southwest mud pump module for sale

Premium"s high-strength, triple reduction, forged steel triplex fluid end modules are made from 4130 alloy steel, heat treated for a long working life, machined to perfection and packaged for delivery with anti-corrosion protection. The precision-made jewelry, like the exterior finish, reflects the superior quality inside.

The market demand for 7500 psi land drilling has continued to increase and forecasted to remain strong as drillers and operators seek to complete wells more faster and more efficiently. Premium has the expertise and ability to convert existing 5000 psi pump systems with our 7500 psi fluid end upgrade. In addition to replacing the existing valve-over-valve module with our proven L-Shaped design, a typical conversion also includes an upgraded liner retainer system, discharge cross/ strainer, high-pressure discharge manifold and 7500 psi pulsation dampener.

Direct replacement for the current 7500 psi wide body module (same outside dimensions and same external and internal components except valve cover, bore seal and Falcon spring retainer)

BOMCO/Emsco Mud Pumps:F2200HL, F1600HL, F-1300, F-1600, FB1300, FB1600, F-800, F-1000, F-500, F-350, DB-550, DA-700, FA-1600/1300, FC-2200, D-300/500, D-375, D-700,

The L-shaped two-piece fluid-end was adopted into the market over 35 years ago because it was an obvious improvement over one-piece modules. Since the suction module is separate from the discharge module, it is possible to replace the suction module when it wears out instead of replacing the entire fluid end.

Southwest’s L-shaped fluid-end is manufactured from heat-treated 4130 forgings and equipped with our quick-change valve cover system; our L-shaped modules offer unmatched performance.

The market demand for 7500 psi land drilling has continued to increase and is forecasted to remain strong as drillers and operators seek to complete wells more faster and more efficiently. Southwest Oilfield Products has the expertise and ability to convert existing 5000 psi pump systems with our 7500 psi fluid end upgrade. In addition to replacing the existing valve-over-valve module with our proven L-Shaped design, a typical conversion also includes an upgraded liner retainer system, discharge cross/ strainer, and high-pressure discharge Mud Pump with Southwest L-Shaped Fluid End Modulesmanifold and 7500 psi pulsation dampener.

Updated performance data sheets that reflect the higher working pressures are provided for all upgrades performed by Southwest Oilfield Products. To ensure pump operation integrity, rod load limitations are strictly adhered to.

Facing the fiercely competitive market, we take "honesty, truth-seeking, innovation and service-oriented" as our corporate tenet, and through scientific management, we have become a leader in the API Tubing Dp Casing Elevator, driling Electrical Submersible Pump, driling Cryogenic Liquid Tank industry. Our company has an elite team with excellent technology and unity. From product development to shipment, we strictly control every link to make customers satisfied. We actively introduce foreign advanced technology and continuously improve and perfect our products. We abide by the promise to customers and the ethical standards, and we won"t harm the interests of the customers. When you are keen on any of our goods following you view our product list, be sure to feel free to make contact with us for inquiries.

We supply fluid end expendables, which could be interchangeable with international reputed mud pump brand. Like EMSCO, Gardner Denver, National, Ideco and etc.

We always adhere to the core concept of "integrity, pragmatism, and excellence", stick to the business policy of "quality first, service first", and constantly improve innovation capabilities, striving to produce Southwest Mud Pump Spare Parts Fluid End Module that satisfy customers! Our company has always been leading science and technology first, pioneering and innovative business philosophy, attaches importance to product development and innovation. With a team of experienced and knowledgeable personnel, our market covers many countries worldwide.

Manufacturer of mud pump systems and premium well servicing equipment. The company designs and produces mud pump products which include fluid end modules, pistons, liners, and other related products used during onshore and offshore drilling of oil and gas wells to major drilling companies across the globe. It"s servicing equipment division focuses on the manufacturing of new equipment used in well completion, stimulation, and intervention such as frac pumpers, coil tubing, nitrogen and snubbing units.

MUD PUMP PERFORMANCE CHART PUMP MAX MAX STROKE LINER SIZE IN INCHES MODEL I.H.P. S.P.M. LENGTH 4 4 1/2 5 5¼ 5½ 5¾ 6 6¼ 6½ 6¾ 7 7 1/4 7 1/2 MAX-P.S.I. 5000 5000 5000 5000 4714 4313 3960 3650 3380 3130 2910 2713 2535 12”A-1700-PT 1700 150 G.P.R. 1.96 2.48 3.06 3.37 3.70 4.05 4.41 4.78 5.17 5.11 6.00 6.43 6.88 G.P.M. @ 150 R.P.M. 294 372 459 506 555 608 662 717 776 767 900 965 1032 MAX-P.S.I. 5000 5000 5000 5000 4714 4313 3960 3650 3380 3130 2910 2713 2535 10”A-1400-PT 1400 150 G.P.R. 1.63 2.07 2.55 2.81 3.09 3.37 3.67 3.98 4.31 4.65 5.00 5.36 5.74 G.P.M. @ 150 R.P.M. 245 311 383 422 464 506 551 597 647 698 750 804 861

BASED ON 100% VOLUMETRIC EFFICIENCY AND 90% MECHANICAL EFFICIENCY FLUID END TYPE MODEL OF PUMP SIZE OF PUMP OEM 5000 PSI OILWELL A-1700-PT / A-1400-PT 7-1/2” X 12” / 10”

ITEM QTY. NO. PART NO. DESCRIPTION REQ’D 1 1388YXX LINER REFER TO GUIDE TO ORDERING CHART ON PG. 6 FOR TYPE (G); (Y); AND FOR BORE SIZE (XX) 3 2 2974-XX LINER GASKET (REFER TO GUIDE TO ORDERING CHART FOR TYPE AND SIZE (XX) 3 3 8488-4 WEARPLATE 3 4 2974-1 WEARPLATE GASKET (ALSO AVAILABLE IN URETHANE P# 2974-1U) 3 5 XX-BYY PISTON (REFER TO GUIDE TO ORDERING CHART FOR SIZE (XX) AND FOR TYPE (YY) 3 5A 2932 PISTON BUSHING (FROM 1-5/8” TO 1-1/2” STRAIGHT BORE) 3 6 568-225 PISTON SEAL 3 7 1290HW-25 PISTON ROD (WITH 1 ½-8 ELASTIC STOP NUT) 3 8 API-4ESN PISTON ROD NUT 3 9 1290W2 PISTON ROD CONNECTING STUD (WITH WATER HOLE) 3 10 1290HW1 SUB ROD 3 11 1290CW ROD CLAMP (WITH WATER JACKET) 3 11A 1200H30 HOSE (1/2” X 30” WITH 1/2” MALE X 3/8” MALE CONNECTIONS) 3 11B 1200120 PIPE (3/8” X 12” GALVANIZED AND THREADED ON ONE END) 3 11C 4018-94 BOLT (5/8-11 GRADE 8 BOLT WITH LOCK NUT AND WASHER) 6 12 1200G90 PONY ROD 3 13 SEE PAGE VALVE COMPLETE 6 14 SEE PAGE VALVE INSERT 6 15 SEE PAGE VALVE SPRING 6 16 SEE PAGE VALVE SEAT 6 SWTM1700 HYDRAULIC SEAT PULLER KIT COMPLETE (REFER TO TOOLS SECTION IN CATALOG) 1 4475-3A SOUTHWEST HP QUICK-CHANGE VALVE COVER ASSEMBLY: (QTY PER ASSY CONSISTS OF ITEMS 17-24) 17 4475 VALVE COVER FLANGE 1 18 4575 SCREW GLAND 1 19 4675-3A PLUG (COMPLETE WITH VALVE GUIDE; BUSHING; AND SCREWS) INCLUDES ITEMS 21, 22, & 23 1 20 P129 HP VALVE COVER PLUG NITRILE SEAL (ALSO AVAILABLE IN URETHANE SEAL USE P# P129U) 1 21 4775-3R VALVE GUIDE (COMPLETE WITH BUSHING #4700I) 1 22 4700I VALVE GUIDE BUSHING (ALSO AVAILABLE IN URETHANE P# 4700IU) 1 23 4016-99 VALVE GUIDE SCREW 2 24 4015-2 VALVE COVER STUD (WITH SW PART# HHN1250-7 1 ¼-7 HEAVY HEX NUT) 12 OILWELL VALVE COVER ASSEMBLY: (QTY PER ASSY CONSISTS OF ITEMS 22, AND ITEMS 25-28) 25 80500003 VALVE COVER 1 FLUID END TYPE MODEL OF PUMP SIZE OF PUMP OEM 5000 PSI OILWELL A-1700-PT / A-1400-PT 7-1/2” X 12” / 10”

ITEM QTY. NO. PART NO. DESCRIPTION REQ’D 26 80400003 VALVE GUIDE 1 27 80432236 VALVE GUIDE CAPSCREW 2 28 AJO229R VALVE COVER GASKET 1 29 4016-76 POWER END STUD (WITH SW PART# HHN1750-8 1 ¾-8 HEAVY HEX NUT) 12 30 80381003 LINER ADAPTER SLEEVE (STEEL) (ALSO AVAILABLE IN BRONZE PART# 80381003B) 3 31 6588-4 LINER ADAPTER NUT 3 31A 80067236 LINER ADAPTER SET SCREW 9 32 4018-70 SUCTION MANIFOLD CAPSCREW (WITH LOCKWASHER) 24 33 8588-50A SUCTION MANIFOLD 1 34 80102003 SUCTION MANIFOLD GASKET 3 35 8488-51D DISCHARGE MODULE 1 36 8488-52S SUCTION MODULE 1 37 8388A DISCHARGE MANIFOLD 1 38 568-345 DISCHARGE MANIFOLD GASKET 3 39 4017-2 DISCHARGE MANIFOLD STUD (WITH SW PART# HHN1375-8 1 3/8-8 HEAVY HEX NUT) 12 40 9070017 PONY ROD SEAL 41 9060023 PONY ROD BAFFLE

NOTE: DUAL-DURO® AND GRAYLOY® ARE REGISTERED TRADEMARKS OF SOUTHWEST® OILFIELD PRODUCTS. VALVES & SEATS (OEM OILWELL A-1700-PT/ A-1400-PT) STAINLESS PULLER HEAD TYPE VALVE INSERT SPRING SEAT PULLER HEAD SPRING STYLE SOUTHWEST (Full Open) 777-8B N/A 941 N/A 877-7 SWTM4250 SPLIT JAW SWTM40-SN SPLIT JAW FULL OPEN-ROUGHNECK SWND-7V2 N/A SW5710-115L N/A SWND-7S1 SWND-7PH PANCAKE FULL OPEN-ROUGHNECK SWTM40-SN SPLIT JAW SWND-7V2H N/A SW5710-115L N/A SWND-7S1 (High Temp) SWND-7PH PANCAKE FULL OPEN-ROUGHNECK SWTM40-SN SPLIT JAW SWND-7V1 SWND-7I SW5710-115L N/A SWND-7S1 (w/Replaceable Urethane Insert) SWND-7PH PANCAKE3 WEB DOUBLE ANGLE O-RING SWR0500110 SWR0514275 SWR0513744 SWR0514790 SWR0509309 SWTM3-7T 3 WEB (High Temp) SWR0520502 SWR0520501 SWR0513744 SWR0514790 SWR0509309 SWTM3-7T 3 J HOOK 3 WEB STANDARD PLATE SWR0505062 SWR0504893 SWR0513937 SWR0514423 SWR0509309 SWTM3-7T 4 WEB SWU5C-EEF SWUDD-7B SW5710-110 N/A SW7DD-B1 SWTM4-7 4 J HOOK 4 WEB (High Temp) SWU5C-EEFHT SWUDD-7BHT SW5710-110 N/A SW7DD-B1 SWTM4-7

14 P-220 Mud Pumps 3 available completely overhauled. The pumps have been machine inspected and all data will be provided. These 2200 HP pumps complete with Southwest fluid end modules which have been reworked and pressure tested by Southwest and P-QUIP liner retention systems. The drives can be set up for AC or DC power. All Master Rig equipment meets or exceeds O.E.M. standards and a complete data pack is furnished with purchase. Please call if you have any questions.

READY TO SHIP - Three (3) completely refurbished 1600 HP Continental Emsco 7500 PSI Mud Pump Packages - liner spray system, suction manifold and dampener, discharge strainer cross, reset relief valve, 20 gallon pulsation dampener, 75 HP charge pump, two (2) GE 752 1000 HP rear mounted motors, 10 HP blower, mounted on a 3 runner skid with loading hitches and much more. Units come with complete data books and have been tested. MRI is a API facility and units comply with API standards.

Duplex mud pump package completely refurbished and never operated. Tri-Services Manufacturing TSM-500 pump, CAT engine. Data book provided with complete refurbishment details.

Manufactured to withstand the toughest drilling and environmental conditions, our K-Series triplex mud pumps are ideal for all drilling applications. This legacy product features a balanced forged-steel crankshaft and Southwest Oilfield Products ‘L” Shaped modules which is essential to minimize wear, noise, and operating vibrations. These attributes are essential when drilling deeper high pressure formations, long laterals and when handling corrosive or abrasive fluids and slurries.

Every American Block triplex mud pump is manufactured and fully load tested before leaving our manufacturing campus, and is available in sizes ranging from 800 HP to 2200 HP. The American Block K1600 HP Mud Pump is also available in a 2000 HP up-grade version, when more HP is needed in the same 1600 HP footprint.

Southwest # 6390G06, 6390G07, 6390G08, 6390G09, 6390G1, 6390G2, 6390G3, 6390G4, 6390G5, 6390G6, 6390G7, 6390G8, 6390G9, 6390ZIR1, 6390ZIR3, 6390ZIR5, 6390ZIR7, 6390ZIR9 w/liner gasket AJO428S in rubber and AJO428SU in urethane

API 7K Premium Bimetal liners have high strength forged steel hulls machined to fit prospective pumps and machined to provide the sleeve retaining lip for the high pressures encountered in today"s markets. All our liners have centrifugally cast high chrome sleeves with added Molybdenum for a deeper hardness. The sleeves are mounted in the hull to a tightness averaging 18 thousands tight. After the hull and sleeve are assembled, the I.D. of the liner is honed to a perfect circle and to a finish that is smoother than any of our competitors. The finished and honed liner has tapered ends for ease of assembling pistons into the liner. The tapers are consistently the same. We have improved the overall finish (surface) of our products to a point that the looks are as impressive as the built-in quality. Our plant takes extensive measures to insure the quality of the products