indexing head vs rotary table for sale

Rotary tables are mounted horizontally, and most can also be mounted vertically. In both cases only at 90° to the mill table. A Dividing Head is always vertical, but can be tilted through 90°.

Dividing heads are always fitted with "indexing plates" (holed wheels and clock hands), allowing a wide range of angles to be turned. The indexing mechanism can do intermediate angles. Rotary tables can be fitted with indexing plates as an accessory, but usually the number of angles supported is limited compared to a dividing head. (A generalisation. And, because rotary tables do all common angles, the limitation may not matter.)

Rotary tables are more convenient for general work because most jobs are mounted at 90° or 180° relative to the milling table. Possibly more robust than a dividing head for rough work. When close accuracy isn"t needed, jobs can be spun rapidly by the rotary table without cranking the handle - a time saver. When accuracy is needed the handle and worm are engaged. Usually there"s a vernier scale sufficiently accurate for most work. The handle is also relatively fast because most simple angles can be produced with it. For example, easy to crank from 0, 60, 120, 180, 240, 300, 0 to cut a hexagon head. Unfortunately not all angles are "simple"!

Indexing plates are useful for awkward angles. Cutting a 19 toothed gear requires 19 steps of 18.9474°, which is the hard to remember sequence 37.89, 56.84, 75.78, 94.74, 113.68, 132.63° etc. The Index plate and clock hand mechanism remove the need for the operator to track the sequence but they are still a pain to use in my opinion!

Indexing plates are so awkward that driving a Rotary Table with a stepper motor and microcontroller is popular. You simply tell the controller how many divisions are needed, press "Go", and the computer does the rest. Apart from reducing brain strain and automating a tedious task, the computer eliminates most mistakes. Computers don"t get sums wrong, have excellent memories, and are hard to distract! Also, a computer and stepper motor will do a good job of angles too complicated for the Indexing plates.

Generalising again, I suggest most people, most of the time, only need a rotary table. I see Dividing Heads as specialist tools and have never felt the need for one. For the same reason I drive an ordinary small car rather than a Land Rover. The closest I get to off-road driving is a supermarket car park! You might live on a farm...

Unless there"s a specific reason for needing a Dividing Head, I wouldn"t spend money on one. My rotary table is used a lot, in contrast a Dividing Head is only "nice to have".

Rotary Tables└ Workholding Supplies└ Workholding & Toolholding└ CNC, Metalworking & Manufacturing└ Business & IndustrialAll CategoriesAntiquesArtBabyBooks & MagazinesBusiness & IndustrialCameras & PhotoCell Phones & AccessoriesClothing, Shoes & AccessoriesCoins & Paper MoneyCollectiblesComputers/Tablets & NetworkingConsumer ElectronicsCraftsDolls & BearsMovies & TVEntertainment MemorabiliaGift Cards & CouponsHealth & BeautyHome & GardenJewelry & WatchesMusicMusical Instruments & GearPet SuppliesPottery & GlassReal EstateSpecialty ServicesSporting GoodsSports Mem, Cards & Fan ShopStampsTickets & ExperiencesToys & HobbiesTravelVideo Games & ConsolesEverything Else

Rotary Tables└ Workholding Supplies└ Workholding & Toolholding└ CNC, Metalworking & Manufacturing└ Business & IndustrialAll CategoriesAntiquesArtBabyBooks & MagazinesBusiness & IndustrialCameras & PhotoCell Phones & AccessoriesClothing, Shoes & AccessoriesCoins & Paper MoneyCollectiblesComputers/Tablets & NetworkingConsumer ElectronicsCraftsDolls & BearsMovies & TVEntertainment MemorabiliaGift Cards & CouponsHealth & BeautyHome & GardenJewelry & WatchesMusicMusical Instruments & GearPet SuppliesPottery & GlassReal EstateSpecialty ServicesSporting GoodsSports Mem, Cards & Fan ShopStampsTickets & ExperiencesToys & HobbiesTravelVideo Games & ConsolesEverything Else

Dividing heads allow you to divide a circle into equal fractions conveniently. Anything that involves regular action around a circle is a candidate for a dividing head.

A rotary table has no stops so it is not convenient to do large numbers of things at equal intervals because you would have to painstakingly determine the interval. Also, the rotary table does not divide the circle. For example, if you were making 13 equally spaced operations using a rotary table you would have to calculate some wierd angle for each operation and dial it in--a tedious process. For example, here are the 13 angles for a circle division:

Do you want to manually set each of these values? Have fun doing that. Now, imagine doing it for 53 divisions. You will be there all night. Not only that, the error will be a lot more than a dividing head.

I have used it in the vertical position to cut a 107 tooth gear which isn"t covered by any of the dividing head wheels I"ve got. I set up an excel spreadsheet with the angle required for each tooth which isn"t as easy as it sounds as the rotary table is calibrated in degrees/minutes/seconds rather than decimal degrees so it took a bit of figuring out how to do it.

An indexing head is intended for making EVEN rotary divisions of any desired number, is generally smaller and usually has the dividing plates as a basic part of the head. It also generally uses a chuck or collet to hold parts although faceplates can be fitted to them. Thus, an indexing head is ideal for making things with evenly spaced divisions, like gear teeth, hole circles, N sided bodies, etc. It is not very good if different spacings are needed, but they can be done. Also, it is generally good for smaller parts but larger ones can be accommodated.

A rotary table has a faceplate built in and is generally larger than an indexer. But both come in all sizes so this is far from absolute. And you can mount chucks or collet closers on them, it is just a bit harder to do. They may or may not come with dividing plates for ease in making any arbitrary number of even divisions, but they usually have accurate markings in degrees, minutes, and seconds. Due to these absolute scales, it is easier to make odd angles between features. They will mount larger work on their faceplates and it is easier to make circular arc cuts when milling on a RT than it would be on an indexer. Many of them do come with dividing plates and virtually all of them can have them added if that is desired. Another thing that is normally made on a RT is a spiral: this requires external gearing or CNC control.

Each of them can do all of the above. It is just EASIER to do some of these things on an indexer and others on a RT. I have a 10" RT as my first purchase and have not regretted that choice. I got a bargain so I took advantage of that. However, an indexer would have also been a good first choice if a similar bargain would have been possible there. In the end, I will probably get both. I also plan to make some dividing plates for my RT when I have time as they do make the job of doing even divisions a lot easier. For now, I just use a table of angular settings and hope I do not make any mistakes.

Reversible clamp, 4th axis, rotary table, rotary dividing table, controlled rotary table, dividing attachment, dividing head, rotary indexing table rotary coupling

Precision rotary table tiltable type UT300, precision rotary table can be used horizontally and vertically, for milling, drilling, grinding and marking work.

1 pair of prismatic blocks without clamping brackets, suitable for clamping round material, prismatic incision 90°, made of special cast iron, supplied in pairs

Universal dividing head, HOMGE, type BS-2, incl. tailstock, flange and 3 dividing discs, as milling machine accessories for direct and indirect dividing.

Clamping tables, swivelling ±45 degrees in both directions, with rotating plate rotatable through 360°, type HAP, with reinforced construction in special cast iron.

Precision rotary tables HOMGE type HHV, universal dividing head for milling, drilling, boring, grinding and marking work, for horizontal and vertical use.

Semi universal dividing head ZENTRA, type HUT, with indexing plate with 24 holes for direct dividing, including tailstock, flange and 2 dividing plates.

ZENTRA precision rotary table RT with a gear ratio of 90:1 / for milling, drilling, boring, grinding and marking work is horizontally and vertically versatile.

Precision rotary table dividing head ZENTRA type RT-DF, mounted lathe chuck for milling, drilling, boring, grinding, scribing work, for horizontal and vertical use.

Direct dividing attachment Zentra TA, for direct dividing including three-jaw lathe chuck and indexing disks as milling machine accessories ✅ order now!

Zentra dividing head with handwheel and three-jaw lathe chuck, clamping disk and indexing plates, for horizontal / vertical use as milling machine accessories.

ZENTRA indexing disks for precision rotary tables type TS for the production of precise, indirect graduations as for example in gear milling ✅ buy now!

Universal dividing head ZENTRA VUT-200KPL, incl. lathe chuck, tailstock, turning and drilling jaws and 2 dividing discs, for direct and indirect dividing.

Universal dividing head, ZENTRA, type VUT-2A, incl. tailstock, flange and 2 dividing discs as milling machine accessories for direct and indirect dividing.