l-80 n-80 pup joint supplier

These J55, L80, N80Q & P110 pup joints are manufactured from seamless Grade J-55, L80 N80Q and P110 mechanical tubing. The API 5CT tubing pup joint is mainly used to adjust the height of the tubing strings. It is also used to adjust the depth of down-hole tools.

China J55, K55, N80, L80, P110 Pup Joint Factory Dervos Supplies J55, K55, N80, L80, P110 Pup Joint, 2 3/8 to 20IN, Length 0.61m, 0.91m, 1.22m, 1.83m.

China J55, K55, N80, L80, P110 Pup Joint Factory Dervos Supplies J55, K55, N80, L80, P110 Pup Joint, 2 3/8 to 20IN, Length 0.61m, 0.91m, 1.22m, 1.83m.

The pup joint is a commonly utilized fitting in industrial pipe connection. According to various connections, it can be normally divided into thread and flange types. The threaded type can be further categorized into two head external thread, single head external thread, and flat head external thread types. In addition, the item falls under tubing and casing types based upon various usages.

Compared with the tubing, it is simply different in length. We can produce a variety of flat end and external upset tubing pup joints with J, N, L, and other steel grades and different specifications.

Driveshafts are built to transmit power across rotating shafts, even when placed under stress. The driveshaft connects the front and rear axles. It resembles a large metal rod with a circular cross-section to which other components are attached to form a complete assembly. Axle shaft assemblies and drive shafts are used to couple a transmission with either an axle or another component such as a differential on four-wheel-drive vehicles. There are various types of wholesale n80 pup joint available for cars, trucks, vans, and more!

Custom driveshafts can be selected and personalized using an assembly that consists of a journal, shaft, bearings, and U-joints all working together. It is important to match the components with the correct specification as per size, type and load applied. Front driveshafts add an aggressive look to vehicles and improve traction under hard acceleration by eliminating the torque reaction. These front driveshafts are made with equal length shafting and universal joints for a great fit without modifications. Rear driveshafts are also important for the vehicle transmission system. They transfer the power produced by the engine to the rear axle assembly with the least amount of friction and heat buildup. Universal driveshafts are used for SUVs, trucks, and other large trucks that have a long wheelbase. These driveshafts are relatively expensive but worth the investment.

Carbon-fiber driveshafts provide a very light yet strong replacement for conventional steel or aluminum shafts. Carbon fiber is a unique material whose strength and stiffness can be tailored to meet specific engineering requirements. That"s not it! We have more wholesale n80 pup joint including driveshaft replacement parts, aluminum driveshafts, 2-piece driveshafts, and truck driveshafts.

Pipe system involves various components, including l80 tubing pup joint and are made from different materials. We offer wholesale l80 tubing pup joint to create a smooth channel for the pipe systems in both commercial and residential areas.

BLAZE is adequately equipped to supply NPST Pup joints made of high quality seamless pipeline with  male & female detachable hammer union. NPST has uniform bore for greater flow capacity. NPST pup joints are available in 2″ to 4″ sizes, length for pup joint range from 1 feet to 20 feet at 15000 psi. Pup joint with Non- pressure seal thread union (NPST) are especially engineered for high pressure, abrasive services where welded connections are not desired. The design provides a strong, permanent end connection without butt welding. An epoxy thread-locking compound secures the connection.

Casing or Tubing Pup Joints, Casing or Tubing Connectors and Casing or Tubing Couplings. In addition it is capable of Threading items at Groups 1, 2, 3 & 4 of API spec. 5CT. Items supplied by BLAZE meet the Quality Standards as defined in API 5CT assuring

BLAZE is also well equipped to supply Line Pipe Couplings/ NPST pup joints with wide range of specifications. In addition we can supply thread Line Pipes and its accessories of various sizes. Items meet the quality standards as laid down in API – 5L.

Our supplier partners include producing mills in every continent of the globe, and we proudly represent them to distribute OCTG tubing, casing, couplings, pup joints, and line pipe in the demanding US and Canadian oil and gas markets, as well as in all Latin America region.

We are one of the prominent Suppliers and Exporters of Tubing Pup Joints in UAE. Tubing pup joints produced according to API 5CT Specification. Our precision-engineered tubing pup Joints are ideal for spacing out down-hole assemblies and handling the production of tubing accessories. We supply tubing pup joints in all sizes and grades. All our products have passed the ISO certification and API certifications.

We are highly appreciated among our clients for providing the best quality tubing pup joints and other oilfield equipment. Our products are tested numerous times under technical guidance and are made from the best quality material. Standard and non–standard sizes are available as per customer requirements.

ll pump joints are made from modified alloy steel heat-treated to a Brinell Hardness range of 285–341 with a Charpy V-Notch minimum impact strength of 40 ft-lbs at 70°F guaranteed to one inch below the surface Connections can be cold rolled after machining, if requested All connections are phos-coated to prevent galling during initial make-up

API Spec 5CT – This Standard specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material and establishes requirements for three Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for PSL-1 are the basis of this Standard. The requirements that define different levels of standard technical requirements for PSL-2 and PSL-3, for all Grades except H-40, L-80 9Cr and C110, are contained in Annex H.

We care about your needs, we pay attention to the quality of Steel Pipe Seamless Nipple & Pup Joint; Oil OCTG Casing & Tubing Pup Joint Oilfield Services J55/K55/N80/L80/P110/C95/T95/80s, your satisfaction is our eternal pursuit, quality and integrity is our goal. We strictly and seriously fulfill our contracts, keep our promises and strengthen our network system of after-sales service. We set up a sense of quality service and do our best to do the entrusted project of each contracted customer.

One is a short Drill Pipe used to adjust the length of the Drill String; The other one OCTG Pup Joint is a pipe of non-standard length, which is used to adjust the length of tubular strings to its exact requirement.

Vigor can manufacture the Tubing Pup Joints by different technology - Upsetting and Machining process. if you have a special requirement on the Pup Joint production process, please just specify.

If you are looking for a competitive, high quality and fast delivery oilfield pup joint in stock, or if you are planning to buy pup joint API from one of the leading casing and tubing pup joint manufacturers, API 5CT pup joint in stock, l8013cr pup joint, nue/nue tubing pup joint manufacturers and suppliers China, please feel free to contact VIGOR.Details  of  API  Spec.  5CT  Oil  Tubing  Pup  Joint

We are a Supplier and Exporter of Casing Pup joints in UAE. It"s mainly used to adjust the height of the casing strings. Our casing pup joints are made under the API 5CT specifications. These product features are high corrosion resistance or long running life.

We supply casing pup joints in all sizes, grades, and thread profiles to meet custom requirements. All our products have passed the ISO certification and API certifications. Our products are tested numerous times under technical guidance and are made from the best quality material. It is also used to balance the depth of down-hole tools.

Pup joint is kind of pipe without non-standard length to adjust the length of tubular strings to its exact requirement. API casing and tubing pup joint are produced according to API SPEC 5CT standard. Beyond the standard of oil casing pipe is called pup joint, the main oil casing pup joint material: J55, K55, N80, L80, C90, T95 and P110. Anson steel is a professional pup joint manufacturers in the steel line with good reputation.

TIANJIN DALIPU OIL COUNTRY TUBULAR GOODS CO.,LTD is a modern professional industry and trade combined enterprise specializing in producing and trading pipes in oil field.The main products of our company are the oil casings and oil pipe lines. Our products have casing pipe,tubing pipe,casing and tubing coupling,pup joint,line pipe,crossover,flange,protect caps and so on.We not only supply our goods with many large oil fields, but also establish a long-term business relationship with the Middle East Europe, Africa and other countries around the world and co-operative very well.

Casing pup joint is mainly used to adjust the height of the casing strings. It is also used to adjust the depth of down-hole tools. Our pup joints are manufactured in accordance with the API Spec5CT specification. The steel grades of the products of this kind are J55, K55, N80 and L80 P110. These products feature high corrosion resistance and long running life. As a pup joints supplier, we also produce the API 5CT tubing pup joint which is the fitting of the tubing strings. And we promise that all our casing pup joints are in high quantity.

Casing pup joint is mainly used to adjust the height of the casing strings. It is also used to adjust the depth of down-hole tools. Our pup joints are manufactured in accordance with the API...

A pup joint is Casing, Pipe or Tubing shorter in length than a standard tubular string. This allows for the adjustment and installation of tools and various tubular components when placement downhole is critical for a specific project. A Spacer Pipe is another reference used to identify pup joints. Pup joint features consist of connections, lengths, weights and material grade.

Crossover pup joints are manufactured from seamless mechanical tube. As with all Crossover products, each piece is marked with a distinctive job number and heat number that is fully traceable. A complete range of sizes (1" to 4.5"), weights (standard or heavy wall), and grades (J-55, N-80, L-80, and P-110) are commonly available from stock in 2", 3", 4", 6", 10", and 12" lengths. Lengths up to 20" are available upon request.