auger mud pump free sample

Kohler Gas, Three Speed W/ Two Speed For Coring, Moyno Pump , Cathead, One Winch, Has Wheels To Move On Hard Surface And Skids Can Be Bolted To Drag Machine.

6 Cyl. Ford Deck Engine, Moyno Pump, Water Tank, (2) Auger Racks, 6-5/8" & 4-1/4" 50" Each Augers, Includes Side Port Swivel And 3 1/2" Air Hammer. Auger / Air / Mud Drilling. Well Maintained, Mounted On Ford 8000, w/ Cat Diesel. Good Condition.

Deutz 4 Cyl. Diesel Deck Engine, Rebuilt 4 1/2 X 5 Gardner Denver Mud Pump W/ Reinforcement Plates For Mounting, Automatic Hammer, Automatic Hammer Calibration Done In 2019, (3) Leveling Jacks, (2) Winches, Can Add A Third Winch, New WRM Top Feed Swivel 2JW, U-Joint For Augers 1-5/8 HEX, Extruder For Shelby Tubes Samples, New More Info »

Cummins Deck Engine. Breakout Wrench, 3L8 Moyno Water Pump, Wiggle Tail, Wireline Winch, Hyd. Leveling Jacks, Mounted On 1992 Ford Single Axle, w/ Diesel.

3L6 Moyno Mud Pump. Safety Driver Winch, Cathead, Aux Winch, Main Winch, (3) 36”Jacks With Controls In The Drivers Area, Ready To Work, Mounted On ATV Carrier, w/ 4BT Cummins. Good Condition.

Duetz 57HP Diesel Deck Engine, 18" Mast, Angle Drill Capabilities, In-Out And Side To Side Slide Base, 435 Bean Pump, 140 Lb. Auto Hammer, 3,200 Lb. Main Hoist, (1) Wire Line, Recovery Winch, (3) Hyd. Leveling Jacks, (2) Side Tool Boxes, (3) Rod Racks, Front Auger Rack, Approx. 444 Hours, New Engine Installed In 2015, More Info »

Deutz 5 Cyl. Diesel Deck Engine. One Owner Rig, Cathead, 10K LB. Main Winch, 4,000 Lb. Aux. Winch, 3L6 Moyno Pump, 500 Gallon Water Tank, 4,688 Hours On Deck Engine Rebuild, 161, 914 Miles On Truck, Mounted On 1990 Ford F800 4 x 2. Good Condition.

3L8 Moyno Mud Pump. Breakout Table And Breakout Wrench, Auto Hammer (Replaced 2016), (4) Winches, Wireline 1800#, Main Winch 7000#, High Speed Aux 1800#, Low Speed Aux 3200#, 12250 Hours, Professionally Refurbished In 2013, 2250 Hours Since Refurbished, Mounted On ATV Carrier, w/ 4BT Cummins Turbo Diesel. Good Condition.

4 Cyl. Ford Deck Engine. Auto Hammer, 3L6 Moyno Pump, In/Out Slide Base, (2) Winches, 200 Gallon Water Tank, Front Hyd. Winch, (3) Leveling Jacks, Mounted On Yanmar C-60R, w/ Diesel.

3L6 Moyno Mud Pump, PTO, NO Deck Engine. (3) Hyd. Jacks, Safety Driver Hoist, Pullmaster Main Hoist, Auger Rack. Mounted On 1986 Muskeg Bombardier. Good Condition.

Bean Mud Pump, 6 Cyl. Ford Deck Engine. One Owner Rig, (3) Hyd. Jacks, Hyd. Safety Hammer, (3) Winches, In/Out & Side/Side Slide Base, 45" Of 6 1/4" HS Auger, 100" Of NW Rod. Mounted On 1986 Ford 8000, w/ 3208 Cat. Good Condition.

PTO, No Deck Engine. 1500 Gallon Water Tank, 3" Bowie Loading Pump, Heated Pump Box & Water Tank, Jake Brake, A/C. Mounted On 89 Ford 9000, w/ 3306 Cat. Excellent Condition.

3L8 Moyno Mud Pump, Cummins Diesel Deck Engine. Tandem Axle, (4) Hydraulic Leveling Jacks, (2) Winch Lines, Breakout Wrench, Side Port Swivel, Angle Drilling Attachments, (2) Swivel Auger Racks Mounted On The Rig, Drillers Stand, Sliding Drawworks, (Side To Side Also Back & Forward), Mounted On 89 Kodiak 70 Series, w/ 3208 Cat Diesel. Good More Info »

Bean 35 Mud Pump, Tooling For Auger Work And Diamond Core To 2000", Injection Pump, Low Hours, 71 XXX Miles On Carrier. Mounted On 76 International 4X4.

3L8 Moyno Mud Pump, (2) Winches, Toolboxes, Auger Rack, Hyd. Leveling Jacks, Electric Over Hyd. Controls, Deck Mtd. Hyd. Drive 2,000 PSI Steam Cleaner / Power Washer. Mounted On 90 International 4 X 2 w/ DT466 185 HP. Good Condition.

Betts provides environmental drilling, sampling, and assessment services. We are able to review subsurface impacts and monitor conditions over time on our job sites. We have experience sampling an array of sediment types as well as ground water. We offer direct-push technology (DPT) and auger/mud technology based on the needs of the project and geological condition of the site.

Betts provides direct-push technology (DPT) and uses the Geoprobe series 7822 track mounted rig. These rigs give maximum power and versatility in a relatively small and maneuverable package. Betts can perform soil and groundwater sampling as well as auger drilling if needed with these DPT rigs. The probe rigs can handle:

In addition to the DPT rigs available, Betts has more traditional (and larger) auger and mud rotary rigs available for soil sampling and well installations. Betts offers CME 75 and CME 55 rigs mounted on truck carriers and on ATV carriers for serious off-road needs. The auger rotary rigs can handle:

Mud rotary drilling is a fast and efficient method of drilling, effective in a wide range of geological formations, including sand, silt, clay, gravel, cobbles, and boulders. Also used for coring bedrock, it is not hindered by the presence of groundwater.

New and seasoned operators find that the Geoprobe® 3126GT makes SPT sampling through mud rotary drilling fast and easy. Once the drill mast is in position, the innovative centerline head side shift eliminates the need to move the drill mast again during drilling operations. Simply slide between rig functions used for SPT through mud rotary, including the GH63 percussion hammer, rotary head, automatic drop hammer, rod grip puller, and winchline. The fast transitions between functions made possible by the 3126GT head side shift and well-designed control panel maximizes drilling efficiency like never before.

Setting up for mud rotary drilling is easy on the 3126GT. Drive a five-foot conductor casing to depth using the GH63 percussion hammer. Without moving the machine, the drill mast is raised to make room for the mud pan. Once the mud pan is in place, extend the drill mast over the conductor casing. Then position outriggers to stabilize the mast.

At this point, the head side shift function has been used to align the rotary head over the casing. Rotate an NWJ drill rod while water is pumped through the rod, sub, and bit to wash cuttings up out of the hole and into the mud pan. Using the control panel, the operator can fine-tune water flow from the pump or activate the available hands-free controls. Once depth is reached, the breakout is used to help break the joint to remove the sub and bit. This makes work safer and easier on the drill crew. Then, shift the rotary head out of the way to use the winchline to pull the drill rod, sub, and bit from the hole.

The SPT sample is then ready to be taken with the hands-free Geoprobe® automatic drop hammer. A Geoprobe® interlocking split spoon sampler is added to the bottom of the NWJ rod string and lowered into the hole. Then, add an ADH drive cap to the top of the rod. Once in place, side shift the drop hammer over to take the SPT sample. With sampling complete, the drop hammer can be side shifted over in order to use the winchline. Using the Geoprobe® spring assisted swivel lift cap, pull the rod string and interlocking split spoon from the hole. Mud rotary drilling and SPT sampling can continue through the conductor casing until the desired depth is reached and all samples are taken. If sampling through drive and wash, the outer casing will continue to be put in place at each depth interval.

In addition to the positioning controls, head side shift, and well-designed control panel, other 3126GT features that make it easy for mud rotary drilling include: 105 inches of head stroke to help clear the hole with tooling when working over a mud pan, rod grip puller and 48,000 pounds of head pull back to retrieve conductor casing from the ground, storage for the drill rods on the side of the unit that makes for easy access, and the ability to use the rear blade of the machine to transport the water tank into place

New or seasoned operators can easily adapt to using the 3126GT for fast SPT sampling through mud rotary drilling. This next-generation machine is engineered specifically to increase geotechnical field efficiency. With the Geoprobe® 3126GT, you can drill more and make more.