mud agitator schottel made in china

The MAX2000® Agitator features a rugged cast iron gearbox that houses helical bevel gearing. The gear sets are precisely ground to prevent all but the slightest amount of backlash in the gear sets. This feature promotes longer life by eliminating the high impact forces generated when the unit is energized at start-up. Each helical bevel gear stage is 98% efficient. A typical worm gear set is only 85% efficient, since it loses most of its efficiency through the generation of heat.

Internal gears and bearings are lubricated with mineral oil. When the ambient temperature drops below 23ºF or rises above 140ºF, a synthetic lubricant should be substituted. A unique feature of the MAX2000® Agitator is the lower bearing, which can be maintained from the top of the tank. This feature eliminates the need for in-tank inspections of the lower bearing, and also provides a barrier of grease that can be expunged out the lower seal. The lower seals are arranged to accommodate the grease pocket and make for a four-tier layer of protection for the gearing. The end result means the lower bearing stays in contact with good, uncontaminated lubricant at all times. All four of these levels must be breached prior to loss of oil in the gearbox.

Derrick mud agitators include an explosion-proof, “C” faced motor, reduction gearbox (helical-bevel gears for horizontal agitators or all helical gears for vertical units), impeller, and shaft with assembly bushings. Motors range from 5 to 30 HP and may be supplied in several power configurations.

Attaching the motor directly to the gearbox protects correct alignment that can increase bearing life and provides 95 percent efficiency in power transfer to the impeller. Using this superior design surpasses standard worm drive gear assemblies by 30 percent, allowing Derrick agitators to do the same work at far less horsepower. By unitizing the motor and gearbox, weight and space requirements are reduced. Horsepower, mechanical configuration, impeller diameter, and shaft length are customized to tank dimensions and maximum mud weights. Available horsepower ratings* are: 5, 7.5, 10, 15, 20, 25, and 30.

JBQ series mud Agitator, Less than 5.5 kW drilling mud Agitator adopts the blender cycloid speed reducer, and it is applied to the drug liquids mixing tank. This mud agitator has the advantage of compact structure so it occupies small area. More than 7.5 kW Mud Agitator uses the turbo and worm gear speed reducer, with the large torque transmission、 the revolution is steady、it works reliablely and has great merit. Common model of mud agitator is JBQ5.5kW 、JBQ7.5kW 、JBQ11kW and JBQ15kW.The drilling mud agitator is an important components for GN Solids Control drilling fluids processing system.

GN Solids Control as a professional manufacturer for soilds control equipments, we have designed lots of high-quality products, and JBQ series Agitator is one of them. To keep both the mud uniformity and the suspension of solids, the mud agitator is used to agitate the mud consecutively and reliably.This agitator agitates the mud to make cuttings, silt and sand pass the solids control system without being precipitated onto the tank bottom. Due to the simplex turbine decelerator, this product is featured by compact construction, light weight, balanced transmission, low noise, high efficiency of transmission and strong agitating power. Therefore, it is a reliable product in the solids control system.

China manufacturer GN Solids Control offer the world with drilling mud agitator equipments.We are an exporter of drilling fluid mud agitator for Indian, Russian,middle east.etc..Our factory and company are Quality Management System ISO 9001-2000 certified.GN Solids Control operate international oil gas drilling mud separation system sales,service,manufacturing,distribution serivce.Buy drilling fluid mud agitatorfrom China manufacturer.Your best mud agitator for drilling mud circulation system.

Pump case 30 also includes the filter part 46 that the rear wall 38 from pump body 32 starts to extend.Filter part 46 and pump body 32 can be by casting or the integral unit of other suitable way formation.Manufacture (identical with the pump body 32) filter part being made up of high-abrasive material, compared with the prior art products (with reference to Fig. 1) that filter part is made up of the Web materials of Fast Wearing, it is possible to extend the service life of product.Filter part 46 is hollow, has the frustoconical side walls 43 of rear wall 38 taper inward towards pump body 32.Filter part 46 arranges mounting flange 51 away from the end of pump body 32.Second entrance 44 is provided so that the inside of fluid communication pumping chamber 36 and filter part 46.As shown in Figure 6, arranging six and lengthen feeding hole slot 45 in the sidewall 43 of filter part 46, hole slot 45 is arranged around sidewall 43 interval.The region of entrance 44 arranges multiple fluids distribution blade of lengthening projection 47 form of 12 vertical alignments.These projections 47 contribute to the smooth flow of mud materials, and reduce the eddy current being flow to pumping chamber 36 generation from filter part 46 by entrance 44.

Impeller also includes the pumping vanes 78 that four additional extends from the outer surface 58 of rear shield 56.These pumping vanes 78 substantially curved shapes, one end is arranged near the peripheral edge portion 77 of rear shield 56, and the other end is arranged near hub 52.In use, the mud materials sent in rear shield 56 region in pump under the turning effort of impeller 50 is pumped by these pumping vanes 78.

In response to the rotation of adjacent fan-wheel 50 in using, what this device 80 can produce mud materials circulates pattern, so that in disturbance impeller region deposition particulate matter, this to from sump eliminating particle be likely to bigger or heavier or dense time deposition solid extremely important.Flow channel 93,94 circulating mud material can be passed through so that dispersed deposition granule.After by the solid material disturbance of deposition, guiding device 80 also has the transfer passage 91 and 92 leading to impeller of arranged concentric.The rotation of impeller 50 causes pumping operation, is sent into by the mud materials becoming fluid in impeller 50 to remove.Therefore device 80 has dual-use function, is very suitable for being likely to deposit in the region of a period of time at solid carrying out pumping operation.