stanley hydraulic pump parts manufacturer

The TP03 and TP08 lines of trash pumps are a great example of the power of hydraulics when it comes to pumping liquids with solids. The TP03 pump provides 450 gallons per minute (1688 lpm) of discharge capacity and can pump solids up to 3 inch (76 mm) in diameter. The TP08 has a 800 gpm (3028 lpm) of discharge capacityand can pump up to 4 inch (102 mm) diameter solids.

A division of Stanley Black & Decker, STANLEY Infrastructure is the world’s largest handheld hydraulic tool manufacturer and a worldwide market leader, offering over 150 handheld hydraulic tools and over 30 mounted impact tools.

Stanley detwatering pumps, the pure power of hydraulic tools is also exemplified in our trash pumps. Our TP03 pump discharges an impressive 450 gallons per minute (1688 lpm) and can handle up to 3 inch (76 mm) diameter solids. Our TP08 discharges 800 gpm (3028 lpm) and can handle up to 4 inch (102 mm) solids.

The SM50 water pump is fitted with dripless flat-faced HTMA quick couplers for easy connecting and disconnecting of the pump and hydraulic system. The water outlet is a 3-inch pipe thread fitted with a 3-inch groove fitting to which can be connected a cam hose end fitting. Access to the pumping chamber for cleaning requires the removal of only two cap screws. The motor with the impeller attached is then easily removed from the pump casing. The SM50 can draw down water to a depth of 3.5 inches. Putting the SM50 in a sump will allow it to pump all but 3.5 inches of water remaining in the sump. The integral screen effectively keeps solids larger than 3/8 of an inch out of the pump. The pump will handle clear water and water containing up to 10% solids.

Stanley Hydraulic Tools has a proud tradition of being a global leader in the development of a wide range of innovative hydraulic products used in a variety of industries and applications throughout the world. A division of Stanley Black & Decker, Stanley Infrastructure is the world’s largest handheld hydraulic tool manufacturer and a worldwide market leader, offering over 150 handheld hydraulic tools and over 30 mounted impact tools. Browse our full Stanley Hydraulic Tools catalog below.

EC Hopkins offer the complete range of submersible pumps and trash pumps from Stanley hydraulic tools. All of these products offer amazing performance for their size and weight.

The range includes three submersible pumps and two trash pumps. Benefits include, high volume output, self-priming, no suction hose, can be run dry without damage, maintenance free wear resistant parts, small and light weight with a high power to weight ratio. The pumps can handle solids of various sizes suspended in liquids, model dependant.

The trash pumps can pump a range of materials including water, sand and slurries, gravel, sludge and solids up to 4” in diameter. The TP03 and TP08 trash pumps are successfully sold into a wide range of applications, Utility, flood, disaster relief, USAR, agriculture, subsea and treasure hunting are just a few of these applications.

Stanley hydraulic pumps is submersible and exemplify the pure power of hydraulic tools. The SM50 pump discharges an impressive 500 gallons per minute (1890 lpm) while it"s small size allows it to fit in a box 11 inches deep by 10 inches square (26.7 cm x 25.4 cm).

The motor drives the impeller directly, so there are no spindle bearings that requires periodical lubricant or replacement. The cast stainless steel, semi-closed impeller resists corrosion. A series of seals on the drive shaft effectively keep fluid and pumped water where they belong while allowing the pump to be run dry without sudden seal failure.

The Stanley TP03 Submersible Trash Pump boasts 450 gpm of output flow, this pump is an efficient way to move large volumes of liquid with concentrations of solids up to 25% by volume. The TP03 handles solids up to 3 inches in size and is used for dredging and light cleaning tasks. The urethane bowl and impeller is abrasion resistant, resilient and impervious to petrochemical solvents. No priming necessary, just drop it into the material and it’s ready for work.

The urethane bowl is virtually indestructible - tough, lightweight, abrasion resistant, resilient and impervious to petrochemical solvents. The Stanley TP03 can pump almost anything without damaging the bowl.

The Stanley TP03 Submersible Trash Pump’s efficient design places the urethane impeller above material flow, reducing blockage, jamming and overall pump wear while keeping liquids moving fast enough to pump high volumes of solids at a much higher head than non-submersible pumps.

Note:In an effort to improve portability and ease of use, modifications have been made to all TP03 and TP08 model trash pumps. For both pumps a quick link clip (p/n 73577) and carrying handle (p/n 73576) were added and connected to the eyelet located on the top plate. The rounded handle allows for increased comfort while carrying when compared to the previous square handle. With the clip feature, the handle can be removed to allow for large crane hooks to attach to the eyelet. In addition, the color of the TP03 urethane bowl has been changed from black to yellow. This change was made to increase pump visibility while operating in murkier substances or liquids.

The Stanley TP08 Heavy Duty Trash Pump is used for dewatering, dredging, cleaning and as a effective bilge pump. The gear motor is direct drive to the cast iron impeller with easy access for clean out of the fabricated steel volute.

The Stanley TP08 Heavy Duty Trash Pump has been designed to get the most from an HTMA Type II hydraulic circuit. Using only 9 gpm/34 lpm of hydraulic flow, the TP08 will pump over 800 gpm/3,028 lpm at a 10 ft/2.54 m head. The free-flow impeller and 4 in./ 100 mm inlet and outlet combine to make the TP08 one of the most efficient pumps in the business.

Weighing only 59 lbs/27 kg and with its convenient handle, the Stanley TP08 Heavy Duty Trash Pump can easily be handled by one operator. The Stanley TP08 Heavy Duty Trash Pump and the Stanley HP1 Compact Power Unit make a powerful, portable team for high volume de-watering and trash pump applications.

The heavy-duty construction of the Stanley TP08 Heavy Duty Trash Pump features a fabricated, all steel volute and abrasion resistant cast iron impeller. The volute uses replaceable UHMW polyethylene wear plates to reduce wear and extend pump life. The heavy-duty Stanley HYREVZ™ hydraulic motor is self-lubricating.

Routine maintenance for the Stanley TP08 Heavy Duty Trash Pump is easy. The top cover is attached to the volute with six wing nuts so cleaning and inspection can be accomplished in just a few minutes.

Note:In an effort to improve portability and ease of use, modifications have been made to all TP03 and TP08 model trash pumps. For both pumps a quick link clip (p/n 73577) and carrying handle (p/n 73576) were added and connected to the eyelet located on the top plate. The rounded handle allows for increased comfort while carrying when compared to the previous square handle. With the clip feature, the handle can be removed to allow for large crane hooks to attach to the eyelet. In addition, the color of the TP03 urethane bowl has been changed from black to yellow. This change was made to increase pump visibility while operating in murkier substances or liquids.

The SM50 Water Pump is a submersible, centrifugal type pump that requires no priming. The motor is contaminant-tolerant gear motor uniquely designed for continuous highspeed operation. The motor drives the impeller directly, so there are no spindle bearings that require periodic lubrication or replacement. The cast stainless steel, semi-closed impeller resists corrosion. A series of seals on the drive shaft effectively keep hydraulic fluid and pumped water where they belong while allowing the pump to be run dry without sudden seal failure. The SM50 is fitted with dripless flatfaced HTMA quick couplers for easy connecting and disconnecting of the pump and hydraulic system. The water outlet is 3-inch pipe thread fitted with a 3-inch groove fitting to which can be connected a cam hose end fitting. Access to the pumping chamber for cleaning requires the removal of only two capscrews. The motor with the impeller attached is then easily removed from the pump casing. The SM50 can draw down water to a depth of 3.5 inches. Putting the SM50 in a sump will allow it to pump all but 3.5 inches of water remaining in the sump. The integral screen effectively keeps solids larger than 3/8 of an inch out of the pump. The pump will handle clear water and water containing up to 10% solids.