hv4 rotary table supplier

This little beauty is from a world class factory! It features 3 3/8 inch t-slots for fastening the work to the table and is constructed of high density Meehanite casting. It is inspected by the HEIDENHAIN process and is guaranteed flat and parallel. Gear ratio is 90 to 1 and the worm is hardened and ground. The table is graduated a full 360 degrees and the micro adjust collar is graduated in steps of 1 minute. Vernier scale makes settings down to 10 seconds achievable. MT-2 center hole. We do offer tail stocks and dividing plates for these units as well. Unit is 3.11 inches high.

A wide variety of hv rotary tables options are available to you, such as manufacturing plant, machinery repair shops and energy & mining.You can also choose from 1 year, 6 months and 1.5 years hv rotary tables,As well as from not available, {2}, and {3}. and whether hv rotary tables is bearing, gear, or motor.

One of the main points to consider when selecting a rotary table is to go as big as you can within the limits of the milling machine that you want to use the table with. I have a small 3″ table that I have used with my Unimat Mill and with the larger Mini Mill, but it is rather small and very limited in capacity and stiffness.

The thumb screw on the main body can be released and then the worm rotated to disengage from the gear thus allowing the table to rotate freely, this allows the to be rotated by hand to a given position.

The 2 table clamps lock the table and stop rotation – they are a tad clunky and caphead bolts would be better than the bars. The issue is the bolts are 6×1.25mm which is a very odd and rare thread.

The back of the table with the bolts that attach the back plate, again there is no play in the main table bearing in any direction. The image to the right shows me fitting a locking bolt to hold the ER25 collet chuck in place.

It was only after 6 months that I went to set the table up as a dividing head that I realised I had been sent 3 dividing plates, 2 of which were identical – an email to Warco and the missing dividing plate arrived 2 days later along with a free return address for one of the doubles that I had. Read more about gear cutting with the HV4 rotary table.

This calculation is available for free in a Workshop Calculations spreadsheet. That allows you to change the inputs for your own rotary table/head and division plates.

A solid 4″ rotary table that is actually nearly 4.5″ (110mm) and with a very sturdy worm drive. There are some oddities such as 6×1.25mm threads used for the locking nuts and the locking of the worm drive.

Aligning the rotary table – a simple method to align the rotary table centre with the mill spindle and then to align a part on the table and clamp it down. This is rather rough and ready approach, but it works to a degree. I’ve then gone on to try a number of different methods and then measured the accuracy using a dial indicator.

Gear Cutting with the Warco HV4 Rotary Table – I’ve now used this table with the indexing plates a number of times and the results are superb. This is a very easy to use table that is simple to setup with the plates and easy to again turn back to a normal rotary table.

Our main Product line range includes Lathe"s Quick Change Tool Posts, Lathe Parting & Turning Tool Holders, Rotary Tables & Its accessories Like Clamp Kits, Dividing plates, Tailstocks, ER Collets Adaptors & Small Chucks with Back Plates, Knurling Tools, Lathe Alignment Test Bars, Vee Blocks, Revolving Centers, Vertical Milling Slides, Boring Heads, Fly Cutters, Arbors, Sleeves, Precision Vises For Milling, Drilling & Grinding, Bench Vises, HSS Lathe Form Tools & Carbide Brazed Tools Set, Lathe Chucks, Angle Plates, Surface Inspection Plates, Various DIY Hand tools, Punches, Jwelry Tools, Indexale Tools & many more.....