zirconia mud pump liners pricelist

Titan Oil Tools offers high quality mud pump expendables and mud pump replacement parts for the wide variety of mud pumps, centrifugal pumps found on the world market today. These quality pump parts offer great performance and our pricing will save you money.

We are your oilfield supplier of choice for mud pump spares and mud pump parts: mud pump piston liners and pistons. All mud pump parts can be sourced for fast delivery; Come to us for mud pump liners, pistons, piston rods and parts, pony rods, threaded rings and caps,and more. Try us for duplex and triples pump spares and duplex and triplex mud pump parts, and also valve parts like valve seats. gland nut, and mud pump gaskets.

Mud pump liners may come in chrome, alumina ceramic and zirconia ceramic. Chrome liners and alumina ceramic liners are less costly, their cost of replacement over one year as the chart below shows, is much more than zirconia ceramic liners.

The table below shows a Mud Pump Liner Cost of Ownership which shows a reasonable cost comparison for a rig in continuous service for 36 months. This of course does not include the high cost of maintenance downtime and the cost of labor.

The prices below are based on cost/cylinder. Savings increase when you add up the number of pump cylinders on your rigs and extend the savings to understand the big difference it can make for your budget.

FLUID END EXPENDABLE PUMP PARTSBaker SPD62DOUBLE ANGLE O-RING VALVEThe Double Angle O-ring Valve is made with a tough one-piece body to run more hours between change outs. It"s made withcarburized premium alloy steel to resist wear, provide a positive seal, and help protect against wash out or damage to the pump.FEATURESSpecified for all drilling operations up to and exceeding 5,000 psi Maximum operating temperature is 170F Patented polyurethane insert is noted for its Double Angle 55seal contact surface, which maintains cylinder priming during pump shutdown Sizes fit most mud pumps Shelf life of polyurethane insert is maximum of 5 years Body is a one-piece design, configured to give maximum containment of the insert with minimum use of materialDOUBLE ANGLE O-RING BLUE STREAK HIGH TEMPERATURE VALVEThe High Temperature Double Angle O-ring Valve body is a one-piece design, configured to give maximum containment of the insert with minimum use of material. The valve and insert configuration has been operated at pressures up to and exceeding 5,000 psi. FEATURESMaximum operating temperature is 200FShelf life of polyurethane insert is maximum of 5 yearsSTANDARD PLATE TYPE VALVEThe Standard Plate Type Valve is extremely durable to its premium forged alloy steel body and its unique design. It has been proven by more than 50 years of oilfield service. To prevent dry pistons and liners at startup, the valve features a patented double angle polyurethane insert that maintains cylinder priming during pump shut-down. The precise control of insert pre-load is accomplished with a flat ground insert retaining plate and split retainers. The insert can be replaced in the field with minimum down time. This valve is designed to fit pumps in the oilfield and is used with Baker SPD seats. FEATURESSpecified for all drilling operation up to and exceeding3,500 psiMaximum temperature rating for the standard polyurethane insert is 170FMaximum temperature rating for the Buna-N rubber insert is225FAvailable with Buna-N rubber or polyurethane insertsShelf life of polyurethane insert is maximum of 5 yearsShelf life of Buna-N rubber is maximum of 10 yearsValves with rubber lipless inserts are rated for pressure up to2,500 psiNote: Baker SPD Double Angle O-ring and Standard Plate Type Valves do not interchange with any other manufacturer.Double Angle O-ring Seat, Spring, and ValveDouble Angle O-ring Seat, Spring, and High Temperature ValveStandard Plate Type Seat, Spring, and ValveVALVES AND SEATS 2007 SPD. All rights reserved.4302 Prot, San Antonio, Texas 78219, Tel 1-800-688-5650 or (210)-304-5650, Fax (210) 304-5641Triplex Pump PistonsSPD provides a wide variety of pistons for mud pump appli-cations, including bonded, urethane, rubber, and replaceable rubber or urethane inserts.SPDs bonded urethane pistons are designed for resistance to extrusions and abrasions. With water cooling, these pis-tons will provide optimum performance in oil base mud and high drilling pressures. Bonded urethane pistons are rated for drilling opera-tions up to and exceeding 5,000 psi Urethane pistons provide extended service life under high pressure The Blue Streak

High Temperature Bonded Urethane Triplex PistonTriplex BondedRubber PistonFor more information on liners and other products, please visit us at www.ForumSPD.com or email sales@ForumSPD.com.Zirconia Ceramic Liners HP Design with shoulder on hull to prevent sleeve slippage SPD ID tolerances is +.010/-.000 - Industry allowance is +.015/-.000 Surface nish 4 8 RMS - Chrome sleeved liner nish 16 20 RMS Expected run life exceeding 10,000 hours Hardness: HV 0.3 kg/mm - 1100/1200 (92 94 Rc) (Chrome sleeved liners are 60 64 Rc) Ceramic liners do not create ID ridges which are common in high chrome liners. ID ridges are a cause of piston failures. Ceramic liners improve piston run life. Ceramic liners are pressure rated to pump performance by piston size. Liners are available in sizes 4-1/2 to 7. Liners are available for popular pumps: EMSCO: FC-2200, FB-1300/1600, F-800/1000 Gardner Denver: PX-11, PZ-10/11, PZ-8/9 National: 14-P-200/220, 12-P-160, 10-P-130 Oilwell: A1400/1700PT Wirth: TPK-2200, TPK-1600/2000 Liners for other pump models and liner sizes available upon request.For more information on liners and other products, please visit us at www.ForumSPD.com or email sales@ForumSPD.com. You can also contact us by calling 1-800-688-5650. Zirconia Sleeved Liners for Mud Pumps in Drilling Applications Basic description of Zirconium Oxide/Zirconia: Zirconia engineered ceramic parts can be formed by single axis pressing, isostatic pressing, injection molding, slip casting, or extrusion. Parts can "green machined" to near net size before firing and then "hard" ground using diamond tooling to tolerances less than 0.0002" (0.005 mm). Special grades of zirconia can be enhanced with additives to create a multiphase material and also metallized creating an option to be brazed to metal parts. Applications: Although there are a number of uses for Zirconia, the application of a Zirconia sleeve for a mud pump liner is gaining increasing attention. Although other materials have been used for mud pump liners such as high chromed sleeves and Aluminum Oxide sleeves, Zirconia is gaining favor in this application. A Zirconia sleeve is much harder than a chrome sleeve and therefore offers longer life. Although Ziconia is softer than Alumina, it is not as brittle and therefore will survive low impact shock loading and moderately rough handling. The run life of these two ceramic materials is very close, however because of the careful handling required by Alumina sleeved liners to prevent cracking damage, Zirconia liners are preferred. The Multiphase compound process results in a much smaller grain size which is one of the factors to improve wear life. Properties of Zirconia PSZ MS Grade and Zirconia Multiphase Properties Units Test Temp. Zirconia MS Grade Zirconia Multiphase Density G/cm3 20qC 5.74 5.6-5.7 Flexural Strength MPa 20qC 725 650-800 Tensile Strength MPa 20qC 450 - Weibull Modulus m 20qC >30 >25 Compressive Strength MPa 20qC 1990 1900 Modulus of Elasticity GPa 20qC 205 210-220 Poissons Ratio 20qC 0.31 0.31 Hardness HV0.3 kg/mm2 20qC 1120 1100-1200 Fracture Toughness MPam 20qC 8-12 11-14 Average Grain Size Pm - 40 0.35 - 2 Thermal Conductivity W/m-K 20qC 3.08 2.5 Thermal Expansion Coefficient X 10-6/C 20-400qC 10.2 9.1 Specific Heat J/g-K 20qC 0.47 0.40 Operational Characteristics: Standard chrome sleeve liners wear at a rate of about .007" to .010" on the diameter per 100 hours under normal conditions. When a liner reaches about .070" over nominal diameter the engagement with the piston reduces to a point that blow by begins, resulting in piston failure. The liner wears like a barrel on the ID resulting in the maximum wear at the center of the stroke. The ends of the liner will be at the original nominal diameter. Ceramic sleeve liner will wear in the same way as chrome liners but at a rate of about .001" or less per 100 hours. This rate of wear will result in potential life of 10,000 or more hours. Of course there are a number of variables which would shorten or even lengthen the run time. Recent tests conducted with KCA Duetag and Nabors Drilling have confirmed that wear of only .020 or less have occurred in 4000 hours. Projection of this wear rate would indicate a life of 14,000 hours or more. Urethane pistons are recommended for use with ceramic liners. Piston life in a ceramic liner is variable. The initial piston normally will only run about 200 hours or less. During the initial run the piston further smoothes the liner ID. Subsequent pistons have been known to run much longer up to 500 or 600 hours. However, as the liner becomes worn, the piston lip will begin to loose interference with the liner ID, reducing run life. The above noted run times are dependent on operating conditions. Typical conditions are pressure to 3800 psi, stroke rate to 90 spm, temperature below 170 degrees F, clean mud with weights of 11 to 14 lbs. and a high volume water flush to the back of the piston is required. Higher pressures, stroke rates and temperatures will increase the wear rate.

Our enhancement depends around the sophisticated devices ,exceptional talents and repeatedly strengthened technology forces for Ceramic Plunger Mud Pump, Pvc Glove Hand Mould, Polished Surface Zirconia Ceramic Plunger, Ceramic Cutter Blade,Honeycornb Ceramics. Please don"t hesitate to contact us if you are interested in our products. We firmly believe our products will make you satisfied. The product will supply to all over the world, such as Europe, America, Australia,Munich, Montreal,Sudan, Ireland.Based on products and solutions with high quality, competitive price, and our full range service, we have accumulated experienced strength and experience, and we"ve built up a very good reputation in the field. Along with the continuous development, we commit ourselves not only to the Chinese domestic business but also the international market. May you moved by our high quality items and passionate service. Let"s open a new chapter of mutual benefit and double win.

The ceramic liner is the best choice for high pressure mud pumps. It is manufactured strictly in accordance with specific technical standards by use of advanced processing techniques. The ceramic liner comes in various specifications, which come in Φ150～180×310～440mm.

Chrome-Iron Liners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Zirconia-Ceramic Liners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mud-Pump Gear Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Main material we have is alumina (al2o3) lined pipe, silicon carbide (sic) and zta lined pipe. 1. mateial: alumina zirconia and zta. 2. size: max diameter 500mm, max length 1000mm, 3. tolerance. Tolerance can be as tight as +-0.01mm, surface roughness can be ra 0.2um. advantages of our lined pipe. 1. Excellent wear resistance. 2. very fast delivery. 3. very competitive prices.

Main material we have is alumina (al2o3) lined pipe, silicon carbide (sic) and zta lined pipe. 1. mateial: alumina zirconia and zta. 2. size: max diameter 500mm, max length 1000mm, 3. tolerance. Tolerance can be as tight as +-0.01mm, surface roughness can be ra 0.2um. advantages of our lined pipe. 1. Excellent wear resistance. 2. very fast delivery. 3. very competitive prices.

The zirconium ceramic liners can not only adapted to some tough environment such as deep oil reservoir, hard stratum and severe earthiness, but also can be used for offshore oil and natural gas exploitation as well. So ceramic liners are the first choice to upgrade high pressure mud pump liners.