich experience on design, development, and manufacture solids control equipment includes but not limited to shale shaker and shaker screen, decanter centrifuge, desander, desilter, mud cleaner, mud agitator, cuttings dryer, centrifugal pump, screw conveyor and mud tank etc.

Last month, GN Solids Control finished manufacturing of one batch mud agitators for one offshore drilling rig platform. Consider the heavy duty mud, GN Solids Control provides helical bevel gerabox reducer for these mud agitators.

GN Solids Control manufactures mud agitator with single impeller, double impellers or multiple impellers. The shaft length of the mud agitator is customized based on customer’s mud tank depth.

GN mud agitator keeps the drilling mud from sediment, and plays a very important role in mud mixing, preparing and storage. GN Solids Control also provides control boxes to match the mud agitators, explosion proof includes IEC Ex, ATEX, CNEX etc.

In order to use in the offshore platform, GN Solids Control use PPG painting to cover the mud agitators with 3 layers which can keep sea moisture rusty from long time usage.

Besides the mud agitators, GN Solids Control has also been providing the other types of solids control equipment like decanter centrifuges and shale shakers for offshore drilling platforms. GN Solids Control made DNV lifting certified equipment is able to move safely and conveniently, the DNV lifting pad and supporting frame can be added optionally.

Now GN Solids Control has many solids control equipment in stock, once we received the order, we can just buy the motors and put the control boxes, tested and get it to delivery very fast. Welcome to connect with GN Solids Control for any drilling mud solids control and drilling waste management equipment inquiries.