pressure washer mud pump in stock

Easily attaches to pressure washer and turns it into a high output pump. Great for flood clean up, car wash pits, emptying pools or chemical spills (discharge hose sold separately).

This awesome pump turns your pressure washer into a high volume sludge pump that can pump rocks and debris up to 3/4" in diameter! This pump quickly attaches to your existing pressure hose. During use it will provide a 11 to 1 or higher vacuum (4GPM produces 44GPM vacuum). The sludge pump is great for removing water from low areas, getting started with waste water reclaim, pool emptying, and flood and disaster clean up.

Attaches to any pressure washer and turns it into a high volume output pump. Great for flood cleanup, car wash pits, draining pools or chemical spills.

Sludge Sucker uses a high pressure water stream (1000-4000 PSI) to suck the sludge off the bottom of pits or tanks and eject it through a 1-1/2" (15 FT. long) hose to a disposal tank.

The Sludge Pump is a great tool for cleaning up water and slurries. Simply attach the pressure line from a portable power washer or car wash bay. The water flowing through the high pressure nozzle creates a powerful venturi suction that vacuums up slurry solutions. Debris as large as 3/4" will pass through the casting and out the discharge hose.

The base unit attaches to the end of a pressure washer lance with a 1/4 inch quick coupler for extension to the bottom of the pit. Uses a 0 tip for suction/power ejection. Base unit measures 6" long and 4" wide.

Pressure washer sludge pump attachments by leading manufacturer Suttner turn your power washer into a high output pump with ease. Available in 15 and 25 ft hose lengths, with a max pressure rating of 4000 psi. Contact us for help selecting the right sludge pump attachment for your pressure washer.

Pressure-Washer-Parts.com may store and sell products and chemicals that are known to the State of California to cause cancer, birth defects, and other reproductive harm.

The ST-36 sludge vacuum is a great tool for transferring a large amount of water or slurry in a short time. Simply attach the pressure line from a portable power washer or car wash bay. The water flowing through the high pressure nozzle creates a powerful venturi suction that can vacuum up slurry solutions. Debris as large as 3/4″ diameter will pass through the casting and out the discharge hose.

Based on clean water, the liquid ratio is about 1:11. If you are using a washer pumping 4 gpm, the output produced is about 44 gpm. Cleaning up chemical spills will not damage your washer pump. Applications may include: removing slurry from car wash pit, flood clean-up, removing rain water from construction site, empty pools, liquid transfer, run-off clean-up, etc.

OPERATION: (1). The high pressure line of the pressure washer is connected to the sludge vacuum attachment. The operator may connect the high pressure hose to the sludge vacuum inlet, or choose to hook the wand to the inlet. Water flow can then be controlled with the trigger gun.   After securing the attachment, run the pressure washer as normally instructed. (2). When the pressure washer is running, the exits a zero degree high pressure nozzle inside the durable aluminum die casting. This nozzle should have the same size orifice as the normal fan nozzles to produce the maximum pressure and flow from the unit. The velocity of the water flow exiting the nozzle creates a powerful venturi suction. This suction power can pick up the slurry, along with rocks and debris up to 3/4″ in diameter. Ensure the outlet hose is directed proper and place the sludge vacuum into the flood waters. It may be submerged all the way to the floor. The casting has small feet on it to keep it off the floor. (3). The operator should grip the outlet hose firmly, or secure it close to the end. If not held, the force of 40 to 60 GPM of liquid flowing through the discharge hose may cause it to push around. The discharge hose is normally 15′ to 25′ long. Lengths of 100′ can be purchased. Direct the discharge properly. Operators may need to check with authorities to see about discharging into a city drain. Many simply let it flow out onto lower ground, or dump it into a liquid tank truck. When the mucky water has been removed, the pressure washer can be used to finish the cleaning job.

We offer many options to handle your pumping and pressure washing needs. Our op discharge provides maximum motor cooling while allowing continuous duty operation.

Use this Suttner ST-36 Sludge Pump for removing rainwater from construction sites, cleaning up chemical spills, run-off clean-up, or any time you need to move liquid off a job site. Debris as large as 3/4 inch is able to pass through the casting and out your discharge hose. Based on clean water, this pump can move a ratio of 1:11, for example, if you"re using a 5 GPM pressure washer, you"ll move 55 GPM. This pump can move such a large amount of liquid in such a short time because the water flowing through the high-pressure nozzle creates a powerful venturi suction. All you need to do is attach a pressure line from a portable pressure washer.

Popular pressure washer parts: unloaders, valves, oil, filters, screens, ball valves, O-rings. Give us a call if you would like assistance finding the right replacement pressure washer part.