4 hose for mud pump pricelist

Designed for produced water/fresh water transfer. Typically used for hydraulic fracture used for hydraulic fracture damaged hydrant lines, or to replace a broken water main. Manufactured with NSF standard 61 approved materials for use with potable water.

A more economical alternative to our polyurethane layflat hose. Warflex is reinforced with high–tenacity polyester yarn and coated through the weave with a 70% nitrile rubber / 30% PVC blend for good chemical resistance for produced water. Less abrasion resistance and puncture resistance. Custom hose color and branding available on big volume orders.

The new Midwest Hose Layflat Deployer completes our extensive water transfer portfolio. Our Direct Drive System makes our deployer one of the fastest, most powerful, and easy to use on the market with the capacity to deploy and retreive layflat hose up to 16″ in diameter.

Designed for burner, test, acidizing, cementing, fracking, high pressure jetting, and H2S operations. Used as a flexible connection (instead of pipe) between the riser and manifold or around the ball joint of offshore drillings rigs.

Ideally suited for any high pressure hydraulic applications where there is a need for hoses to be Fire Rated and capable of working in extreme heat in the event of an emergency.

Designed for mud delivery, mud jumper, motion compensator, decoking, and water injection operations on a drilling rig. Used as a flexible connection (instead of pipe) between the standpipe and swivel (rotary) or between the pump and standpipe (vibrator) for pumping mud in drilling and exploration work.

Designed for mud delivery, mud jumper, motion compensator, decoking and water injection operations on a drilling rig. Used as a flexible connection (instead of pipe) between the standpipe and swivel (rotary) or between the pump and standpipe (vibrator) for pumping mud in drilling and exploration work. Can handle higher flow rates than Grade D.

Designed for cementing service or acidizing service on a drilling rig. Used as a flexible connection (instead of pipe) to connect the cementing pump manifold and cementing head.

Designed to operate between 2,000 and 3,000 psi for water well, core drill, blast, or shot hole operations on portable drilling rigs, work-over rigs, slim hole and seismograph rigs.

Designed for oilfield waste pit recovery service. Ideal for handling crude oil, salt and freshwater, tank bottoms, and drilling mud up to 35% aromatics.Tube is designed to handle diluted solutions of hydrochloric acids and diesel fuels.

Hoses have a higher working pressure than normally available chemical hoses. CPE handles a wide variety of acids, alcohols, salt solutions, and petroleum based products.

Lightweight chemical transfer hose designed for almost every common industrial chemical used in industry today (98% of chemicals) without staining / contamination.

Designed for applications that required the hose to slide easily or require visual confirmation of material flow. Great for pumping water and light chemical solutions. Popular with pumping equipment because it handles suction discharge uses.

Lightweight, flexible, rugged suction/discharge hose that has good chemical resistance. Excellent for transferring fertilizer solutions, septic solutions, and pesticides. Hose remains flexible in sub-zero temperatures. Helix serves as a scuff strip.

Economical general service suction and discharge hose used for pumping water and light chemical solutions. PVC helix increases flexibility and abrasion resistance while the smooth interior provides maximum flow.

Designed for water discharge in construction, heavy duty equipment rental, and mines and quarries. Soft-wall hose construction provides similar performance to a layflat hose but a higher working pressure and more abrasion resistance.

Designed for dry bulk transfer of bulk cement, grains, animal feed, and other dry abrasive materials. High abrasion resistant tube resists cutting and gouges. Can be rolled for transport and storage.

Designed for dry bulk transfer of bulk cement, grains, animal feed, and other dry abrasive materials. High abrasion resistant tube resists cutting and gouges. Can be rolled for transport and storage.

Mud discharge hose designed for petroleum waste, drilling mud, diesel, and water. The standard to transfer liquid mud at high pressures from the mud pump.

Designed for discharge of potable water or liquids not containing oils or chemicals from a supply ship to an offshore drilling rig or temporary water lines in construction or industrial applications. Tube meets FDA requirements.

Designed for use with push-on fittings for air tools, petroleum products, gasoline, mild chemicals or water. No clamps or special tools required. Hose reinforcement laid at the most effective angle for maximum strength and coupling holding ability.

Designed for transfer liquid propane gas or butane. Can also transfer natural gas in open, well vented areas at 1 PSI max. UL21 LP Gas/Natural Gas approved.

For gravity of electric pumps dispensing of oils, gasoline, diesel, and petroleum products. Typically used with farm or barrel-type pumps where UL approval is not required. Has static wire, designed for use with electric pumps.

Wire braid steam hose for saturated and superheated steam up to 250 PSI 450° F. Cover is pin pricked to allow venting to eliminate blistering and cover separation.

Designed for portable or production line welding in factories, ships, construction, etc. Meets RMA and CGA (Compressed Gas Association) specifications for Type VD.

Designed to handle oily mists used to lubricate pneumatic tools. Tube is good for air and oil. Suitable for light agriculture spraying such as diluted solutions of herbicides.

General purpose hoses for open end discharge. Non-absorbing, mildew proof, and rolls up flat for easy storage and handling. Common in construction, agriculture, irrigation, marine, and rental applications. PVC hoses resistant to oils, grease.

Designed to handle edible liquids, vegetable oils, salad dressings, vinegar, mustard and meat products requiring a sanitary hose which will not impair taste. Great for service with hot oil fat filters and fryers.

Designed for food and beverage dispensing, potable water, air breathing lines, packaging and equipment, lube lines, and other visual flow applications.

For suction/discharge use and allows visual flow inspection. Designed for industrial vacuum pumps, food and beverage dispensing, air and water supply, car wash, coolant lines, and deionized water systems.

Clear polyvinyl chloride tubing provides fullview of flowing product. PVC is good to excellent for acids, fair to excellent for alkalies, and excellent for most solvents.

Linear low density polythylene food grade tubing for standard industrial applications such as the transfer of air and liquids, water lines, water softener lines, pneumatic logic control lines, and vending equipment.

Designed for open end discharge applications. Uses include connections to fire hydrants, dust control water trucks, water spraying, and water discharge. Immune to mildew.

Preconnected to pump of an engine (and the booster tank) for putting out small fires near the tank without having to connect to a fire hydrant (brush pumper).

Designed as a hydraulic brake hose for vehicles and motorcycles. The average life of a brake hose is six years. Brake hoses swell with age and restrict flow. Generally all brake hoses on a vehicle deteriorate at the same rate.

Air Brake Tubing, Steel Brake Line Tubing Assemblies, Steel Brake Line Tubing Coils, Rubber Air Brake Hose, Silicone Coolant Hose, Silicone Heater Hose, GPR Radiator Hose, Rubber Heater Hose, Garage Exhaust Hose, Air Conditioning Hose

Camlocks, Petroleum Handling, Industrial and Oilfield Hose Ends, External Swage Hose Ends (Holedale), Crowsfeet Couplings, Sand Blast Couplings, Ground Joint Couplings, Bauer Style Quick Connects, Ringlock Fittings, Storz, Foot Valves and Strainers, Airline Accessories, Industrial Accessories, Clamps, Pressure Washer, Safety and Protection Products

Light weight and flexible for easier handling. Flexibility retained at low, even cryogenic temperatures (below -238° F). Excellent resistance to kinking or crushing. Suction and Discharge use. Up to 100% aromatics, no permeation of gases. All assemblies tested to 1.5 x working pressure.

Air conditioning, ambient air movement, dehumidification, heating, sewn construction, and insulated and non-insulated available. Excellent UV compensation with mold and mildew inhibitors for demanding outdoor conditions. Flame resistant in accordance with UL94VTM-O, California Fire Marshal, and NFPA701 Method 2 specifications.

Available in sizes 1/4″ – 12″. Operates in high/low temperatures. Fire safety up to 1200° F. No permeation of gases. Full vacuum. Annular is hydroformed, a process that enhances flexibility and extends the life of the hose. Suitable for oils, chemicals, gases, exhaust gases, water, steam, vacuum.

Unions conform to NACE, ISO, DNV, and API standards and are interchangeable with other brand name manufactuerers adhering to industry standards. Materials conform to ASTM A105N Forged Carbon Steel, AISI 4130, and AISI4140. NPT threads conform to ASME B1.20.1. Figures 206, 207, G, 1002, and 1003 have O-Rings.

Plug Valves, Swivel Joints, J-55 and N-80 Pup Joints, Integral Fittings, Steel Hose Loops, Crossover Adapters and Swages, Blast Joints, Manifolds, Bull Plugs and Caps

Schedule 40 Pipe Fittings, Schedule 80 Pipe Fittings, Merchant Steel Pipe Fittings, XXH Nipples and Schedule 60 Nipples, Forged Steel, Stainless 304/316 Schedule 40, Grooved Nipples, Fittings, and Couplings, Swage Nipples, Oil Country Swage Nipples, Bull Plugs, Oil Country Bull Plugs, Merchant API Couplings, Bolted Sleeve Couplings, ANSI Flanges, API Flanges, Orifice Plates, AWA Plate Flanges, Shedule 40 and Schedule 80 Butt Weld Fittings

37° JIC, Pipe, Pipe Swivel, O-Ring Kits, O-Ring, Split Flange, Face Seal, Hose Barb, Flareless Bite Type, Metric, BSPP, BSPT, Inline Live Swivel, 90° Live Swivels, 90° Dual Plane Live Swivels, Test Points, Thread ID Kits

Inverted Flare, SAE 45° Flare, Compression, Self Aligned, Polyline Flareless, Push-Connect, Push-Connect Air Brake, Compression for DOT, Compression for Air Brake Copper Tubing, Threaded Sleeve, Pipe Fittings, Needle Valves, Drain Cocks, Truck Valves, Ground Plugs, Multiple Shut-Offs, Hose Barbs, Push-On Hose Barbs, Garden Hose Fittings

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

The rugged DAE Pumps Gulfport D540H drainage pumps move clean and dirty water with small solids up to .32-inches. These submersible drainage pumps with 4-inch discharge can move liquid at 310 GPM up to 135-feet via 8.5 horsepower. This 60Hz pump is available in 575-600V.

Offering the same high-quality, the DAE Pumps Gulfport D540S drainage pumps move clean and dirty water with small solids up to .32-inches. These durable drainage pumps with 4-inch discharge can move liquid at 310 GPM up to 135-feet via 8.5 horsepower. This 60Hz pump is available in 460V and 575-600V.

DAE Pumps Gulfport D640X drainage pumps handle clean and dirty water with small solids up to .32-inches. These rugged drainage pumps with 4-inch discharge can move liquid at 260 GPM up to 250-feet via 11.5 horsepower. This 60Hz pump is available in 575-600V.

DAE Pumps Gulfport D640H drainage pumps move clean and dirty water with small solids up to .32-inches. These reliable drainage pumps with 4-inch discharge can move liquid at 340 GPM up to 170-feet via 11.5 horsepower. This 60Hz pump is available in 575-600V.

The reliable DAE Pumps Gulfport D640S drainage pumps handle clean and dirty water with small solids up to .32-inches. These durable submersible pumps with 4-inch discharge can move liquid at 700 GPM up to 100-feet via 11.5 horsepower.  This 60Hz pump is available in 460V and 575-600V.

The high-quality DAE Pumps Gulfport D740H drainage pumps move clean and dirty water with small solids up to .27-inches. These reliable drainage pumps with 4-inch discharge can move liquid at 300 GPM up to 254-feet via 15 horsepower. This 60Hz pump is available in 440-480V.

DAE Pumps Gulfport D840H drainage pumps process clean and dirty water with small solids up to .47-inches. These rugged submersible pumps with 4-inch discharge can move liquid at 760 GPM up to 240-feet via 31 horsepower. This 60Hz pump is available in 460V, 480V, and 575-600V.

DAE Pumps Gulfport D940H drainage pumps handle clean and dirty water with small solids up to .27-inches. The most powerful of our 4-inch drainage pumps come with a 4-inch discharge and move liquid at 560 GPM up to 325-feet via 36 horsepower. This 60Hz pump is available in 440-480V.

The high-performing DAE Pumps Sonora S540 Submersible Sludge Pumps handle thick, soft, wet mud and sludge with solids up to 2-inches. These heavy-duty submersible sludge pumps with 4-inch discharge can move material at 365 GPM up to 92-feet via 7 horsepower. This 60Hz pump is available in 230V and 460V options.

The Sonora S540 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

DAE Pumps Sonora S640 Submersible Sludge Pumps offer the ultimate performance in moving mud and sludge with solids up to 2-inches. With a 4-inch discharge, these sludge pumps transfer material at 420 GPM up to 100-feet via a 9.2 HP motor.  This 60Hz pump is available in 230V and 460V options.

The Sonora S640 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

The rugged DAE Pumps Miramar L540 Submersible Slurry Pumps process abrasive materials with solids up to 1-inch. These durable slurry pumps with 4-inch discharge move material at 308 GPM up to 57-feet via a 7 HP motor.  This 60Hz pump is available in 460V.

The Miramar L540 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

Offering the same high-quality, the DAE Pumps Miramar L640 Submersible Slurry Pumps move abrasive materials with solids up to 1-inch. With a 4-inch discharge, these heavy-duty slurry pumps process material at 440 GPM up to 75-feet via a 12 HP motor.  This 60Hz pump is available in 460V.

The Miramar L640 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

The heavy-duty DAE Pumps Miramar L740 Submersible Slurry Pumps transfer abrasive materials with solids up to 1-inch. With a 4-inch discharge, the Miramar L740 slurry pumps move material at 616 GPM up to 85-feet via a 15 HP motor.  This 60Hz pump is available in 460V.

The Miramar L740 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

DAE Pumps Miramar L840 Submersible Slurry Pumps move abrasive materials with solids up to 1-inch. With a 4-inch discharge, these reliable slurry pumps process material at 660 GPM up to 98-feet via a 20 HP motor.  This 60Hz pump is available in 460V.

The Miramar L840 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

The high power 4-inch DAE Pumps Miramar L940 Submersible Slurry Pumps move abrasive materials with solids up to 1.5-inches. These 4-inch discharge submersible slurry pumps move liquids and solids at 880 GPM up to 171-feet via a 50 HP motor.  This 60Hz pump is available in 460V.

The Miramar L940 is made of aluminum alloy for high corrosion resistance and the high-chrome (55HRC) impellers provide great wear resistance. The wide base is designed for stability while standing in thick material.

DAE Pumps Tampa 437 Submersible Slurry Pumps are rugged, reliable, and cost-effective pumps for transporting slurry, sand, and a variety of other abrasive materials. The durable DAE Pumps Tampa 437 offers an open stand or strainer, and agitator provides improved suction and movement of solids up to 1-inch through a 4-inch discharge. The ergonomic Tampa 437 submersible slurry pumps transfer solids and liquids at a flow rate of up to 476 GPM and with 5 HP.

DAE Pumps 455-P Submersible Slurry Pumps are rugged, reliable, and cost-effective pumps for transporting slurry, sand, and a variety of other abrasive materials. The DAE Pumps 455-P with an open stand and agitator allows for ideal suction and movement of solids up to 1-inch with a 4-inch discharge. The ergonomic 455-P submersible slurry pumps transfer solids and liquids at a flow rate of up to 594 GPM and with 7.5 HP.

DAE Pumps Tampa 455 Submersible Slurry Pumps are rugged, reliable, and cost-effective pumps for transporting slurry, sand, and a variety of other abrasive materials. DAE Pumps Tampa 455 offers an open stand or strainer, and agitator that provides greater suction and movement of solids up to 1-inch through a 4-inch discharge. The ergonomic Tampa 455 submersible slurry pumps transfer solids and liquids at a flow rate of up to 594 GPM and with 7.5 HP.

DAE Pumps Tampa 4110 Submersible Slurry Pumps are rugged, reliable, and cost-effective pumps for transporting slurry, sand, and a variety of other abrasive materials. The efficient DAE Pumps Tampa 4110 offers an open stand or strainer, and agitator that provides enhanced suction and movement of solids up to 1-inch through a 4-inch discharge. The ergonomic Tampa 4110 submersible slurry pumps transfer solids and liquids at a flow rate of up to 819 GPM and with 15 HP.

The heavy-duty and reliable DAE Pumps Galveston 3304 Submersible Sludge and Slurry Pumps are the latest technology in submersible pumps for transporting slurry, sand, and a variety of other abrasive materials. DAE Pumps Galveston 3304 pumps with a combined strainer with a partially open stand and agitator allows for ideal suction and movement of solids up to 1.5-inches with a 4-inch discharge. The Galveston 3304 submersible slurry pumps transfer solids and liquids at a flow rate of up to 792 GPM and with 30 HP.

Mud pump, refers to the drilling process to the drilling mud or water and other washing liquid machinery. The main components are volute, impeller, pump seat, pump case, support cylinder, motor seat, motor and other components. Impeller nut is cast iron, so corrosion resistance is good, and convenient processing technology. Pump seat is equipped with four skeleton oil seal and shaft sleeve, prevent shaft wear, prolong the service life of the shaft.

ATO offers high quality vertical mud pumps with thick, solid shaft and copper motor. Various models are available, such as 2 inch mud pump, 3 inch mud pump, 4 inch mud pump and 6 inch mud pump.

Vertical mud pump is used as suction and pouring of river mud, suitable for oil refining, construction, printing and dyeing, chemical industry and other industries.

505 mud pump hose products are offered for sale by suppliers on Alibaba.comAbout 51% % of these are rubber hoses, 19%% are pumps, and 1%% are mud pump.

A wide variety of mud pump hose options are available to you, such as 1 year, not available and 2 years.You can also choose from new, mud pump hose,as well as from energy & mining, construction works , and machinery repair shops mud pump hose,and whether mud pump hose is 1.5 years, or unavailable.

OPI 700 HDL TRIPLEX PUMP(Ref#7719T)  700 hp at 150 rpm, fully rebuilt, Cat 3408 engines (approx. 15000 hours and run very well)  Two available  Price:  $275,000 CDN each

NATIONAL 12P-160 TRIPLEX MUD PUMP(Ref#5586T) 3 available in India. 1600 HP, rated pump speed 140 strokes per minute, maximum fluid cylinder liner bore 6¾”, stroke 10", 10,000 PSI hydrostatic pressure of standard cylinder. 2.853 ratio of gears. 10" suction connection, 6" discharge connection. Valve pot mod .7., steel fluid ends, 5,000 psi pulsation dampener. Oilfield skid mounted. Performance Data: at 120 strokes per minute with 6¾” liners, pump will produce 4305 PSI and 574gpm. Set up for electric power. Dimensions and weight: 84,700lbs, 209"L x 113"W x 75"H. Built 1976. Located India, removed from offshore drilling rig.

NATIONAL 12P-160 TRIPLEX PUMPS(Ref#2355R)  3 available, driven by GE752 traction motor, 1600 hp, 12” stroke, 5000 psi, surge chamber, skid mounted, located Middle East  Price:  $310,000

NATIONAL 12P-160 TRIPLEX PUMPS(Ref#8938R)  3 available, overhauled by National Oilwell (ready in 2-3 weeks after purchase), 1600 hp @ 120 stroke per minute, 12” stroke, 5000 psi, skid mounted, GE Amerimex 752 traction motors, new liners, seats, valves and pistons  Price:  $295,000 each

NATIONAL 12P-160 MUD PUMP(Ref#2062Re)  Refurbished, complete with South West fluid ends and DC traction motors, located Middle East, 3 available  Price:  $720,000 each

NATIONAL 8P80 TRIPLEX MUD PUMP(Ref#9073R)  800 hp, 6-1/2” x 8-1/2”, FS, FS FE w/QC caps and cylinder head caps, Oteco 3” shear relief valve, suction screen, 5 x 6” centrifugal charging pump, powered by Cat 3412 diesel engine, rod cooling pump, Oteco type D pressure gauge, mud valves, bull wheel, master skidded, complete, good condition  Price:  $275,000

NATIONAL OILWELL 850 HP MUD PUMP(Ref#15442T)  Mattco API-9 fluid end rebuilt, very little use after rebuild, pulsation dampener, no engine, skid mounted  Price:$22,000

NATIONAL 7-P-50(Ref#6302R)  750 hp, 8” stroke, 6” suction inlet, 4” discharge outlet, piston size 4-1/2” – 7”,  max rod load 85,000#, approx. weight 11,500#, lubrication force fed, steel pump power end, double helical gears, 4.95:1 gear ratio, rod bearings sheel type replaceable, main bearings straight roler, pinion bearings spherical roller, crankshaft 1pc forged alloy steel, connecting rod knuckle joint, crosshead guide bronze replaceable, piston type fluid end Monoblock design, from high strength alloy steel, treated and sonic tested, Cat D379 diesel engine, 500 HP max linear bore size 3-1/2 – 6-1/4 x 7-3/4” stroke, test pressure 10,000 psi, gear ratio 2.742.8” suction line to 4 discharge stroke, location South America  Price:  $110,000

NATIONAL JWS 165 WELL SERVICE TRIPLEX PUMP WITH 140 BARREL WORK TANK(Ref#2633Tb) 5 x 6, Detroit 8V71 engine, standard transmission, skid mounted   Price:$87,500

NOV JWS 340 TRIPEX MUD PUMPS(Ref#2345T)  Two available, Skidded, Detroit Series 60 diesel engine DDEC V (475 hp), Allison 750 (6-speed) transmission with lock up control pane, Mission 4 x 5 centrifugal suction pump, 4” plungers, pulsation dampener, pressure gauge, safety valve, 10,000 psi fluid end, 5000 psi working pressure, NOV plug valve control manifold (4-valve) configured for 15k operation.  Can be configured to kill wells, acidize, cement, reverse circulate, drill out frac plugs or run in tandem.  Self-contained with fuel and fluid tanks and controls.  Steel canopy over skids, covered battery boxes, new batteries and disconnect switches.  Well maintained and in excellent condition.  Low hours on pumps and motors.  Ready to work.  Price:  $154,500 each

NATIONAL JWS300 MUD PUMP(Ref#2767R)  Series 60 Detroit diesel, 14 liter engine w/Allison transmission, mounted on oilfield skid, major overhaul, completely unitized with fuel tank, fluid end rebuilt by Matco  Price:  $195,000

NATIONAL OILWELL VARCO 308T-7(Ref#3358T)  4” Ceramic plungers, external drip lubricated, pulsation dampeners, John Deere 400hp engine, bypass oil filter, electric start, 200 gal fuel tank, well maintained, Hansen gear 7.25:1, Cobra with cooler   Price:$225,000

(2) NATIONAL C350 MUD PUMPS(Ref#3077N)  Standby – not pump in 15 years.  Pumped chalk continuously at 600 psi in a cement factory.  Complete with electrics and electric motor, complete, bull wheels and guards, complete, fluid end, pistons, liners, and valves.  Low hours.  Located Europe.   Price for both:  $105,000 loaded in a 40’ container

NATIONAL G700 14” STROKE DUPLEX MUD PUMP(Ref#8312Ta)  700 HP, 14” stroke, cast iron fluid end, surge chamber, 285 gpm @ 3550 psi with 5” pistons or 805 gpm @ 1265 psi with 8” pistons, mounted on skid 10’ x 23’ with enclosure, sold as is  Price:  $27,500

NATIONAL 5-1/2 X 10” MUD PUMP(Ref#14556Ta)  skid mounted with fuel tank, 471 Detroit diesel engine, 4 speed transmission, all new injectors  Price:  $16,500

NATIONAL C-100 DUPLEX MUD PUMP SYSTEM(Ref#10047R)  National C100 duplex mud pump (currently has 5-1/2” liners), gear end and mud end is in good shape, powered by 671 Detroit engine, 1000 gallon fuel tank capacity, tndem trailer mounted (air brakes), fully winterized enclosure with heater unit, locking doors and parts shelves, stairways and rails, 8” steel suction line/hose/sand screen pot/pole winch for adjustment of suction depth,   Price:  $50,000

IDEAL 5 X 10 DUPLEX MUD PUMP(Ref#9068T)453 Detroit engine (tall, not short), mounted on 5th wheel trailer, new bearings in crane case  Price:  $18,500

PERONI PTO/C TRIPLEX MUD PUMP(Ref#6306R)  110mm (4.331”) bore x 190mm (7.480”) stroke, 5000 psig, 125 rpm, 151.6 gpm, 350 psig, stainless steel flud end, Cummins Big Cam, Model NTC-350, built 1980, Eaton 23-speed manual transmission, Philadelphia Model 13HP-2 gear reducer rated 496 hp ratio 14:1, input 1760 rpm, output 126 rpm, pressurized lubricant system, fuel tank 300 gal, trailer mounted, 11’7”H x 41’4”L x 8’1”W double frame triple axle, king pin to 5th wheel, air brakes and lights, approx. 68,700#, located South America  Price:  $90,000

HHF 500 TRIPLEX MUD PUMP(Ref#2565Tb)   (Hongua International), year 2012, KTA 1150C (19-P750) engine, 6-3/4” cylinder diameter, 7-1/2” stroke, lots of spares  Price:  $150,000

NF-500 (CHINESE MANUFACTURED0 500 hp MUD PUMP(Ref#13723R)  Manufactured 2011, 550 gpm@3000 psi, Cat C15 diesel engine, pulsation dampener, mounted on Galvanized jack-up base, located Australia  Price:  $280,000

SKYTOP BREWSTER 7-1/4 X 14” MUD PUMP(Ref#13399Rb)  379 Cat didsel engine, Matco hi pressure forged steel fluid end, quick change valve heads, Hydril dampener, brand new expendables sill in box  Price:  $59,500

OILWELL 14PDH(ref#3813R)  7-1/4 x 14, Matco fluid end with screw type valve, covers and cylinder heads, Detroit 8V71 diesel engine, surge chamber, pip-off valve, 10 groove pully, 5-1/2” liners, mounted on oilfield skid, 1 year warranty on motor,  Price:  $90,000

OILWELL DUPLEX MUD PUMP(Ref#1190N)  Rebuilt with all new fluid end parts and rebuilt gear end, Detroit 8V71 diesel engine, mounted on oilfield skid, hand clutch, belt drive, belt guard, pulsation dampener, pressure gauge, pressure relief valve, cleaned and painted, factory specs:

OILWELL 4 X 6 MUD PUMP(Ref#8578T)  New belts, diesel power, new mud end parts, mounted on skid on 8’ x 16’ gooseneck trailer, ready to work  Price:  $28,000

DRESSER OMEGA TRIPLEX PLUNGER PUMP MODEL JL3000(Ref#362T)  3000 hp, built 1999, unmounted, rebuilt, freshly painted, and not used since  Price:  $165,000

EWS 440 UNITIZED MUD PUMP PACKAGE(Ref#599N)  refurbished Detroit Series 60 engine, refurbished Allison transmission, input horsepower rating 440 max, 320 max pump speed rating, 6” stroke length, 4-1/2” maximum piston size, 3000 psi fluid end working pressure rating, 3” (as required) discharge connection size, 6” (as required) suction connection size, 2” NPT accessory connection size, API#4 valve size, API#S-2 piston rod end, 35 gallon cancase oil capacity, 24 gallons liner wash capacity, internal gear ratio:  4.58:1, 6.517:1.  Price:  $200,000

DRAGON W-440 TRIPLEX 6” MUD PUMP(Ref#7756Ta)  skid mounted on 8’ x 28’ skid, Detroit 60 Series 8 cyl Turbo diesel power plant with 440 hp, on board fuel tank, M310 Series control panel  Price:  $132,500

L & L SMC T135-5 TRIPLEX 6” MUD PUMP(Ref#7756Tc)  mounted on 7’ x 21’ skid, Cat 6 cyl turbo diesel engine, in-line style system, hyd tanks  Price:  $29,500

MCFARLAND P38 PUMP(Ref#3917Ta)  low hours, 1”, 10,000 psi set up, pump can be configured for 18,000 or 25,000 psi, 60 hp electric motor, skidded  Price:  $27,500

FAMMCO TRIPLEX PUMP(Ref#2760T)  2 x SPM 600 HP 10K, 3-1/2 x 6’ stroke plunger, powered by (2) Cat C12 400 hp diesel engines, (2) Allison HT750 trans., (2) 4 x 5 cent pumps, (2) 5 x 6 slurry mixing pumps, 6 bbl mixing tub, 14 bbl averaging tub, mounted on 2002 tandem axle 8’6”W x 50’ step deck trailer  Price on Request

GARDNER DENVER PZ-11(Ref#10748R)  approx. 7000 hours, Cat 3512C (1476 hp), 5000 psi fluid end cylinder, 5-1/2” piston cylinder, antifreeze heaters, WPT W21-CG-300 Type 1 PTO clutch, 16 groove drive sheave, 16 groove bullwheel, 16 groove Kevlar belt with necessary guards, 5 x 6 x 11 charge pump c/w 50 hp@1200 rpm electric motor.  Discharge plumbing: 2” 5M XXH B/W Oteco gate valve, 4” 5M XXH b/w Oteco gate valve, 3” 5M Oteco popoff valve w/1502 connection, 2” 5M type D Oteco mud gauge with 1502 connection, Hydril 20 gal 5M pulsation damper.  Mounted on oilfield skid with separate, with expendables cabinet, knowledge box and removable engine skid for breaking the engine and pump into separate smaller loads.  Winterization package, oilfield lighting, explosion proof starters for charge pump, rod oiler pump and liner wash pumps.  Price:  $695,000 - Make Offer

GARDNER DENVER PZ9 TRIPLEX MUD PUMPS(Ref#7062T) Two Available, each complete with Cat 3508 diesel engines, pulsation dampener, and mud tanks with desander, desilter, etc.  Price for Package:  $110,000

GARDNER DENVER PZ9 TRIPLEX MUD PUMP(Ref#14850R)2 units available, no power, fully serviced to OEM specs in July 2008 and stored since then  Price for both:  $430,000

GARDNER DENVER PZ8(Ref#862T)  Rebuilt, complete, 8” stroke, 750 hp, alloy steel modular flud cylinders, 6-1/2” liners, liner wash system, API 7 valve pots, gear reducer, steel billet fluid end, pulsation dampener, suction connection, FF discharge connection, 4.5 gear ratio, skid mounted, 130”L x 88”W x 54”H POR

GARDNER DENVER PZ7 STYLE TRIPLEX MUD PUMP(Ref#1245Nb)  Reconditioned, inspected and tested.  550 hp input, Cat D379PCTA diesel engine (reconditioned), air start, muffler, standard instrument gauge panel, mounted on Cat rails, new 20CB500 air clutch, reconditioned radiator.  Belt drive assembly consisting of pump drive sheave, pump drive belts with belt guard, engine drive sheave, engine drive belts with belt guard, pillow block bearings.  Reconditioned Continental Emsco PD-45 12 gallon 5000 psi WP pulsation dampener.  New O’Drill/MCM ORV 21050 2” 1,000 – 5,000 psi WP shear relief valve.  New O’Drill/MCM 2” 0 – 6,000 psi WP type D mud pressure gauge.  PZ7 fluid modules complete with suction manifold and discharge strainer cross.  New CA-122 liner wash pump, pinion driven with spary nozzle system, water tank and hoses.  New fluid end expendables with 6” liners.  (3) runner oilfield type master skid with loading hitches.  New 5 x 6” R.H. centrifugal 178 series charge pump, 1-7/8 shaft, 10” impeller size, belt driven off pinion shaft, drive belts with belt guard.  New 6” fgure 400 hammer union.  New 4” 5000 psi WP gate valve, new 200 gallon air receiver tank, new air controls.  Price:  $455,000

Fitted with 5" Liner and pistons, bare pump, no extras, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED.

Fitted with 5” liners and pistons with washing and lubricating system, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with a rebuilt Detroit Diesel V1271 w/ Twin Turbo, 550 HP, with a chain case and a manual transmission

Fitted with liner & pistons, with rod washing & lubrication system, bare pump no extra"s, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with New CAT C13 (440 HP) diesel power unit, w/hand clutch, belt drive, belt guard, fuel tank.

Fitted with 5" Liner and pistons, w/washing & lubricating system, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with New CAT C15 (540 HP) diesel power unit, with manual transmission with 4 to 1 gear case, fuel tank.

GARDNER DENVER PAH(Ref#10664Rc)  rebuilt, Detroit 8V92 diesel engine, Allison 5960 transmission, new pistons, liners, valves, rebuilt engine   Price:  $210,000

Manufactured 2008, Cat C-9 new genset, 10 bbl tank, shaker, charging pump, Allison HT750 transmission, 1600 hours, mounted on mobile 52’ trailer  Price: $290,000

GARDNER DENVER PAH MUD PUMP(Ref#7546T)  8V92 Detroit diesel engine, Allison transmission, choke manifold on unit and charge pump, pistons and liners,  Price on Request

MUD KING PAH MUD PUMP(Ref#12669T)  Detroit Series 60 engine, Allison 750 transmission, 3” centrifugal pump, 90 bbl 2-compartment circulating tank  Price:  $290,000

GARDNER DENVER TRIPLEX MUD PUMP(Ref#8245Rb)  Completely rebuilt, new paint, skid mounted, new Detroit 671 engine 165 hp @ 1800 rpm, new fuel tank, lines and fluid end, multi speed transmission and clutch, 12 volt DC starting and operating system, 5” suction, 1742 to 10,000 psi discharge pressure, 8 – 138 gpm capacity, full functional control panel, mounted on oilfield skid, dims 240”L x 90”W x 60”H 12,000#  Price:  $39,500

KERR 2200 AND 3500 OR FMC M1214 TRIPLEX MIST PUMPS(Ref#7999T) Cat engines, 4 speed transmissions, rigged up with secondary containment, onboard lighting, winterization canvas for cold weather operations, Also available with Cummins or John Deere engines Priced from $77,500 to $97,500

GARDNER DENVER PQ172 TRIPLEX MIST PUMP(Ref#7827Ta)  Deutz F3L914 45hp 3 cyl air cooled diesel engine with electric start, manual transmission, gauges, 4’H x 4’W x 7.5’ long, 3” hardline, 22 bbl mixing tank, skid mounted  Price:  $17,500

GARDNER DENVER GXP TRIPLEX 6 X 16 MUD PUMP(Ref#11010T)  Skid mounted, twin Detroit 671 diesel engines, 30 ton, dimensions: 28’L x 11’W x 8’H   Price:  $32,500

GARDNER DENVER GXR 800 HP DUPLEX MUD PUMP(Ref#12423Rb)  Matco steel fluid end, pulsation dampener, fuel tank, gauges, controls, starter, mounted on oilfield skid, completely rebuilt engine and fluid end  Price:  $125,000

GARDNER DENVER FXN 7-1/4 X 14 MUD PUMP(Ref#1403T)  Cat 3408 engine air start with pump drive and belt guard, PD55 Hydril dampener, 750 gallon fuel tank, mounted on heavy duty drop deck tandem trailer,  low hours  Price:  $87,500

GARDNER DENVER FXN 7-1/2” X 14” DUPLEX MUD PUMP(Ref#8312Tb)  500 hp, on skid with Cat D343 engine, capable of 200 gpm @ 3000 psi with 4” pistons or 775 gpm @ 940 psi with 7-1/2” pistons, sold as is  Price:  $27,500

GARDNER DENVER FXN 7” X 14” DUPLEX MUD PUMP(Ref#6637Ta)Forged steel fluid end, quick change caps, Cat 3412 diesel engine, Hydril K20 3000 pulsation dampener, Demco 2” relief valve, belt drive, type F3000# pressure gauge, rod oiler pump, speed sensor, electric start, air clutch, skidded with roof, 3-1/2” x 20’L vibrating hose  Price:  $76,000

GARDNER DENVER FZ-FXZ MUD PUMP(Ref#4087Tb)  7-1/2 x 12, Tier 1 Detroit diesel 60 Series, 12.7L 500 hp, good gear and fluid ends, same-trailer mounted, 500 gal fuel capacity  Price:  $90,000

GARDNER DENVER FXZ 6-1/2” X 12” MUD PUMP(Ref#10287Tb)  Detroit 8V71 engine, hauled on 3 axle skid trailer with 1989 TTRAC International truck  Price:  $69,500

GARDNER DENVER FXN DUPLEX MUD PUMPS(Ref#8214R)  Two available, 14” stroke, 2” rod size, 400 hp, 75 strokes per minute, cast fluid ends, unitized on oilfield skid with Cat 3406 diesel engines, air start, new filters, oil and coolant, air receiver on deck, fluorescent lighting, drive belts with air clutch.  Gone over and in good operating condition, ready to be put into service.  Pumps currently have new 6” liners with production being 480 gpm @ 1000 psi.  All fluid end parts are brand new and never used, including the valves, gears, liners, pistons, rods, head gasket, and rod packing, equipped with pulsation dampener.  32’ long x 11’ wide x 7’ high 50,000# weight  Price:  $72,500 each

GARDNER DENVER FXZ 7-1/4 x 12”(Ref#8810R)  Trailer mounted, suction rod, suction strainer, twin GMC 150 hp engines, flywheel, belt guards, totally rebuilt 2011  Price:  $100,000

GARDNER DENVER FXZ 7 X 12 MUD PUMP(Ref#6602RD) only 1300 hours on new 12 Liter Volvo engine, air clutches, skid mounted, 20’L x 9’7”W x 8.4”H, 40,000#  Price:  $45,000

GARDNER DENVER 5-1/2 X 8 FXN DUPLEX MUD PUMP(Ref#6678T)  Cast fluid end, 671 Detroit, Spicer 6853-C transmission, hydraulic pump, air controls, 1” hyd hoses, skidded  Price:  $44,500

GARDNER DENVER 5 1/2 X 10 MUD PUMP(Ref#3261Rb)  6 cylinder Cummins diesel engine, hand clutch, 5 speed transmission, 5-1/2” liners, skid mounted, 10” stroke, ready to work  Price on Request

GARDNER DENVER 5 X 10 MUD PUMP(Ref#1480Tb)  air driven, used with cement for grouting wells, sitting 3-4 years, valves will need rebuilding, trailer mounted, air over hydraulic brakes, includes 28 joints of 21’ pipe  Price:  $39,500

GARDNER DENVER 5 X 10 MUD PUMP(Ref#5882Tb)  453 Detroit engine, battery start, mounted on oilfield skid with axles, starts and runs  Price:  $14,500

GARDNER DENVER FDFXDH MUD PUMP(Ref#14457T)  4” inlet, 3” outlet, pulsation dampern, new piston and rods, engine has been removed    Price:  $40,000

5-1/2 x 8” GARDNER DENVER MUD PUMP(Ref#4523N)  Manufactured 1960’s, rebuilt a couple years ago, skid mounted, 4 cylinder Detroit engine, used Supercharger, 637 hours on it, runs good, needs cosmetic work  Price:  $32,500

GARDNER DENVER 5 X 6 MUD PUMP(Ref#302Tb)  2 available, unmounted, rebuilt pumps, need normal expendables (neoprene is old in the valves etc)  Price:  $17,500

GARDNER DENVER FG-FXG 5 X 6 MUD PUMP(Ref#3510R)  Detroit diesel engine, mounted on tandem axle trailer, one suction and one discharge hose included  Price:  $39,500

GARDNER DENVER 5 X 6 MUD PUMP(Ref#13203T)  electric drive, in custom skid, fully rebuilt gear end and fluid end, excellent condition  Price:  $22,500

GARDNER DENVER FXF-DE8 4 X 5 MUD PUMP(Ref#10148T)  Manufactured 1996, new condition of gear and fluid ends, no engine, new 4” liners, new pistons, new chrome rods, new valves, new liner studs in head, new suction flange and gasket, new 2” steel discharge flange  Price:  $13,500

4 x 5 GARDNER DENVER PISTON MUD PUMP(Ref#7097Rb)  bull wheel or can be connected to hydraulic motor, 75% condition, needs some work  Price:  $5,500

GARDNER DENVER 5 X 6 HYDRAULICALLY DRIVEN MUD PUMP(Ref#2505T)  approx. 2500 hours, unmounted, (taken off a rig), fluid ends have not been rebuilt  POR

GARDNER DENVER PE5U 4X5 TRIPLEX MUD PUMP(Ref#11077c)  powered by Cat 3306 diesel engine, Eaton 5-speed transmission, manifold, enclosed building  Price:  $72,500

GARDNER DENVER PE5 TRIPLEX MUD PUMP(Ref#4692Ta)  Detroit 6V71 engine, electric start, radiator, 2” Shear relief valve, Spicer manual transmission, skidded  Price:  $25,000

GARDNER DENVER TEE PUMP(Ref#1654T)  Manufactured 1998, 1602 hours, 4" plungers with hydraulic charge pump, Detroit Series 50 (rebuilt), 5 speed, Skid mounted with fuel tank, Rebuilt expendables with seals, valves, seats, packings and gaskets.  Price:  $72,500

GARDNER DENVER TEE MUD PUMP(Ref#6440T)  New, unused, manufactured 2014, 4 available, bare pumps  Price:  $39,500 each  New Cat C7 engines available at additional cost

GARDNER DENVER TEE 4 X 5 TRIPLEX MUD PUMP  **NEW**(Ref#9115R)  4” piston and liners, well servicing valve and seats, bare pump, extras a extra cost, 2 available (1 plunger and 1 piston)  Price bare pump:  $64,000

(1) NATIONAL C250 DUPLEX MUD PUMP7-1/4 x 15”, New fluid end parts, bolt on valve cover, Rebuilt gear end, Pulsation dampener, new Cat C15 diesel or 12V71 diesel engine, Electric start, Controls, gauges, safety shut off, Master skid   Price with Cat engine:  $135,000   Price with Detroit engine:  $120,000

GARDNER DENVER FXK 7 1/4 x 14” DUPLEX MUD PUMP  New fluid end part, Rebuilt gear end, Detroit 12V71 diesel engine, Electric starter, Controls, gauges, Safety shut off   Price:$80,000

(2) NATIONAL C-150 DUPLEX MUD PUMP 6 ¾ x 12”  250 gpm / 550 PSI, New fluid end part, Rebuilt gear end, Pulsation dampener, Detroit diesel engine, Electric start, Controls, safety shut down, Master skid  Price:$80,000   6 weeks delivery

7” x 12” WHEATLEY DUPLEX MUD PUMP  (rebuilt), Model 27-12, powered by rebuilt 671 Detroit diesel engine, rebuilt gear end and fluid end, with all new fluid end parts, hand clutch, pulsation dampener, rod lubricating gland, pressure gauge, pressure relief valve, belt drive, belt guard, fuel tank, battery start, mounted on oilfield skid, cleaned and painted, guaranteed for 6 months, delivery 12 weeks after order  Price:  $42,000     Delivery 12 weeks

CENTERLINE 7-1/2 X 10 MUD PUMP(Ref#14556Tb)  high pressure, no engine, needs retaining liner cage and (1) side suction manifold needs replacing, unmounted  Price:  $39,500

WHEATLEY 5 X 10 MUD PUMP AND KING SWIVEL(Ref#1557Nm)  20 bbl tank, mounted on gooseneck double axle dual tires trailer, 1995 International single axle tractor, hoses, hydraulic valves and hoses  Price:  $95,000

CONTINENTAL EMSCO D500 DUPLEX MUD PUMP(Ref#5074Tb)  Trailer mounted, Detroit Series 60 diesel engine 14L, 40’ tandem axle trailer with hydraulic leveling jacks, currently working  Price:  $87,500

EMSCO D500 DUPLEX MUD PUMP(Ref#6329T)  16” stroke, 500 hp, ductile iron fluid end, Cat D353 diesel engine with radiator, 640 hp, 1300 rpm, inline 6 cylinder, 4 stroke, 6-1/4” bore x 8” stroke, (1473 in3) displacement, turbo charged (air to air aftercooled) aspiration, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons.  Price:  $37,500

EMSCO D500 DUPLEX MUD PUMP(Ref#6118Rh)  Emsco D500 duplex mud pump with steel fluid end, Hydril K-20-3000 pulsation dampener, belt driv with Cat D379 diesel engine, air starter, radiator, air clutch, mounted in 12’ x 29’L mud pump house with parts bin, controls  Price on Request

EMSCO D500 DUPLEX PUMPS(Ref#8722R)  Two available, Cat 3406C diesel engine, Cotta gear box, mounted in enclosed building 11’6” x 30’  Price:  $70,000

EMSCO D500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Tc)  500 hp, Mounted on skid with Cat D353 engine, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO D500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Td)  500 hp, Mounted on skid with twin Detroit engines, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO DA-500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Te)  500 hp, Mounted on skid with Cat D353 engine, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO D-300 6 X 14 DUPLEX MUD PUMP(Ref#3360Tb)  Excellent condition, skid mounted on tandem axle heavy duty lowboy trailer, fluid end rebuilt with new 6” liners, liner cages, piston rods, swabs, rod packing, oiler pump, new Mattco end plug, Detroit 8V71 engine (good condition)  Price:  $44,500

CONTINENTAL EMSCO D175 7 X 12” MUD PUMP(Ref#12068Nb)  powered by 8V71 Detroit engine, flued end and engine rebuilt, all new expendables, junk box, fuel tank, air compressor and air clutch, skidded.   Price:  $100,000

EMSCO D300 DUPLEX MUD PUMP(Ref#8210N)  7 1/2 x 14, Matco steel fluid end with screw off caps, Cat 3406 diesel powered, Air chamber, Spare fluid end parts, Air start, Fuel tank, On oilfield skid, Mounted in an 11’ wide metal building, Good condition   Price: $120,000

GASO5885-WS  QUINTUPLEX PRODUCTION PUMP(Ref#10309T)  Pump only.  5” stroke, 300 hp, steel billet fluid end, 2-3/4” ceramic plungers, Delrim disc valves, 838 packing, 6” RF suction connection, 3” RTJ discharge connection, 231 gpm max, 2020 psi, max 360 rpm  Price:  $82,500

GASO 3364 MUD PUMPS(Ref#9104T)  Two available, rebuilt, cast ductile iron fluid ends, used for oil service, bare pumps, no engines, unmounted, one is flanged for suction/discharge, one is threaded  Price:  $20,000 each

GASO 1860 4-1/2 X 6 MUD PUMP(Ref#14394T)  Fluid end completely rebuilt, powered by 3 cyl Deutz diesel engine, trailer mounted, hoses and misc parts  Price$19,500

GASO MODEL 1742 5 X 10 MUD PUMPS(Ref#3276Rb)  John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank w/lock cap, Dayton oiler pump systemand tank, 4” suction hose and winch boom, 4’ back up bumper guard, front and rear loading hitches, 44” bullwheel with power band belt, large belt guard, 8’ x 17’ base (mud boat)  Price:  $62,500

GASO 1742 MUD PUMP 2-1/2 to 5 X 10(Ref#2412Ta)  Cummins 150 hp reconditioned engine with snap-in clutch, 90 gal diesel tank with lock cap,  Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ back up drill pipe bumper guard, front and rear loading hitches, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard  Price:  $82,500

GASO MODEL 1654 MUD PUMP(Ref#6937T) 5 x 8, drive shaft included, new gears and bearings 2019, new pistons and piston sleeves 2021, new valve rubber inserts and valve cup gaskets 2022, very good condition  Price:  $18,500

GASO 1550 MUD PUMP 2-1/2 TO 5 X 10(Ref#2412Tb)  Detroit 671 engine with Snap-In clutch (Gen Set approx. 1500 hours),  replaced fluid end parts with 4” liners,  mounted on 8’ x 12’ trailer with adjustable pintle and DOT lighting, 75 gal diesel tank with lock cap, Dayton oiler pump system and tank, 4” suction hose and winch boom, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard, 2’ x 2’ x 5’ lockable HD toolbox, mouting beams and steel/bolts  Price:  $41,500

GASO 5 X 10 MUD PUMP 1742(Ref#4047Rc)  8’ x 17’ base (mud boat), John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank, Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ backup drill pipe bumper guard, front and rear loading hitches, 42” bull wheel with power band belt, belt guard    PRICE:  $73,500

GASO T4507 TRIPLEX MUD PUMP(Ref#999Nb)  Triplex single acting reciprocating plunger pump, 450 hp, reconditioned rental package, aluminum bronze fluid end with 5-1/2” plungers, 642 gpm@ 1095 psi, new AR valves (3/09), Cat 3406 engine,  260 rpm, max GPM 1039, Max PSI 1200, skid mounted, coolers, controls, gauges  Price:  $175,000

5x10 GASO MUD PUMP AND TANK SYSTEM(Ref#240N)  350 gpm @ 330# psi, skid mounted trailer w/6V71 Detroit diesel engine, shale shaker 4 X 5 Schrem, 1000 gallon tank, (2) desanders, hydraulic motor on mud pickup pump  Price:  $65,000

AMERICAN DUPLEX MUD PUMP  - NEW(Ref#14063N)  Model AXG (FG-AXG), capacity (with 5” liners) 200 gpm (757) x 310 psi (21 kgcm2), @ 100 rpm, bare pump, no engine  Price:  $25,000

UNION T68 TRIPLEX MUD PUMP(Ref#999Na)  Triplex single acting reciprocating plunger pump, 6” plungers, 405 hp, 4.95:1 gear ratio, powered by 8V92T Detroit diesel engine and transmission, 617 @ 1061 psi at 210 rpm, Max GPM 620, Max PSI 1060, skid mounted, cooler, controls, gauges  Price:  $130,000

1600 HP F1600 TRIPLEX MUD PUMP(Ref#1401N)  Made in China, electric motor, Model HHF1600, triplex single acting piston type, 7” x 12” max diameter of liner stroke, 120 spm, 1176kW (1600hp) rated power, gear ratio 4.206, 12” stroke of piston, pump valve API 7#, 7” max ID of liner, max working pressure 34.3 MPa (5000 psi), max displacement (130 s/min) 50.42L/s, diameter of discharge pipe 127mm (5”), diameter of suction pipe 304mm (12”), weight 25570kg (56,000 lbs).  combined v-belt transmission 800 kw (1072 hp) * 2, 25 (J)-5-7630 V-belt, transmission ratio 2.377, Model YZ08 motor 800kw, 60 hz, Model SB6”  8” J-12 1/2” charging pump, 8” diameter outlet, 6” diameter inlet, 200m3/h displacement, 55kW power of centrifugal motor  Price:  $425,000

BOMCO SJF-1600 MUD PUMP(Ref#9621R)  1600 hp, 12” stroke, 5000 psi, pulsation dampeners, pop off pressure release valve, pump pressure gauge, forged discharge manifold, overhead track for chain hoist, mounted on shipping skid, line washer pump, 6” liners, overall size:  192 x 128 x 105-3/4”, inspection report available, 4 available    PRICE:  $137,500 each

BOMCO F-1600 MUD PUMPS(Ref#6252T)  2 available, Built 2007, powered by 1500 hp GE traction motor  Model GEB29-A1, 5k fluid ends with pulsation dampener, liner washer pump and external oil pump, on a master skid with roof  Price:  $162,500 each

QINGZHOU ORF 1000 HP MZ-9 MUD PUMPS(Two Available)  (Ref#2798R)  Manufactured 2007 and 2008, 7” x 9” 1000 hp triplex mud pump, 5000 psi pulsation dampener, 5-star 5x6 centrifugal pump 50 hp electric motor, suction screen, centrifugal rod oiler, (2) 2005 Detroit diesel 560 14L 665 hp w/ zero hours, electric start, radiator, gauges, Wichita power grip clutch, all master skidded  Price:  $255,000

CONTINENTAL EMSCO MODEL FC2200 TRIPLEX MUD PUMP(Ref#2280T)  Complete without traction motors.  9” bore x 15” stroke, single acting, working pressure up to 7500 psi, (3) interchangeable forged steel fluid end modules with separate suction and discharge sections, Premium grade fluid end expendables with 6-1/2” pistons and liners, suction manifold with (3) 12” flanged inlets, SD8 suction desurger, pressure manifold with (2) 5-1/8” 10,000# API flanged outlets, liner wash system, 1 x 1-1/2” mission centrifugal pump p/b 3 hp electric motor, external power end lubrication pump, steel skid, suction line pressure relief valve, set of standard service tools  Price:  $675,000

EMSCO STYLE F1000 TRIPLEX PUMPS(Ref#9886T)  2 available, 6-3/4” liners with 644 gpm @ 2380 psi, belt driven charging pump, pulsation dampener, with 398 Cat engines, skid mounted, ready to work  Price:  $112,500 each

1200rpm) through WPT power grip 321. The unit is complete with a bull wheel, a set of V-belts, belt guard, a drive assembly and screw devices for tightening belts.

-The unitization includes an electric motor powered supercharging pump piped to the suction of the mud pump, an electric powered liner wash pump mounted and piped, engine and WPT power grip 321 controls at area of engine arrangement, industrial coating on all parts and labor to clean & make ready for shipment.

-Pump suction manifold is 12”, and intake flange diameter is 12”. A 12” valve is used in suction manifold. And two suction solutions are alternative, pump charging and self-suction.

-F-1000 mud pump is driven by diesel engine (Caterpillar 3512DITA, 1250 HP @ 1200rpm) through WPT power grip 321. The unit is complete with a bull wheel, a set of V-belts, belt guard, a drive assembly and screw devices for tightening belts.

-The unitization includes an electric motor powered supercharging pump piped to the suction of the mud pump, an electric powered liner wash pump mounted and piped, engine and WPT power grip 321 controls at area of engine arrangement, industrial coating on all parts and labor to clean & make ready for shipment.

-Pump suction manifold is 12”, and intake flange diameter is 12”. A 12” valve is used in suction manifold. And two suction solutions are alternative, pump charging and self-suction.

EWCOWH-600 TRIPLEX MUD PUMP(Ref#1183N)  Manufactured 1984, good condition, powered by (2) Cat 3408 engines, mounted on oilfield skid, located Southeast Asia, immediately available  Price:  $190,000

NEW CONTINENTAL EMSCO STYLE F-1000 TRIPLEX MUD PUMP(Ref#1287N)  triplex single action piston, max. liner size x stroke 170 x 254mm (6-34” x 10”), 140 r/min strokes rating, 753kW (1000 hp), Herringbone gear, 4.207:1 gear ratio, pressure and splash lubrication, 12” flange suction inlet, 5-1/8” flanger 5000 psi discharge outlet, 7-3/4” pinion shaft dia., 2” x 2” key, valve-over-valve API#6, approx weight 41,420 lb, fully interchangeable with Continental Emsco parts, complete with pulsation dampener, suction discharge, pressure gauge, complete fluid end expendables, guaranteed for one year, delivered to Houston from China factory,  2 available  Price, delivered to Houston:  $185,000 each      (30% deposit with order, balance due when shipped from China)

CONTINENTAL EMSCO F-800 TRIPLEX MUD PUMP(Ref#664T) 800 hp, 6-3/4”, forged steel fluid end, 50003 pulsation dampener, 3” Shear relief valve, skidded  Price:  $37,500

OFM600 TRIPLEX MUD PUMP(Ref#2497T)  Manufactured 2018, 1800 hours, very excellent condition, Detroit 60 Series engine, Allison transmission, 800 psi, dims/weight 20’ x 10’ x 8’, 20,000 lbs  Price:  $320,000

AXON HD-500 TRIPLEX PLUNGER PUMP(Ref#975T)  14 liter Detroit Diesel, 6061 Allison automatic transmission, rebuilt power end, new expendables in fluid end, new charge pump, skid, tanks, Pilfer 5 valve manifold, 15k fluid end, new paint  Price:  $215,000

WHELAND DUPLEX MUD PUMP(Ref#7936)  7-1/2 x 14”, Hydril K-20 pulsation dampener, Cat D342 diesel engine, 300 bbl 3-compartment steel mud pit with (2) 7.4 hp electric mixer motors  Price:  $55,000

FMC BEAN PUMP MODEL L1122DI(Ref#3916T)  122 hp, 91 kw, 1750 max rpm, 127 gpm, 519 lpm, 1300 psi, 9063 kpa, Baldor ECP4409T 100 hp motor, 1200 rpm synchronous speed, 60hz frequency, 460V (3P)  Price on Request

HYDRAULIC PUMP WITH KUBOTA ENGINE(Ref#5073T)  Lofa Industries hydraulic pump (6.2 hours) with Kubota V3800T engine, Hydac ELD cooling system  Price:  $24,500

Bean 35 mud pumps(Ref#7739R) completely rebuilt, skid mounted with Deutz diesel engine, 4 speed transmission, low 50 hours, stored inside   Price:$14,000

OILWELL C338H TRIPLEX WATER INJECTION PUMP(Ref#6530T)  3” plungers, 3540 psi max pressure, 336 hp @ 200 rpm input, Cat G3408 gas engine, Falk gear/transmission, 100 rpm input, 290 rpm output, ratio 3.793:1, service factor 1.98, 375 hp Price on Request

SPRAGUE SYSTEM 0-55 GPM, 3500 PSI DUAL SYSTEM PORTABLE TURBO DIESEL HYDRAULICPUMP  (Ref#9235R)  New Unit.  High pressure, low volume, self-contrained.  Capable of 5000 psi intermittent duty, designed for low maintenance and flow operation.  A single adjustable back pressure regulating circuit allows operator to adjust aircraft reservoir return condition and maintains a positive reservoir head pressure on the aircraft without fluid loss.  This feature allows the system to be used on drilling rigs with different reservoir pressure requirements.  Lighted control panel.  Automatic over temperature shut down, Reservoir high/low level automatic shutdown, Safety circuit boost pump pressure switch, loss of boost pump pressure automatically shuts system down, Phase reverse relay (does not allow pump to turn in wrong rotation), Automatic air removal device (this removes the air from the oil returning from the rig at flows up to 55 gpm automatically; results are no cavitation, longer pump life, quiet system.  Reservoir drain valve, Parking brake instrument panel lights 100 hp drive motor (Deutz 125 hp), International Reservoir and system fluid emperature indicator.  Chassis has a 2-wheel mechanical parking brake.  The lower portion of the chassis serves as f ull sized drain pan with drain valve.  Cabinet is skydrol resistant stainless steel.  Removable cover assembly for major maintenance with access doors for inspection and minor maintenance.   Price:  $185,000

TEST PUMP RIG(Ref#3417T)  Mounted on 12K GVRW trailer, hydraulic powered spool with approximately 500 of 2” hose, internally routed power and safety cable, 7.5 HP pump and motor, Whisper Watt 25kva 3-phase diesel generator with approx. 3100 hours  Price:  $45,000

HYDROPLEX 15K TEST PUMP(Ref#2496R)  Manufactured 2012, 15 gallons per minute, mounted on 2008 GMC C6500 truck with diesel engine, control box, manifold, 550 gal heavy duty Snyder Megatainer tank, 123,896 miles on truck  Price:  $85,000

SCHAEFER & URBACH BT 80-120 GERMAN MANUFACTURED TRIPLEX MUD PUMPS, POWERED BY AC MOTOR AND GEAR DRIVEN(Ref#6853N) 3 available “LIKE NEW”– Manufactured 2006, Speed Max/Count: 135 SPM, 220 bar – 350 bar (5000 psi), Max. Displacement 4,005 l/min at 150 bar, Max. pressure 1,565 l/min at 350 bar, Elin 6 AC Motor, 690V/75 Hz, 1000 KW, Mounted on skid 8100 mm long x 3000mm wide x 2960 mm high. 45,000kg, Sound level: 63dB(A)@ 7 meters, Operating hours: (1) 1668, (2) 1010, (3) 2069, NOV Mission Magnum 8 x 6 x 14 charge pump, Amtec 36 kw AC Motor, 400/690V/50Hz, NOV Mission Magnum 3 x 2 x 13 liner cooler pump, 2,2 kW AC Motor 400/690V/ 50 Hz, Hydrill K20 pulsation dampener, Zollern gear / mud pump, Located in Europe

MUD PUPPY MP-255(Ref#1065T) Mounted in 16" trailer with 3 stabilizing jacks, sand guzzler, 3 x 2 centrifugal pump needs replacing, 3100 hours, includes 4" hose for pick up pump  Price:  $49,500

MUD PUPPY 2000(Ref#7953T)  Manufactured 1999, 1000 gal holding tank, (2) 3 x 4 Mission Magnum pumps with mechanical seals, MC255-2C mud cleaner, sand guzzler, Versa-drill rig jacks, Perkisn engine, spare hyd pump and filters, well maintained, ready to work  Price:  $59,500

CUSTOM BUILT MUD PUPPY(Ref#6133Ta)  800 gallon capacity, mounted on Big Tex trailer, 2” x 4” screen, 200 gpm, manual jack, no engine – runs off rig   Price:  $25,000

MUD PUPPY MUD SYSTEM(Ref#3572R)  3 x 2 Baker centrifugal pump, powered by 3 cyl Lister, Mud Puppy pick up pump, hydraulic power pack, barrel shaker, desander, dual 2000 gal mud tanks, mounted on gooseneck trailer  Price:  $60,000

MUD MIXING SYSTEM(Ref#430N)  Manufactured 2004, Mud Puppy, Deutz diesel engine,  dual shale shaker, down hole centrifugal pump, mud mixing pump, 1000 gal capacity, 500 gpm system   PRICE: $112,000

2000 GALLON SHOP BUILT SHALE SHAKER(Ref#15419Tc)  5 x 8 screen, 3 x 4 mission centrifugal pump, desanding cones, 300 gpm pickup pump, 2009 Cummins 110 hp motor with 7,150 hours, mounted on 3 axle trailer  Price:  $19,500

MUD PUPPY 170-2SC(Ref#5864Ta)  Deutz diesel engine with brand new turbo, 3 cone manifold, new style hydraulic Parker pump and new style shakers, newer 118 pump, trailer mounted  Price: $55,000

MUD SYSTEM(Ref#13092T)  2200gal Split wall tank, Twin Cummins 3.9 deck, W/3"-4" centrifugal mixing ,desilting, agitation pump . Mechanical Seals, 5.9 Turbo @2500 rpm W/3"x4" Chrome centrifugal down hole pump. Mechanical Seals desanded return with cross tank flow back flange (For sudden fluid loss), Twin 4"x5" hydraulic shaker dual screen deck, 4 Jack hydraulic leveling system. 27000GVWR tandem axles w/electric brakes . trailer can be legally pulled in NV safety by 1-ton . Brakes are excellent. @20000.GVW, Hydraulic ports for Tibban type mud return sump pump . In tank cooling.  Unit capable of 1000"x 24" drill bore with 3-1/2IF Drill string. Using open jet Tricone or similar. Unit is ready    Price:  $77,500

EDGE MUD CONDITIONER(Ref#5510RC) 600 gpm, 2 shale shakers, 1 400 gallon trash pump (1 more optional), 4 desander cones, 1 desander “Cobra” circulating pump, pintal hitch, air brakes, tank and system like new (low hours), 1200 gal tank, 4 hyd leveling jacks, tandem axle, Deutz 3 cyl air cooled diesel engine and hydraulic pumps in a removable pad,   Price:$65,000

MCT500 MUD MAN MUD SYSTEM(Ref#844R)  Manufactured 2007, rebuilt 2 years ago, 3300 gal 2-section tank, mounted on heavy duty trailer, 480 volt/3 phase, diesel generator, 500+ gpm capacity, 5” desilter cone bank, leveling jacks  Price (without generator)  $115,000  Price with generator:  $130,000

8400 GALLON/200 BBL MUD MIXING SYSTEM(Ref#14692T)  Swaco shaker, 3 centrifugal pumps, Detroit 235kw generator, mounted on 2008 tri axle step deck trailer  Price:  $137,500

MUD TECHNOLOGY MCT-450 MUD SYSTEM(Ref#7707T)  Built 2021, trailer mounted, 100 hp John Deere diesel engine, 100 kw generator fully enclosed, 4 hydraulic leveling jacks, (2) 3 x 4 centrifgual mud pumps with mechanical seals, 3000 gallon 2-section tank with mud guns in the tank, excellent condition  Price:  $187,500

MCT-450 DRILL FLUID MIXING AND CLEANING SYSTEM(Ref#3602T)  Built 2019, 156 hours, 2400 gal capacptiy two section tank, split equally for clean and dirty volume.  High G-force linear shaker, 18 sq ft shale shaker screening area, 18 sq ft desilter screening area, 36 sq ft total screening area with long runway, (6) 5” cones, 450 gpm cleaning capacity.  25hp 178 Series electric centrifugal pump to pressure feed hydrocyclones, 30 hp 178 series electric centrifugal pump to pressure feed hopper, jet guns and supercharge.  480 volt/60kw/3 phase diesel generator, safety shutdowns on engine and generator.  High shear/low pressure mixing hopper, sack table, high shear submersed jet guns in both tanks, independent valves to isolate hopper and jet guns, mounted on 12k dual tan axle trailer, pintle hitch, electric brakes, 24’L x 8’4”W x 12’4” H – 20,140 lbs.  Price:  $172,950

MUD TECHNOLOGY RST-990 MUD MIXING AND CLEANING SYSTEM(Ref#3444T)  1000 gal (approx.) 2-section tank, H G-force linear split shaker, centrifugal pump for mixing and desander, 480 volt/3 phase generator, 320 gpm cleaning capacity  POR

Gardner Denver mud pump rated at 1.7M/3 min @215 bhp with conventional heads, pulsation chamber, Odrill relief valve, 3.0” mud valve, exhaust fan, mixing hoper, liner wash pump and lubricator, driven by Eaton hydraulic pump with gear reducer and rubber block gear box. Pump house fitted with core bench, storage