badger mud pump free sample

The following are the steps our basement waterproofing contractors take when installing a sump pump system in your home. Badger Basement Systems" professional basement waterproofers can install a sump pump system in an average basement in one, sometimes two days. For a FREE sump pump installation estimate in Wisconsin and Illinois, including the areas of Eau Claire, Madison,and Rockford, call or e-mail us today!

A perimeter drain is installed on top of the drain, and a second layer of stone is placed on top. The purpose of this drain is to direct water from the basement wall-floor joint to the installed sump pump.

The drains installed by Badger Basement Systemsinclude a wall flange that extends up the basement wall to collect water that may leak from the walls. If your home has concrete block walls, holes can be drilled in the blocks to drain trapped water into your perimeter drain.

A sump pump pitis also excavated for the pump to be placed in. It"s important that the sump pit is large enough, but not too large. When placed in a small pit, a sump pump can pump water out faster than it can fill the liner, causing them to turn on and off quickly and burn out sooner. Sump pits that are too large tend to go too deeply into the ground, pulling up water far below your home, causing unnecessary work and electricity usage.

The sump pump is always installed in the lowest point in the basement. This way, if your home experiences a plumbing failure, the water will naturally flow towards the sump pump and be pumped away.

A line of PVC pipe is run from the perimeter drain to the sump pump system, and clean gravel is used to fill the empty space around the sump pump system. This gravel discourages mud and debris from settling up against the sump pump.

Badger Basement Systems of Madison, WI places your sump pump in a stand inside the liner, keeping it off the bottom, where dust, mud, and debris can settle. An airtight sump pump liner keeps odors and humidity from rising out of the sump pit while keeping out the sound of the sump pump running. If you have two pumps installed in the pit, we use two discharge lines to ensure that the pipes can handle the volume of the water being sent through them.

To allow for future testing, Badger Basement Systems installs several "ports" in the perimeter drain where a hose or dehumidifier drainage line can be inserted. During annual checkups and sump pump maintenance, this allows for additional flood testing.

To complete the sump pump installation, the concrete is cemented over, covering the drain over for a clean, attractive look. Unlike some other waterproofing systems, we do not leave a gap in the floor"s perimeter that can collect dust, debris, and other particles that could clog your waterproofing system.

Be sure to ask us about our battery backup sump pumps as well as our waterproof basement wall coverings,energy efficient dehumidifiers, waterproof basement flooring, and downspout extensions, and solutions for common home plumbing failures. We can also seal your crawl space, and many of our dealers can even finish the basement with waterproof products!

When you decide to waterproof the basement and install a sump pump in your home, Badger Basement Systems is ready to help you. They offer free, no-obligation visits and written sump pump installation quotes to all homeowners. Their contractors work throughout Wisconsin and Illinois, including the areas ofCaledonia, Eau Claire, Kenosha, Madison, Menomonee Falls, Mequon, Milwaukee, South Milwaukee, Oak Creek, Racine, Sun Prairie, Watertown,Wauwatosa, West Allis, in Wisconsin,and Belivdere, Loves Park, and Rockford in Illinois. Call or contact them online today to get started!

Mission Magnum 5” x 4” -30 hp mud mixing and circulating pump. 475 bbl steel pits available. 3-screen Double Life Linear Shale Shaker 500 gal/min capacity with 4 ‘2.5 hp’ Explosion-proof motors). 10” horizontal de-sander. 400 bbl dog house water tank

3,000 psi 11 ¼” Dorland- annular preventer with 3” 5,000 psi choke line & header, with hydraulic closing unit and Baker hand pump backup air over hydraulic backup closing unit.*Pipe and blind ram BOP available.

The Charge Free Stabilizer™ was designed to be installed directly before the suction manifold port between the mud pump and the charge pump. Maximizing mud pump performance by eliminating cavitation while isolating both the mud and charge pumps.

The Acoustic Assassin® was designed to be installed between the pump loop manifold and the production line. This fixture is a multi-chambered baffling system that will reduce damaging acoustic resonance generated by reciprocating pumps. The Acoustic Assassin® is an ideal addition to any pulsation control system.

The Charge Free Conversion Kit® is a high performance pulsation control kit that utilizes both compression and kinetic exchange for superior performance over traditional pulsation control methods of the past. With a gigantic increase in surface area, compression tuning, and a design to maximize energy exchange, the CFC Kits control pulsations from the pump while cleaning the signal for MWD tools.

Created specifically for drilling equipment inspectors and others in the oil and gas industry, the Oil Rig Mud Pump Inspection app allows you to easily document the status and safety of your oil rigs using just a mobile device. Quickly resolve any damage or needed maintenance with photos and GPS locations and sync to the cloud for easy access. The app is completely customizable to fit your inspection needs and works even without an internet signal.Try Template

The 2,200-hp mud pump for offshore applications is a single-acting reciprocating triplex mud pump designed for high fluid flow rates, even at low operating speeds, and with a long stroke design. These features reduce the number of load reversals in critical components and increase the life of fluid end parts.

The pump’s critical components are strategically placed to make maintenance and inspection far easier and safer. The two-piece, quick-release piston rod lets you remove the piston without disturbing the liner, minimizing downtime when you’re replacing fluid parts.

Specifically designed for drilling companies and others in the oil and gas industry, the easy to use drilling rig inspections app makes it easy to log information about the drill rigs, including details about the drill rigs operators, miles logged and well numbers. The inspection form app covers everything from the mud pump areas and mud mixing area to the mud tanks and pits, making it easy to identify areas where preventative maintenance is needed. The drilling rig equipment checklist also covers health and safety issues, including the availability of PPE equipment, emergency response and preparedness processes, and other critical elements of the drilling process and drill press equipment.