stanley hydraulic pump parts supplier

The TP03 and TP08 lines of trash pumps are a great example of the power of hydraulics when it comes to pumping liquids with solids. The TP03 pump provides 450 gallons per minute (1688 lpm) of discharge capacity and can pump solids up to 3 inch (76 mm) in diameter. The TP08 has a 800 gpm (3028 lpm) of discharge capacityand can pump up to 4 inch (102 mm) diameter solids.

A division of Stanley Black & Decker, STANLEY Infrastructure is the world’s largest handheld hydraulic tool manufacturer and a worldwide market leader, offering over 150 handheld hydraulic tools and over 30 mounted impact tools.

Stanley detwatering pumps, the pure power of hydraulic tools is also exemplified in our trash pumps. Our TP03 pump discharges an impressive 450 gallons per minute (1688 lpm) and can handle up to 3 inch (76 mm) diameter solids. Our TP08 discharges 800 gpm (3028 lpm) and can handle up to 4 inch (102 mm) solids.

The SM50 water pump is fitted with dripless flat-faced HTMA quick couplers for easy connecting and disconnecting of the pump and hydraulic system. The water outlet is a 3-inch pipe thread fitted with a 3-inch groove fitting to which can be connected a cam hose end fitting. Access to the pumping chamber for cleaning requires the removal of only two cap screws. The motor with the impeller attached is then easily removed from the pump casing. The SM50 can draw down water to a depth of 3.5 inches. Putting the SM50 in a sump will allow it to pump all but 3.5 inches of water remaining in the sump. The integral screen effectively keeps solids larger than 3/8 of an inch out of the pump. The pump will handle clear water and water containing up to 10% solids.

The HP8BD Hydraulic Power Unit is a small compact hydraulic power unit designed to provide power for underwater hydraulic tools requiring a single 5 gpm up to 8 gpm. The Stanley HP8BD Hydraulic Power Unit is...

The Stanley HP28 (TWIN8) Twin Circuit Hydraulic Power Unit offers a revolutionary design capable of operating two tools at 8 gpm simultaneously. For the first time, running two hydraulic...

The Stanley PD45 Post Driver is a heavy duty tool for driving a wide range of posts including #2, #3, & #4 lb/ft "U" channel, #3 & #4 Strong Back "U" channel, #1 delineator, up to 2-5/8 inch round, or up to 2-1/2 inch square posts...

The Stanley PD45 Post Driver is a heavy duty tool for driving a wide range of posts including #2, #3, & #4 lb/ft "U" channel, #3 & #4 Strong Back "U" channel, #1 delineator, up to 2-5/8 inch round, or up to 2-1/2 inch square posts...

90 lb weight class. 1-1/4 inch Hex. Nothing equals the impact force of hydraulic breakers. With the best power-to-weight ratio, higher blow energy, and...

Stanley"s New Utility Chain Saw is a revolutionary cutting method designed to change the way the job gets done. From ductile iron to plastic pipe, this chain saw will get you in and out of the job faster,...

The Stanley SM21 Water Pump is one of the lightest and most durable pumps available. It’s capability of pumping 300 gpm (1135 lpm) at a 50 foot head make it ideal for vaults, manholes and more specifically in...

Stanley Hydraulic Tools has a proud tradition of being a global leader in the development of a wide range of innovative hydraulic products used in a variety of industries and applications throughout the world. A division of Stanley Black & Decker, Stanley Infrastructure is the world’s largest handheld hydraulic tool manufacturer and a worldwide market leader, offering over 150 handheld hydraulic tools and over 30 mounted impact tools. Browse our full Stanley Hydraulic Tools catalog below.

Rental Tools Online offers many types and sizes of portable hydraulic pumps from different manufacturers. If you are not sure which type of pump you need or what specifications are important, this may help.

Urethane bowls are very lightweight and can do a good job with clean, clear water. It is not recommended for water that has a lot of abrasives in it as these will eventually deteriorate the tolerances between the impeller and volute causing a reduction in performance. They are not as long lasting if used for pumps with potential solids, like trash or sewer pumps.

Iron has been used for pumps for well over 100 years. It is tough and unlikely to distort under different temperature and pressure conditions. It is also very abrasion and impact resistant and is ideal for sandy environments.

Similar to the volute, there are different materials employed for the impeller. In a centrifugal pump (which all these are) the impeller is the part of the pump that spins around inside the pump body, flinging the liquid from the center, outward towards the discharge port. It is important to select the right impeller material for the type of job at hand.

Urethaneimpellers are very good for the same types of conditions as urethane bowls: cool, clean, clear water. The water should be less than 100 degrees or so to avoid distoring the shape of the impeller. It is not recommended for pumping solds as these can cause the plastic to crack or break.

Stainless Steelis the ideal choice for salt water or other corrosive liquids. It is very stable under different temperatures and pressures, and will usually be unaffected by pumping smaller solids.

Some manufacturers claim to get much higher flow rates and head pressures from the same hydraulic oil input flow rates and pressures as other manufacturers. The equations are complex, but the idea is simple. It takes a certain amount of energy to move a volume of water to a particular height; it just does. The power going in to the pump has to be somewhat higher than that to compensate for friction loss, heat, and so on. There may be some efficiency improvements gained by impeller or volute design, but these are not normally as significant as some manufacturers claim. Beware of numbers that are too good to be true!

The SM20 will out-pump most all gasoline engine driven pumps. There is no recoil starting, priming or suction hose as with gas engine driven pumps. It can be run dry without damage. Submersed into the water and with its easy hookup to a power unit, the SM20 is instantly pumping. The abrasion resistant cast iron inlet wear ring is easily replaced from the inlet sit of the pump. With only a few moving parts, the SM20 is virtually maintenance free.

These submersible pumps are powered by the hydraulic circuits of a utility truck. They can also be run with a portable power unit or any other hydraulic source as long as the pressure and flow are within the correct range. A great feature is that they are self priming and can also be run dry without damage.

These hydraulic pumps are typically used by utility companies working in manholes but can be used for any other application as long as it is with in what the pumps are designed to do. Please refer to the technical specs of these water and trash pumps for more info or give as a call with any questions.

DCP30 03-2006 SPECIFICATIONS Stanley Hydraulic Tools 3810 S.E. Naef Road Milwaukie, Oregon 97267 Tel 503•659•5660 Visit our website at www.stanley-hydraulic-tools.com Fax 503•652•1780 Hydraulic Tools 12VDC Water Pump DCP30 ITEM U.S.A. METRIC Voltage Requirement 12 vdc Current 9.5 amps Maximum Water Flow 3.3 gpm 12.5 lpm Maximum Water Pressure 40 psi 2.8 bar Cut-Out Pressure 45 psi 3.1 bar Cut-In Pressure 30 psi 2.1 bar Weight 12.6 lbs 5.7 kg Length 12.5 in 318 mm Width 11 in 279 mm Height 15 in 381 mm Use with Diamond Chain Saws The DCP30 water pump is intended to be used to supply water to the chain and bar on Stanley Diamond Concrete Chain Saws and other diamond chain saw brands as well. Features and Benefi ts The 12 vdc Water Pump is a threechamber positive displacement diaphragm pump. This pump will deliver water fl ow to a pressure of 45 psi. Maximum output fl ow is 3.3 gpm. At 40 psi, this pump will deliver about 2.2 gpm. The Water Pump has a built-in pressure switch which will automatically shut off the pump when pressure reaches 45 psi. The switch will turn on the pump when pressure drops to 30 psi. The settings of the pressure switch are preset and cannot be adjusted. The Water Pump is self-priming. It will draw water up to a maximum lift of 8 feet. The diaphragm construction allows the pump to run dry without damage. There are no rotating seals to wear or leak. The built-in thermal protection will automatically shut off the pump before it is damaged by overheating. The shut off will automatically reset after the pump cools. The pump has a fi nned heat sink for cooling. This makes the pump a continuous-duty pump. The built-in check valve maintains water pressure after the pump shuts off. It also prevents water from fl owing back into the water supply. If your water supply is from a potable water source, water in the pump outlet will not fl ow back into the water system. A strainer is provided in the suction line to prevent debris from entering the pump. The strainer is easily disassembled for cleaning. The clear cover allows you to see the condition of the strainer. The current draw will be between 3.6 and 15 amps, depending on outlet pressure. Model DCP30101 Water Pump

This included VAT scrappage for residential energy-saving measures like heat pumps and solar panels, a 12-month cutting of fuel duty by 5p per liter, and to support the decarbonization of commercial premises, targeted business rate exemptions for eligible plant and machinery used in onsite renewable energy generation and storage. This is complemented by a 100% relief for eligible low-carbon heat networks with their own rates bill.