12 gauge overshot card punch free sample

Place an overshot card on top of the shot charge just before crimping to improve overall crimp quality and seal in small shot and/or buffer. Excellent for use with BPI Roll Crimpers.

Our testing lab has proven that poor crimps can alter the performance of an otherwise good load. Overshot cards always produce better, more consistent crimps and this consistency is demonstrated in the standard deviation of loads in our lab. Our ballistic lab recommends overshot cards for better crimps in all loads.

Clear Overshot Disks(either plain or printed with shot size) are also offered for great roll crimping options. See pictures in Additional Images or click on this link.

Shotshell size selection: Use the same size gauge as your hull. Smaller diameter cards also work if your particular size is out of stock. For example, a 20ga overshot card works in a 16-gauge shotshell and so on.

While reloading shot shells and using roll crimps, overshot cards are placed on top of the shot/buffer media to keep everything in the shell. ...Why buy them when you can print them for about 2 cents each?

This is an overshot/wad card cutting die. Insert this die upside down inside your press using a L-N-L bushing adapter. I"ve made provisions for adding a metal washer or other insert to beef up the cutting area. Reem the metal insert to 18.67mm.

This one is an overshot waterwheel, printed as a flat pack then glued together. ...I have included 2 versions of the paddles a single piece on and a 3 piece on that can be printed flat

This one is an overshot waterwheel, printed as a flat pack then glued together. ...I have included 2 versions of the paddles a single piece on and a 3 piece on that can be printed flat

Overshot water wheels In an overshot water wheel the mill race brings the water to the top of the wheel, where it strikes the paddles or buckets and turns the wheel. This is more efficient because as well as the force of the flowing water, the...

12g (12 gauge) Template for cutting out Overshot Cards for Shotgun Rollcrimp Shot Shells If you like my models please consider supporting me on Patreon : https://www.patreon.com/bigmrtong

Friend wanted to know if I could make business cards for him. After some trial and error this what he got. ...Of corse scaled down to .3 so it will be about the size of your palm.

http://www.thingiverse.com/apps/customizer/run?thing_id=66327 Instructions Using the following options: bottom_text_rotation = 0 Move_Image_Left_Right = 30 card_type = 56 top_text_rotation = 0 build_plate_selector = 3 bottom_text_label =...

Sometimes what you do can"t be put on a business card. Maybe you design custom Oilfield Software for fluid management. Maybe you are a photographer or graphic design artist. Perhaps you write code or film porn. Any way it goes a few samples of your...

Wanted a case for business cards. ...Prints quickly on mk MK2s. Fusion 360. I suggest you slightly size the top up a hair so its a snugger fit. 85mmx55mm business card.

http://www.thingiverse.com/apps/customizer/run?thing_id=66327 Instructions Using the following options: Move_Bottom_Text_Up_Down = 43 build_plate_manual_y = 100 build_plate_manual_x = 100 card_type = 71.1 Move_Image_Up_Down = 40 card_count = 40...

Summary Sometimes what you do can"t be put on a business card. Maybe you design custom Oilfield Software for fluid management. Maybe you are a photographer or graphic design artist. Perhaps you write code or film porn. Any way it goes a few samples...

Sometimes what you do can"t be put on a business card. Maybe you design custom Oilfield Software for fluid management. Maybe you are a photographer or graphic design artist. Perhaps you write code or film porn. Any way it goes a few samples of your...

The tool consists of two components including a punch, and die. Starting with the punch, it’s made from hardened tool steel designed to maintain a sharp cutting edge. If you’re the kind of reloader who loads tens of thousands of shells, you’ll be pleased to know the tip has been bored out and extra material left in place so that it can be re-sharpened easily should the need arise. The base of the punch is designed to fit a Lee Precision, single stage press, however it should fit any brand with sufficient clearance that’s compatible with Lee shell holders.

To install this tool, the operator begins by slotting the punch into place and raising the ram. This step helps ensure everything’s lined up well when installing the die, to avoid damaging the cutting edge during operation.

The operator begins by lowering the ram part way until the punch is just below the feed port on the die, but still inside the base of the die.  All reloading presses have a bit of play in the shell holder, so the safest way to protect the cutting edge is to simply feed the punch into the die part way before engaging the cutting edge on material.

Next, the user simply slides the material to be punched into the feed port and begins operating the press as normal.  As filler wads are punched, they will be pushed out the top of the die where they can be collected.  If the operator’s intention is to produce a great many filler wads in one sitting, it is advisable to place a container (a margarine container works well) with a hole cut in the bottom on top of the die, allowing them to stack up inside and avoid making a mess.

Originally designed this unit to punch corrugated cardboard, so that seems like a good place to begin.  The punch works quite well with standard corrugated cardboard boxes I’ve cut into strips.  It’s a fast, simple process that yields nice, concentric disks.  Cardboard works great for buck and birdshot as it’s dense enough to take up slack, but flexible enough to compress during loading.  This is critical to obtaining a professional looking crimp with even the trickiest loads.

Next up is craft foam.  It’s not really my first choice due to it not being biodegradable, but I know some folks really like it, so I have confirmed the punch will work with it.  As with the cardboard and cork, it punches very easily, although the edges aren’t quite as smooth as the denser materials.

Finally we have plastic blister packaging.  Although not biodegradable, I really like having a transparent option on hand when I need something as an overshot card.  Once again it cuts smoothly, and easily.  The material demonstrated above is  actually plastic from grocery store salad containers if you can believe it, however thicker packaging not only punches well, it crimps even better.

The finished filler wads measure 0.650″, the same internal diameter as a standard 12G shot cup, and an equally excellent size for use as overshot cards.  With a good supply of these on hand, it’s no trouble at all to customize my shot columns by placing them above or below my shot or slugs.  Likewise, if I’ve got a difficult load to crimp like low-volume birdshot or roundball slugs, adding one to the top as an overshot card makes things a snap.