amt mud pump in stock

The AMT line of Diaphragm pumps features a 2-stage, heavy duty forged gear driven transmission. Often referred to as Mud or Sludge Pumps, diaphragm pumps are designed to pump mud, slurry, sewage and thick liquids that have the ability to flow. AMT Diaphragm pumps are available with a choice of drivers to meet your application requirements: gasoline, diesel or single or three phase electric motor. Built-in check valve assures self-priming to 20 feet after initial prime. Heavy  duty forged gear driven transmission is designed to operate pump at 40 strokes per minute for electric motor models and 60 strokes per minute for engine driven models. Each unit includes a 2” or 3” NPT steel suction strainer, two NPT nipples and a wheel kit for portability. Models 338E K6, 338G-K6, 337H-K6 and 337E-K6 are kits provided less motor or engine. Suction and discharge port sizes cannot be reduced.

15 Models below. Made in USA. Gas, Diesel or Electric diaphragm pump, or mud / sludge pump. Easily maneuverable, the gas diaphragm pump is built for performance; Ideal for seepage dewatering, high suction lift, cleaning septic tanks, pumping industrial waste and marine tanks, small wellpoint systems and dewatering in sandy, muddy waters. Honda or Briggs gasoline engine or Electric diaphragm pump with motor.

Diaphragm Mud pump Suction & discharge port size cannot be reduced. Cast aluminum construction with thermoplastic rubber diaphragm. Also called a mudhog. 90 degree rotatable base on all models to fit through narrow gates. As a alternate in a centrifugal pump dredge pump design see 316F-95 2" mud pumps. Trash pumps, centrifugal Dredge Pump. Hoses and accessories.

The AMT line of diaphragm pumps features a 2-stage, heavy duty forged gear driven transmission. Often referred to as mud or sludge Pumps, diaphragm pumps are designed to pump mud, slurry, sewage and thick liquids that have the ability to flow. AMT Diaphragm pumps are available with a choice of drivers to meet your application requirements: gasoline, diesel or single or three phase electric motor. Built-in check valve assures self-priming to 20 feet after initial prime. Heavy duty forged gear driven transmission is designed to operate pump at 40 strokes per minute for electric motor models and 60 strokes per minute for engine driven models. Each unit includes a 2 or 3 inch NPT steel suction strainer, two NPT nipples and a wheel kit for portability.

Often referred to as Mud pumps or Sludge pumps, diaphragm pumps are designed to pump mud, slurry, sewage, and thick liquids that have the ability to flow. Designed for use with non-flammable liquids which are compatible with pump component materials.

Have questions about this product? Our pump experts are available toll-free at 888-817-8677. Our veteran engineers will help you quickly determine the best option for your application or project.

AMT has sold under its own name and under distributor branded names for over 70 years to the largest industrial distributors in the country as well as outside the country. The product line consists of a wide range of electric and engine driven centrifugal and diaphragm pumps in cast iron, bronze, stainless steel and aluminum in addition to a broad array of hand and barrel pumps for industry.

AMT is A Subsidiary of The Gorman-Rupp Company located in Mansfield, Ohio. AMT products are included in the Gorman-Rupp OTS™ off-the-shelf pump catalog offering shipment of many products within 24 hours. Call to confirm model availability.

Virtually every product AMT sells is engineered and designed by the company. Pumps are completely machined, assembled and tested at the Royersford facility.

The AMT 335E-96 diaphragm trash pump is designed to move thick liquids like sewage and sludge. Features a heavy duty 2 stage forged gear driven transmission that operates at 40 strokes per minute. Modular component design permits easy maintenance and cleanout. Wheel kit and handle are included.

The AMT line of Diaphragm pumps features a 2-stage, heavy duty forged gear driven transmission. Often referred to as Mud or Sludge Pumps, diaphragm pumps are designed to pump mud, slurry, sewage and thick liquids that have the ability to flow. AMT Diaphragm pumps are available with a choice of drivers to meet your application requirements: single or three phase electric motor. Built-in check valve assures self-priming to 20 feet after initial prime. Heavy duty forged gear driven transmission is designed to operate pump at 40 strokes per minute for electric motor models and 60 strokes per minute for engine driven models. Each unit includes a 2" or 3" NPT steel suction strainer, two NPT nipples and a wheel kit for portability. Models 338E K6, 338G-K6, 337H-K6 and 337E-K6 are kits provided less motor or engine. Suction and discharge port sizes cannot be reduced.

The AMT line of Diaphragm pumps features a 2-stage, heavy duty forged gear driven transmission. Often referred to as Mud or Sludge Pumps, diaphragm pumps are designed to pump mud, slurry, sewage and thick liquids that have the ability to flow.

The AMT 393B-95 is a Cast Iron Trash Pump and Motor unit with a Stainless Steel Impeller, Viton Silicon/Carbide Shaft Seal, 2 inch x 2 inch NPT Ports, coupled to a 5 Horsepower, 230 Volts, TEFC Totally Enclosed Fan Cooled, NEMA 184JM frame electric Motor. This sewage/trash pump is a heavy duty, centrifugal, motor driven, self-priming (to 20 ft. lift) unit, after initially filling casing with liquid. Pump is equipped with a silicon carbide mechanical seal, cast iron wear surfaces and a stainless steel clog-resistant impeller. Units are used to handle water containing sewage, stones, sticks, mud and other solids: maximum diameter percent the discharge NPT size. Handle liquids from 40 degrees to 180 degrees F (4 degrees to 82 degrees C) for use with nonflammable fluids compatible with pump component materials. All units come with built-in suction check valve to aid priming efficiency and easily removable casing/clean out cover and volute for quick debris clean out. Units are powered by totally enclosed fan cooled (TEFC) motors. Motor includes stainless steel shaft or stainless steel shaft sleeve.

AMT Cast Iron Sewage/Trash pumps are designed for trouble free and economical handling of solids laden liquids and slurries. Pumps are available in three NPT port sizes: 2¿, 3¿ or 4¿. Cast iron construction with two vane stainless steel self-cleaning impellers, silicon carbide mechanical seals for abrasion resistance and Buna-N O-rings and check valves. Built-in check valve allows pump to reprime automatically in an open system without the foot valve. The solids handling capabilities of the pumps make them ideally suited for a variety of industrial applications including: sewage treatment, canneries, chemical processing, wineries, tanneries, meat packing, breweries, pulp, wood chips, process water, sludge and slime, waste water, white water and other applications. These sewage/trash pumps will easily handle liquids containing sewage, stones, sticks, mud and other solids. Minimum liquid requirement must be above 85% — maximum 15% solids. Failure to do so may damage pump and void warranty.

AMT Pump is A Subsidiary of The Gorman-Rupp Company located in Mansfield, Ohio. AMT Pump offers over 1000+ different standard model numbers of which 400+ are readily available and offered as QSP, Quick Ship Products.

Virtually every product AMT sells is engineered and designed by the company. Pump components are machined, assembled and tested at the Royersford, Pennsylvania facility.

AMT Pump has sold under its own name and under distributor branded names for over 70 years to the largest industrial distributors in the country as well as outside the country. The product line consists of a wide range of electric and engine driven centrifugal and diaphragm pumps in cast iron, bronze, stainless steel and aluminum in addition to a broad array of hand and barrel pumps for industry. AMT Pump products are included in the Gorman-Rupp OTS™ off-the-shelf pump catalog offering shipment of many products within 24 hours. Virtually every product AMT sells is engineered and designed by the company. Pumps are completely machined, assembled and tested at the Royersford facility. AMT’s unique designs and patented products have made the company the industry leader for their high quality pumps. Nobody sells AMT PUMPS for less!

APPLICATION: Typical installations include hot and chilled water, boiler feed, condensate return, irrigation, high pressure washdown, booster service and fire protection/sprinkler systems, often referred to as “Jockey Pump”.