rotary mud pump drilling for sale

INGERSOLL RAND RO-300(Ref#2450N) Manufactured 1983, PTO, mounted on 1981 International Paystar 5000 with Detroit 8V92T engine, 650/250 air compressor, 5 ½ x 8 mud pump, 8 ½" retractable table, 3" x 28" Kelly, hydraulic pulldown, mechanical clutches, breakout wrench, 4 hydraulic leveling jacks, hydraulic valve problem in rear, mast does not move, rig does not start, truck does not run  Price:  $35,000

INGERSOLL RAND RO-300 DRILL RIGS(Ref#1555Ta)  Detroit V8 engine, 11 speed transmission, 5 x 10 Gaso hydraulic mud pump, 42’ mast, 8-1/2” retractable table, 4-1/2” x 25’ fluted round kelly, hydraulic drive winch, mounted on 1980 International, 4 hyd jacks Price:  $137,500

INGERSOLL RAND RO-300 DRILL RIG(Ref#1555Tb)  Detroit V8 engine, 11 speed transmission, (2) 5 x 6 Gardner Denver hydraulic driven pumps, 8-1/2” retractable table, 42’ mast, hyd driven double drum winch, w/ram driven kelly, 5-1/2” x 25’ kelly, mounted on 1981 International Paystar truck, 4 hyd jacks  Price:  $137,500

CYCLONE RO-300(Ref#10000R)  Manufactured 1970, 330 Ford porpane deck engine, 5-1/4" table, 3 x 4 centrfigual pump, mounted on 1973 Mack truck with 237 Cummins engine, 30" mast, sandline, no hyd pulldown, has not run in several years, good for parts or rebuilding  Price:  $36,500

CYCLONE 300 DRILL RIG(Ref#373T)  Manufactured 1973, 871 Detroit diesel on deck, 450 cfm Bendix Westinghouse air compressor, no mud pumps but hydraulics are there, 4” kelly, 8” retractable table, bailing line, mounted on 1972 Ford F900 tandem axle truck with 434 gas engine, 3 hydraulic jacks, 200’ of 4-1/2” x 15’ drill pipe, sitting since 2019  Price:  $37,500

CYCLONE 300(Ref#5693R) Manufactured mid 1970"s, Ford 300 industrial deck engine, mounted on 1985 Ford 600 (not 4x4) with 429 gas engine, 4 x 3 Mission mud pump, Leroi developmental air compressor, 5 ¼" retractable table, 3-1/2" x 19" Kelly, hydraulic pulldown, mechanical clutches, 300 gallon mud pit with mixer & hoses, breakout wrench, rod box, 200" of 2 3/8" IF x 15" drill pipe, bits & subs, 3 hydraulic leveling jacks, ready to go    PRICE:  $45,000

CYCLONE 44R(Ref#1509), Manufactured 1970 - combination mud rotary and cable rig,  Ford 6 cylinder gasoline engine on deck, 5 x 6 GD duplex mud pump, 34" mast, 3 hydraulic leveling jacks,  Mounted on tandem axle truck, Diamond Reo powered by Cummins 220 diesel engine,  3" x 24" kelly, 2-3/8" x 20" drill pipe, 13"H x 8"W x 34"L, handling equipment, table bushings, tools  Price:$45,000

CYCLONE 43R COMBINATION CABLE/KELLY(Ref#4485)  12" x 600" capacity, Mounted on tandem axle Mack truck, 4 x 5 GD mud pump, 38" mast, 6 cyl gas Ford 300 engine runs drawworks and pump, Large rotary table, hydraulic leveling jacks  Price to be determined

CYCLONE 42R ROTARY/CABLE COMBINATION RIG(Ref#5173N)  Ford Industrial gas deck engine, mounted on 1972 Kaiser 6 x 6 truck with 6 cyl Turbo diesel engine, (both engines rebuilt), 5" stationary table, 4" x 12" square kelly, King swivel, portable mud pit, 5" and 6" tools, no mud or air, no leveling jacks, no pipe  Price:  $45,000

SANDERSON CYCLONE 36R COMBINATION ROTARY/SPUDDER RIG(Ref#11403Tb)  4 cylinder Ford diesel engine on deck, 38" hydraulically raised mast, 5-1/2" table retractable to 18" x 12" deep, 3-1/2" x 20" fluted Kelly, drill line drum, sandline drum and casing drum (no line on rig).  2-part block, shock in the crown for cable drilling,  Mounted on 1992 Ford L7000 all-wheel drive truck with 6 cyl Ford diesel engine, automatic transmission with big hydraulic pump, low miles, 3 hydraulic leveling jacks, needs new hoses and swivel, no rod box.  Price:  $32,500 – Oklahoma

SANDERSON CYCLONE(Ref#15013T)  4 cyl Red Seal Continental gas deck engine, 2 line machine, shortened mast, mounted on 2-1/2 ton Military truck with gas engine, no jacks, currently drilling, well maintained and ready to work POR

CYCLONE 36R COMBINATION CABLE TOOL/KELLY PARTS RIG(Ref#3999N)  Manufactured 1981, 4 x 3 Mission, White diesel deck engine, developmental air compressor, 5" retractable table, fluted kelly, Bean water injection pump, mounted on 1981 Ford (not 4x4) with diesel engine, bailing line, sandline, casing line, 4 hydraulic jacks, pulldown, mechanical clutches, truck does not run, sitting over 10 years Price:$14,500 - Michigan

CYCLONE 36 COMBINATION CABLE TOOL/TABLE DRIVE DRILLING RIG(Ref#2328Ta)  Gardner Denver 5 x 6 mud pump with auxiliary engine, 5 cylinder deck engine, mounted on Ford truck with propane engine, retractable table, 1 front and 2 rear hydraulic leveling jacks (hydraulics redone), no rod box, no pipe rack, no drill pipe  Price on Request- Florida

CYCLONE 36R(Ref#3980N) combination cable/Kelly rig, manufactured 1960"s, (2) Ford gas deck engines, mounted on 1987 Freightliner with Cat engine, 3x4 Mission mud pump, 18" Kelly, 5 ¼" retractable table, hydraulic pulldown, mechanical clutches, mud pit, cone desander, 200" of 2 7/8" x 15" drill pipe, breakout wrench, hydraulic leveling jacks, 4" & 6" cable tools  Price:  $47,500

CYCLONE 36R COMBINATION CABLE/TABLE DRIVE DRILL RIG(Ref#7661Tb)  Gardner Denver 5 x 6 mud pump w/4 cyl John Deere engine, no air, 172 Industrial Ford gas deck engine, 5-1/4” retractable table, mounted on GMC tandem axle truck with gas engine, 3 hydraulic leveling jacks, pipe rack, 180’ drill pipe  Price:  $27,500

CYCLONE 36R COMBINATION RIG(Ref#11157)  2 Ford Industrial engines (one runs rig and one runs pump), mounted on 1964 International tandem truck with 220 Cummins, 5-1/2 x 6 Gardner Denver pump, 18" kelly, 5-1/4" retractable table, 2" swivel, 4" spudder tools, 375 gal attached swing-up mud pan, 180" of  Mayhew regular pipe  Price:  47,500

CYCLONE 36R(Ref#9430T)  Currently being rebuilt, 38" extended mast, Cummins 4BT deck engine, new 4 x 3 Mission mud pump, 8-1/2" Franks table, all new hydraulics, currently unmounted with no air compressor  POR

CYCLONE 35R(Ref#6558T)  5" Gardner Denver mud pump with 3 cyl diesel engine, no air, square kelly, retractable table, hydraulic pulldown, pipe rack, 4 cylinder diesel deck engine, mounted on 1985 Mack twin screw with diesel engine, 3 hyd leveling jacks, 300" of 2" x 16" drill pipe  Price:  $64,500

CYCLONE 35R COMBINATION MUD ROTARY CABLE TOOL RIG(Ref#10514T)  Built 1966, 5 x 6 mud pump, developmental air compressor, mounted on 1966 Ford F950 Super Duty with gas engine, (2) gas deck engines (one runs rig, one runs air compressor and mud pump), 240" drill rod, 15" sub and bit  Price:  $29,500

CYCLONE 35R(Ref#483N)  Manufactured 1969, Gardner Denver 3 x 2-1/2" pump (needs new pistons), mounted on 1977 International truck with DT466, 400" of 2-3/8 Mayhew Jr., stabilizers  Price:  $35,000

BUCYRUS ERIE 10R(Ref#5558Ta)  Manufactured 1974, mounted on 1974 Ford LN8000 with rebuilt Cat 3208, new front tires, no ruse, LeRoi compressor, 5 x 6 Gardner Denver mud pump, injection pump, new 2" plumbing, 8" retractable table, 3 hyd jacks, rod rack, 5 stabilizers 6"-12", 19 rods of 2-7/8", 26 rods of 3-1/2", several bits and subs 4"-10"

BUCYRUS ERIE 10R(Ref#11705T)  Manufactured 1973, 5 x 6 Gardner Denver mud pump (new pistons and liners 2016), 50 SDS air compressor, bailing drum, 24’ kelly, 8-1/4” retractable table, hydraulic pulldown, air clutches, mounted on 1989 Chevy Topkick with Cat 3208T, rod box, 300’ of 3” drill stem, tools, well maintained  Price:  $47,500  Additional pipe available at extra cost.

BUCYRUS ERIE 10R(Ref#13653T)  Manufactured 1972, 1500 drawworks, 5 x 6 mud pump, 680 cfm air compressor, 3-5/16" x 23" kelly (also a spare kelly), new stabilizer, breakout wrench, Myers water injection, 30" mast, 7-1/2" retractable table, pipe rack, mounted on 972 Ford L8000 truck with Cat 3208 engine, 3 hyd leveling jacks, 15 jts of 3-1/2" x 15" drill pipe (2-7/8 IF)  Price:  $52,500

BUCYRUS ERIE 10R(Ref#1402Ta)  Midway 1500 drawworks with 16" air cutches, 8-1/2" Midway rotary table operated by 8" twin disc clutch, Pullmaster hydraulic make up cathead, 45" derrick rigged up on 4 lines with King G53A swivel, 39" x 4-1/4" kelly, Detroit 6V71 Detroit deck engine, mounted on 1981 Western Star engine with Big Cam 400 Cummins engine, 10 speed transmission

Includes Gardner Denver FXZ 7-1/4 x 12 mud pump with 61381 Allis Chalmers 450 hp engine, air start, pump drive, belt guard, surge dampener, 500 gallon fuel tank mounted on tandem axle drop deck trailer

BUCYRUS ERIE 10R(Ref#1986Nc) Manufactured 1972, PTO, mounted on 1972 Ford F8000 with Cat 3208 engine, 5x6 piston mud pump, Leroi 50SDS air compressor, 8" retractable table, 5 ¼" table bushing, Myers water injection pump, line oiler, sandline, pipe rack, breakout wrench,  new water swivel, 40000# mast capacity, 16000# pulldown, mud pan, mud mixer, 1 front & 2 rear hydraulic leveling jacks, 270" of 2 7/8" OD x 20" drill pipe, 2 3/8" IF  Price on request

BUCYRUS ERIE 10R(Ref#14627)  Manufactured 1972, mounted on 1972 Ford truck, 300" of 3-1/2" x 15" drill pipe, 5 x 8 mud pump, small LeRoi compressor, rebuilt  Price:  $75,000

BUCYRUS ERIE 10R(Ref#7203N)  650/250 air compressor, no mud, 6 cyl Detroit on deck, mounted on 1978 Kenworth truck, 8V71 Detroit, water injection, no pipe or tools  Price:  $42,500

BUCYRUS ERIE 10R(Ref#1847N)  23" fluted kelly, table drive, LeRoi 450/250 air compressor, Mission 4 x 3 pump, mounted on Ford F800 tandem axle truck with gas engine, needs deck engine, hyd pump and rebuilding  Price:  $28,000

BUCYRUS ERIE 10R(Ref#1502N)  (2) 5 x 6 mud pumps, (1) 3 x 4 Mission Magnum centrifugal pump (low hours), mounted on Crane Carrier, Detroit diesel engine, PTO, hydraulic pulldown, mechanical clutches, retractable table, 3-1/2" x 23" kelly, breakout wrench, good condition, currently drilling, 155" of 3-1/2" pipe, 200" of 20" stems  Price:$65,000

Rotary table drive, Gardner Denver 5 x 6 FG-41 mud pump, Ingersoll Rand Type 40 air cooled air compressor, munted on 1979 GMC Brigadier J9500 tandem axle truck, 30’ x 9’ x 11’ (10’ with Kelly and lights removed)  Price:  $41,000

Manufactured 1975, double drum, refurbished, air compressor (PTO), 5-1/2 x 8 mud pump, mounted on 1975 International with 6 cyl Detroit diesel engine, 38"9" derrick, 3 lines to hook, 3" swivel (reduced to 2" mud hose), 3-1/2" fluted kelly, 5 ½" stationary table, pipe rack, no pipe available  Price:  $87,500

5 x 6 mud pump, stationary table, 4”  kelly, mounted on 1979 International truck with diesel engine, PTO, pipe racks, 4 hyd leveling jacks, 200’ drill pipe, needs new gearbox  Price:  $62,500

Detroit 671 diesel deck engine, no mud, no air compressor, retractable table, 26’ square Kelly (can run 33’ casing), mounted on 1981 GMC Brigadier with Cat 3208 engine, pipe racks (holds approx. 500’), hydraulic breakout, hydraulic pulldown, air clutches, 3 leveling jacks, 900’ drill pipe, 22’ 3-axle trailer, (2) 4-1/2” x 20’ drill collars, (1) 5-1/2” x 30’ drill collar, misc change overs and pick up plugs  Price:$54,500

Manufactured 1976, 750/250 air compressor, 10” retractable rotary table, Little Giant swivel, mounted on 4 axle Crane Carrier, 400 Big Cam engine (5000 hours), 1000’ of 3-1/2” x 20’ drill pipe (fits on rig)  Price: $117,500

Manufactured 1974, complete rebuild, 5 x 8 high pressure mud pump, 54’ derrick, 7-1/2” retractable rotary table (rebuilt 2018), Cummins 290 on deck, kelly bushing has been replaced, 290 Cummins deck engine, air clutches, wet clutch on main drive replaced, no air compressor, mounted on 4 axle Crane Carrier with 315 Cummins engine, 10 speed transmission, new clutch, tires 90%.  Includes 340’ of 4-1/2” x 20’ drill pipe, 6” stabilizer, 5” stabilizer, new tires (90%), brakes, clutches and bearings have been replaced  Price:  $215,000

Manufactured 1978, PTO, mounted on CCC with diesel engine, (2) 5 x 8 mud pumps, 3 x 4 Mission mud pump, 10" retractable rotary table, 4" fluted Kelly, no air, 4 hydraulic leveling jacks, no pipe available   Price Reduced:$165,000

Manufactured 1977, Cummins 400 Big Cam 3 engine (less than 300 hours since in frame), 5-1/2 x 8 Gardner Denver mud pump, Gardner Denver WEJ 750/250 air compressor with blower, 52" x 100,000# 4-line derrick, 2500" racking board, hydraulic power tongs range 2-3/8 – 4-1/2, mounted on 4 axle Crane Carrier, 4 cylinder Bean mist pump, hydraulic hydramatic trip hold back, hydraulic kelly hold back, 4-1/2" square kelly with kelly cock, 10" Gardner Denver rotary table, swabbing drum with 2000" cable.

Manufactured 1978, 5-1/2 x 10 Gardner Denver mud pump, no air compressor, 10" retractable table, mounted on 1977 Autocar with 350 Cummins engine, PTO, air clutches, 58" extended mast, 4-1/2" x 24" kelly (smaller kelly available), piep rack, breakout tongs, racking boards, chain pulldown, 5 hyd levelng jacks   Price: $165,000

GARDNER DENVER 14W DRILL RIG(Ref#13060Ra)  Manufactured 1973, 650/250 air compressor, Gardner Denver 5 x 6 mud pump, air clutches, 10” retractable table, 40’ mast,  4-1/2” x 25’ kelly, mounted on tandem axle Crane Carrier with 375 hp Cummins engine, 13 speed transmission, 3 leveling jacks, rod box, pipe racking stand, 210’ of 4-1/2” x 15’ drill pipe, running condition, does 65 mph Price:  $74,500

Gardner Denver 5 x 6 mud pump, big air compressor, retractable table, mounted on 1991 International 4800 truck with diesel engine, approx. 193,000 miles  Price:  $110,000

Gardner Denver mud pump, stationary table, 2-7/8" kelly, mounted on 1977International truck, approx. 300’ 2-7/8" drill pipe, 7-7/8" & 9-1/4" bits, running condition  Price:$62,500

Manufactured 1972, mounted on 1991 Morooka MST1500 track with Isuzu 4 cyl motor, dump bed, 100 hp John Deere deck engine, 5 x 6 mud pump, 300 gallon water tank Price:  $100,000

GARDNER DENVER 1000HD(Ref#15652T)  Manufactured 1979, 5 x 6 Failing mud pump, Leroi developmental air compressor, 23’ fluted kelly, 7-1/2” retractable Speedstar table, hydraulic pulldown, air over hydraulic clutches, pipe rack, breakout wrench, mounted on International truck with DT466 engine, 3 hyd jacks, 300’ of 20’ pipe

Manufactured 1957, 5 x 6 Gardner Denver mud pump (new gear end and fluid end), 7-1/2” retractable table, 24’ kelly, 35’ mast, chain pulldown with hydraulic motor, mounted on 1973 Diamond Reo double frame, 290 Cummins engine, 8 speed transmission, engine and transmission new, 2 rear and 1 front leveling jacks, 300’ of 2-3/8” drill pipe, mud pan, 2 bits, ready to work, new cables   Price:  $62,500

MAYHEW 1000(Ref#11322T)  Mounted on 1994 Ford truck, Cat engine, 7-1/2” table, 5 x 6 Gardner Denver mud pump, 23’ kelly, 2” swivel, hydraulic pulldown, water injection pump, 3 leveling jacks  Price:  $60,000

MAYHEW 1000(Ref#8472T)  Set up for drilling and workover, 4” square kelly, stationary table, mounted on 1974 International Lodestar, 5 x 6 Gardner Denver mud pump, no rod box, breakout tongs,  400’ of 2-3/8” x 20’ drill pipe, 10” surface bit, (2) 4” drill collars, 11 new button bits, 3 axle pipe trailer   Price:  $44,500

GARDNER DENVER 1000(Ref#13496T)  Manufactured 1979, 5 x 6 mud pump, 200 cfm air compressor, 5-1/2" retractable table, 3-3/4" x 23" fluted kelly, hydraulic pulldown, mechanical clutches, pipe rack, pipe wrench, mounted on 1979 Ford 9000 truck with Detroit 6V92, 4 hyd jacks, drills daily  Price:  $112,500

MAYHEW 1000(Ref#891Ta)  Manufactured 1978, 5 x 6 Gardner Denver mud pump, Gardner Denver air compressor, 5-1/4" stationary table, mounted on 1997 International truck with Cummins engine, 10 speed transmission, 30" mast, 25" kelly, chain pulldown, 2 rear leveling jacks, 300" of 2-7/8" IF drill pipe  Price:  $79,500

MAYHEW 1000(Ref#891T)  5 x 6 Gardner Denver mud pump, IR air compressor, 7-1/2" Mayhew rotary table, 30" mast, 25" kelly, chain pulldown, air clutch, mounted on 1996 Ford LT9000 truck with Cummins engine, 2 rear jacks, 300" drill pipe  Price:  $89,500

Manufactured 1970, only 200 hours since in-frame overhaul, mounted on 1970 GMC with straight 671 Detroit engine, 5x6 GD mud pump, GD 580 air compressor, 18" kelly, hydraulic pulldown, mechanical clutches, breakout tongs, pipe rack, 1 front screw jack & 2 rear hydraulic leveling jacks, 150" of 2 7/8"IF x 15" drill pipe  Price:  $47,500

Air compressor, 5 x 6 mud pump, 23" kelly, 7-1/2" rotary table, mounted on 1996 International truck with Cummins 350 hp engine, 300" of 2-7/8" OD with 2-3/8 IF drill pipe, air clutches  Price:  $90,000

5 x 6 Garnder Denver mud pump, Gardner Denver air compressor, 5-1/4" stationary rotary table, mounted on 1997 Ford L9000 truck with Cummins 350 hp diesel engine, chain pulldown, 23" kelly, new brakes, new drums, new kelly bushings  Price:  $75,000

mounted on Rio 6x6 with Cat 3306 rebuilt engine, Fuller 10 speed transmission, Gardner Denver 5 x 6 mud pump, Leroi 100s air compressor, 2000 stationary table, 3 ½" x 23" Kelly, water injection pump, 500 gallon water tank, hydraulic pulldown, mechanical clutches, breakout wrench, 2 rear hydraulic leveling jacks, 200 of 2 7/8" x 20" drill pipe and International

Completely refurbished 2010, derrick needs a little work, Mission Magnum Sandmaster 4 x 3 x 13 mud rotary pump, mounted on 1998 Mack CH613, completely with 2-3/8 pipe and various bits  Price:  $167,500

PTO, mounted on 1971 White Constructor with 290 Cummins engine, 6 x 6 Wheatley mud pump, 580 CFM air compressor, custom made 42’ mast, 36’ Kelly, stationary table, mechanical clutches, pulldown, 1 front 2 rear hydraulic leveling jacks, no breakout wrench, no pipe or tools available  Price:  $42,500

Manufactured 1970, PTO, mounted on 1970 Chevy with gas engine, 5 x 6 Gardner Denver mud pump, 185 CFM on board air compressor with John Deere diesel engine, spudding arm, 5-1/4" stationary table, hydraulic pulldown, 3 hydraulic leveling jacks, 23" Kelly, 210" of 2 3/8" x 15" drill pipe, stabilizer    PRICE ON REQUEST

5" stationary table, 4 x 5 Gardner Denver mud pump, developmental air compressor, 4" square kelly, hydraulic pulldown, mechanical clutches, mounted on 1990 GMC Kodiak truck with Cat 3208 engine, 3 hyd leveling jacks, pipe rack, 220" of 2-7/8" x 15" drill pipe  Price:  $49,500

Short wheel base, runs 15" pipe, 5-1/4 table, winch, 400/200 air compressor, 8 gpm water injection, mounted on Peterbilt 330 truck with Cat 3126E engine, RT8709B transmission, drill pipe, mud pit PRICE: $97,500

SPEEDSTAR 135(Ref#3612T)  (2) 5 x 6 Gardner Denver mud pump, 7-1/2" rotary table, chain pulldown, 7 speed transmission, 466 engine (210 hp), 1991 International truck, 4 leveling jacks  Price:  $95,000

SPEEDSTAR SS-135 DRILL RIG(Ref#11810Ta)  Manufactured 1976, 5-1/2 x 8 mud pump, 8-1/2” DSM retractable table, mounted on 1994 Ford LN9000 truck with Cat 3306 engine, breakout wrench, rod box, 4 hyd leveling jacks, tools, 1000’ of 20’ 3-1/2” flush wall drill pipe, ready to work  Price:  $112,500

290 cfm air compressor, John Deere deck engine for compressor, 8-1/2” retractable table, hydraulic pulldown, 5 x 6 Gardner Denvermud pump, mechanical clutches, mounted on tandem axle 1997 International 9400 truck with DT466 engine, approx 500’ rods, some tools, good condition, ready to go  Price:$102,500

SPEEDSTAR 135SS DRILLING RIG PACKAGE(Ref#14196T)  Manufactured 1969, mounted on 1998 International 4900 truck, 9 speed transmission, tires 90%, PTO, 7-1/2” retractable rotary table, kelly/swivel, 2 rear hydraulic jacks, 5 x 10 Gaso 300 gpm mud pump (gear end 95%)

Manufactured 1974, Gardner Denver WEJ 1009 air compressor with second stage cooling, Gardner Denver FG-FXF 5 x 6 mud pump, mounted on 1974 Crane Carrier with 8V71N diesel engine (motor refurbished), less than 10,000 miles, PTO, air line lubricator, water injection pump, double drum drawworks, single line pull 15,000#, friction clutches, large brakes, sandreel drum 8000# capacity, 8-1/2” retractable rotary table, pulldown, 2” pitch feed chains, 35’ heavy duty derrick, 4-1/4” x 24’ round kelly bar, 2” water swivel, pipe rack  Price:  $143,000

Manufactured 1983, 5-1/2 x 8 Gardner Denver mud pump, low pressure piston air compressor (compressor is 2 stage but only the low is working now), mounted on International 4700 with diesel engine, PTO, 11” retractable table, no rod box or pipe rack, some 3-1/2” x 20’ bottleneck pipe included  Price:  $72,500

standard mast & pullback, PTO, mounted on International with diesel engine, GD 5 ½ x 8 mud pump, Leroi air compressor, 500" of 4-1/2 x 20 flush joint drill pipe  Price:  $143,500

Gardner Denver 5 x 8 FXX172 mud pump, air compressor, 9" retractable table, 40" mast, pulldown, mounted on 1977 Crane Carrier, Cummins 855 diesel engine, 3 hyd leveling jacks, drill pipe  Price:$115,000

Manufactured 1977, PTO, mounted on 1977 CCC with 290 Cummins engine, 3x4 centrifugal mud pump, Leroi 500/100 air compressor, 8-1/2" retractable table, 4-1/4" x 23" kelly, breakout wrench, pipe rack, 1 front & 2 rear hydraulic leveling jacks, 300" of 4-1/2" x 20" drill pipe, needs new truck  Price:  $39,500

SPEEDSTAR 1500(Ref#3153T)  500/250 air compressor, no mud pump, rotary table, mounted on Mack truck with diesel engine, PTO, front wheel assist, rod rack, 700’ drill pipe Price:  $72,500

Manufactured 1979, mounted on International Paystar 5000 with 350 Big Cam Cummins engine, PTO, centrifugal mud pump, pipe rack, 3-1/2IF 20’ drill pipe, currently drilling.  Also includes unounted Gardner Denver 5-1/2 x 8 mud pump  Price:  $144,500

Manufactured 1989, PTO, mounted on 1981 International with Cummins engine, 4x3 centrifugal mud pump, 900 CFM air compressor, hydraulic pulldown, mechanical clutches, 4-1/2" retractable table, 3-1/4" x 25" Kelly, chain pulldown, 3 hydraulic leveling jacks, rod box, portable mud pit, 200" of 3-1/2" IF x 15" drill pipe Price:  $115,000

Manufactured 1980"s, Gardner Denver 5 x 6 mud pump, chain pulldown, 4-1/2" kelly, 8-1/2" retractable table, Mounted on 1983 Peterbilt truck with Cummins 350 engine, PTO, 2 rear and 2 front levelng jacks, 800" of 2-7/8" drill pipe  Price:  $122,500

Manufactured 1970"s, mounted on 1991 International with DT466 engine, 4 -1/2 x 5 Failing mud pump, auto chucks, 32" mast, 17" x 2 3/8" kelly, 2 leveling jacks  Price:  $37,500

1500 retractable table, 2-3/8" kelly, mechanical clutches, 5 x 6 Gardner Denver mud pumps, mounted on 1978 I6000 truck, Cat diesel engine, needs work (fluid ends needs rebuildeing, needs new hydraulic banks) Price:  $49,000 PRICE REDUCED: $34,500

1500 drawworks, PTO, mounted on 1996 International 4700 4x2 truck with DT466 engine, (2) drilling pumps:  Failing L100 800 max test pressure, 350 max working pressure and Gardner Denver FFFXFM 148.5 gpm, 639 max pressure, retractable table, mechanical clutches, hydraulic pulldown, 2 3/8” Kelly, 1 front & 2 rear hydraulic leveling jacks  Price:  $38,500

Manufactured 1966, 5-1/2 x 8 mud pump, mounted on 1972 Brockway 10 wheeler  truck with 781 Detroit diesel, PTO, 23’ kelly, 8-1/2” rotary table, breakout table, mechanical pulldown, mechanical clutches, hydraulic quills, 3 jacks    PRICE:  $64,000

Manufactured 1964, 5 x 6 mud pump, 2-3/8” kelly bar, 20” table (opens to 22”), heavy duty mast, 2 winches w/15” clutch, hydraulic pulldown, mounted on 1964 International truck, PTO, double plated frame, 304 International engine, needs minor repairs

Manufactured 1988, no mud pump, no air compressor, 6-1/2” inner diameter / 11” outdoor diameter retractable rotary table, 3-1/2” x 21’ kelly, mechanical chain pulldown, mechanical clutches, rod box, sandline, mounted on 1988 International FSeries 6 x 4 truck with DT466 gas engine, Eaton 10 speed tranmission, 200’ of 2-3/8” drill rod, truck and rig is operatable but could use some work, 3 leveling jacks  Price:  $41,500

Manufactured 1980, 5-1/2 x 8” Gardner Denver duplex pump, 23’ kelly, chain pulldown, air clutches, breakout wrench, 5-5/8” retractable rotary table, derrick 34’ from table to crown, mounted on 2005 Kenworth T300, 3 hydraulic leveling jacks, 260’ of 2-7/8” x 20’ drill pipe, roller and drag bits, very good condition, currently drilling  Price:  $137,500

2500 gallon Flatwater Fleet water tank, 300 gallon fuel tank, pump and hose, 2010 Kaeser M57 210 cfm air compressor (1200 hours), upper platform to carry two (2) pallets, spot lights, toolboxes, 162,000 miles  Price:  $62,500

Manufactured 1979, 5 x 6 Gardner Denver mud pump, Leroi 50S2 air compressor for drilling, 8" retractable table, 3-3/8" x 23"6"" kelly, 31"6" heavy duty mast, pulldown, mechanical clutches, Myers water injection, mounted on GMC Brigadier truck with 3208 Cat engine, 3 hydraulic leveling jacks, 500" , 3-5/8 x 15" drill pipe, bits, subs, good condition

Manufactured 1974, LeRoi 50S2 air compressor, 5 x 6 mud pump, 5-1/4" retractable table, 3-3/8" fluted kelly, 3 hydraulic leveling jacks, pulldown, mechanical clutches, breakout wrench, mounted on 1974 International tandem axle truck with Detroit 8V71 diesel engine (overhauled less than 1000 hours), 200" of 2-7/8" x 20" drill pipe Price:  $77,500

Manufactured 1973, 5 x 6 mud pump, 8” rotary table, 2-3/8” kelly, mounted on 1966 Kaiser Military 5 x 5 10-wheel truck with 6 cyl diesel engine, 200’ of 2-3/8” drill pipe, truck in fair condition  Price:  $49,000

5 x 6 mud pump, Leroi 50SD air compressor, 5-1/2” retractable table, chain pulldown, mechanical clutches, mounted on Ford truck, PTO, breakout wrench, rod box, approx. 300’ of 3” x 30’ (2-3/8 IF) drill pipe  Price:  $62,500

FAILING 1250 HOLEMASTER(Ref#796T)  Manufactured 1988, 5 x 6 Failing mud pump, (extra 5 x 6 pump included), 85 cfm Atlas Copco air compressor (can be remounted as an auxiliary compressor), 2” diaphragm mud pump, 7-1/2” retractable table, capable of drilling o 16”, mounted on 1988 International truck with DT466 (235 hp) engine, engine rebuilt 2012 with only 4000 hours), 10 speed transmission, 360’ drill pipe, tooling, 4-1/2” – 20” bits  Price:$122,500

Manufactured 1988, PTO, mounted on 1993 Ford 9000 with 250 Cummins engine, 9 speed Fuller transmission, 5 x 6 mud pump, no air, 5-1/4" stationary table, 2" Little Giant swivel, 18" x 3 5/8" round Kelly, hydraulic pulldown, mechanical clutches, breakout tongs, 2 rear hydraulic leveling jacks, 200" drill pipe, ready to go

Manufactured 1972, 5 x 6 mud pump, 50S1 LeRoi air compressor, pulldown, mechanical clutches, mounted on International tandem axle truck with gas engine, 40,000# mast, 15,000# drawworks, 3 drum bailer, single line pull, driller and helper"s platforms, hydraulic pulldown with 1-1/2" pulldown chains, 2" Little Giant swivel, toolracks, 3 hydraulic leveling jacks, 240" of 3-1/2" x 15" FJ (2-3/8 IF) drill pipe, LF breakout wrench, good condition, currently drilling  Price:  $90,000PRICE REDUCED:  $87,500

Manufactured 1980, mounted on 1980 International truck with DT466 engine, 5 x 6 Gardner Denver mud pump, no air compressor, 5-1/4” retractable rotary table, 3-1/2 X 24’ kelly, chain pulldown, 2” swivel, new fuel pump, new head gasket PRICE REDUCED: $48,500 - DEAL PENDING

Manufactured 1970, completely rebuilt, 5 x 6 Failing mud pump, developmental air compressor, sandline, mounted on 1990 Freightliner truck with Cat 3406 (600 hours), 5-1/4" retractable table, rod box, mechanical clutches, chain pulldown, 2" rebuilt swivel, new 32" mast, well maintained, ready to drill, no drill pipe

FAILING 1250(Ref#12693T)  Manufactured 1973, 5 x 6 mud pump, chain pulldown, retractable table, mounted on 1973 International truck, 345 gas engine, no drill pipe  Price:  $54,500

FAILING 1250(Ref#14820T) Manufactured 1965, mounted on 1970 Chevy with gas engine, 5x6 mud pump, 5-1/4” retractable table, 18’ kelly, hydraulic pulldown, mechanical clutches, breakout wrench, 1 front & 2 rear hydraulic leveling jacks, hydraulic pump has been removed, stored inside, sitting but running when parked  Price:$30,000

Built 1964, 4-1/2 x 5 Failing mud pump, Grimmer Schmidt 125cfm developmental air compressor, 5-1/4” stationary table, 2-3/8” kelly, 10" stroke, mounted on 1984 International truck with DT466 engine, PTO), 4 hydraulic over mechanical jacks, needs new tires

Manufactured 1965, mounted on 1979 International S series 2551 tandem axle truck with DT466 diesel engine, (2) mud pumps: Failing FM45 5 x 6 duplex and Gardner Denver FG FXG 5 x 6 duplex, Ingersoll Rand Type 30 250/125 air compressor hydraulically driven, 26’ x 25,000# derrick, 3-3/8” x 18’ kelly, King 15 KF water swivel, 1-1/4” pulldown chains, 5-1/4” rotary table with locking nut, air controlled clutches, welder, pipe rack, 150 gal mud pit, breakout tongs, 1 front & 2 rear hydraulic leveling jacks, stored inside, sitting but running when parked   Price:$35,000

5 x 6 Wheatley mud pump, Gardner Denver developmental air, hydraulic pulldown, mechanical clutches, stabilizer, mud pan, 3-1/2" kelly, stationary table, mounted on Ford Louisville tandem axle truck with 290 Cummins engine, PTO, 2 rear hydraulic jacks, 200" of 3-1/2" x 20" drill pipe, good condition, currently drilling  Price:  $65,000 PRICE REDUCED:  $50,000

Manufactured 1980, 425 cfm air compressor, 5 x 6 Gardner Denver mud pump, mounted on 1980 International truck with DT466 engine, retractable table, rod box, 600’ drill pipe  Price:  $69,500

3 x 4 Gardner Denver mud pump, 650/50 compressor, PTO, mounted on 1979 International 2-ton tandem axle truck with diesel engine, 3-1/2” kelly, 7-1/2” fixed table, 3 hydraulic jacks, pipe rack, mechanical pulldown, 300’ of 2-7/8” drill pipe (2-3/8 IF)  PRICE:$52,500

Mounted on 1974 Mack truck with V8 Mack engine, new 2" Little Giant swivel, 23" kelly, 5-1/4" rotary table, 256 LeRoi air compressor, 5 x 6 Gardner Denver piston pump, 2 hyd jacks, low hours, ready to work PRICE REDUCED: $72,500

Mounted on 1996 Ford F series 2 wheel drive with 5.9 Cummins diesel engine, 5-1/4" stationary table, 2 3/8" x 15" Kelly, 5x6 GD mud pump, chain pulldown, mechanical clutches, breakout wrench, rod rack, 255" of 15" Mayhew Jr rods, subs, bits, casing elevators, 4 hydraulic leveling jacks, ready to go

4-1/2 x 6 Gardner Denver piston mud pump, no air, 2-7/8" x 18" kelly (runs 10" x 2-708" rods), mounted on 2000 International 4700 w/DT466 engine, no drill rod, Mayhew Junior thread on kelly, all new hydraulic control valves, brakes clutches are all new or have recently been replaced  Price:  $37,500

Manufactured 1985, mounted on Ford F800 4 x 4 truck with diesel engine, front winch, rotary table, drawworks and mud pump are new, set up for 4” wells, drill pipe and tools included  Price:  $49,500

FAILING 250(Ref#3448T)  Manufactured early 1970"s, mounted on Ford 6 wheel drive Ford F750 truck, 391 gas engine, 4-1/2 x 5 mud pump, 290 cfm air compressor, 4" retractable table (no casing can go through), chain pulldown, 2-3/8 kelly, sandline, 10" stroke (can be pulled to 20"), running condition  Price:  $29,500

Manufactured 1980, Midway 1500 drawworks, PTO, mounted on 1980 International f-2574 with 1996 Detroit engine, 10 sp transmission, 38000# rear axles, 24.5 bud wheels, 16000# front axle w/22.5 floatation tires, 4 leveling jacks, 5 ½ x 8 mud pump, new 8-1/2" Midway retractable table, 3-3/4" x 34" fluted kelly (new 2011), 3-3/4" x 5-1/4" new master bushing, 49"2" mast with new cylinders (can run 44"5" casing), 3" plumbing, 2" swivel, 2" kelly hose, hydraulic pulldown, new drivemotor 2013, hydraulic cathead, 792 Spicer transfer case (rebuilt 2013 with air controls), new lifting cylindes on mast, new main hyd pump 2012, 4 part linesm BVM breakout tong, heavy duty work floor with hinged trap door

Manufactured 1975, drawworks completely rebuilt, 7-1/2 x 10 Gardner Denver mud pump, hydraulic pulldown, 54" derrick with racking board, rod box, mounted on 1978 International Paystar 5000 truck with 350 Cummins engine.  Price:$139,500

Manufactured 1975, 600 cfm/150 air compressor, mounted on 1975 Autocar with 350 Cummins engine, new tires, misc tools, bits, Gardner Denver 5 x 6 mud pump, 1998 Ingersoll Rand 600/150 air compressor w/3500 hours on 8/3 L Cummins engine  Package Price:  $112,500

MIDWAY 1500(Ref#15626R)  Manufactured late 1970’s, no mud pump, square kelly, no pulldown, 8” retractable table, mounted on newer Freightliner truck with diesel engine, air clutches, no pulldown, breakout tongs, 1 front and 2 rear hydraulic leveling jacks, no rod box, no pipe rack, 300’ of 20’ drill pipe (2-3/8” IF),  Price:  $54,500

Manufactured 1977, 600 cfm Leroi air compressor, 5 x 6 Gardner Denver mud pump, 8-1/2" table retractable, pull down, 9 gpm Bean pump, mounted on 1977 Ford 9000 truck with 671 Detroit engine (overhauled 2014), 600" of 2-7/8" drill stem, well maintained, ready to work  Price:  $162,500 PRICE REDUCED:  $105,000

Manufactured 1978, PTO, mounted on 1979 Ford 9000 with Cat engine, 5x6 mud pump, Leroi 750cfm air compressor, 3" x 23" kelly, 8" stationary table, breakout wrench, rod box, hydraulic pulldown, mechanical clutches, mud pan, 300" of 2 7/8" x 20" drill pipe, no leveling jacks, good running condition

PTO, mounted on 1991 Mack with diesel engine, 5x6 mud pump, GD air compressor, 7-1/2" stationary table, pulldown, manual clutches, rod rack, 2 hydraulic leveling jacks, good condition  Price:  $67,500

3 drum drawworks, mechanical clutches, Spicer air shift PTO, 2 rear hyd leveling jacks, 8” retractable table, 3-1/2” x 24’ square kelly, 2” Little Giant swivel, new 3 x 4 Mission mud pump, hydraulic pulldown, mounted on 1993 Freightliner truck with Cat 3406 engine, approximately 400’ of 2-7/8” full hole drill pipe  Price:  $62,500

Manufactured 1978, Triple drum, new bearings on drawworks and pulldowns, 5-1/2" x 8" Gardner Denver duplex mud pump, no air compressor, 57" x 60,000# hydraulic raised mast, Racking board, Mounted on 1978 Kenworth tandem axle truck with 8V92 Detroit diesel and PTO, 4 hydraulic leveling jacks and 2 rear screw jacks, Hydrostatic drive drawworks and rotary table, water injection, 8-1/2" retractable rotary table (4 speed transmission on rotary table), will run Range 3, 4-1/2" x 25" kelly, 4 speed hyd pulldown

Manufactured 1984, Leroi 600/250 air compressor, 5-1/2 x 8 duplex mud pump, 53’ tubular mast, racking bord, hydrostatic double drum drawworks, 7-1/2" hydrostatic rotary table, hydraulic pulldown, 24’ kelly bar, 3000’ capacity sandline, mounted on 1982 Kenworth C500 truck with 6V92TAC Detroit diesel, breakout tongs, hydraulic breakout wrench, hydraulic cathead with spinning chain, pipe rack, 1 front and 2 rear hydraulic jacks, 2-7/8" upset x 20’ pipe, 4-1/2" flush joint x 20’ pipe  Price:  $194,500

Manufactured 1978, Triple drum, new bearings on drawworks and pulldowns, 5-1/2" x 8" Gardner Denver duplex mud pump, no air compressor, 57" x 60,000# hydraulic raised mast, Racking board, Mounted on 1978 Kenworth tandem axle truck with 8V92 Detroit diesel and PTO, 4 hydraulic leveling jacks and 2 rear screw jacks, Hydrostatic drive drawworks and rotary table, water injection, 8-1/2" retractable rotary table (4 speed transmission on rotary table), will run Range 3, 4-1/2" x 25" kelly, 4 speed hyd pulldown

Manufactured 1976, PTO, mounted on International Paystar 5000 with rebuilt 350 Cummins engine, 6 x 8 Gardner Denver mud pump, 256S2 Leroi compressor, Bean water injection, 7-1/2" retractable table, 53" hydraulically raised mast, hydraulic pulldown, hydrostatic, breakout tongs, 4-1/2" hex Kelly (fluted available) no pipe rack or rod box

Manufactured 1974, 5-1/2 x 8 Gardner Denver chain driven mud pump (rebuilt), 256 LeRoi air compressor (rebuilt), 7-1/2” retractable table, mechanical clutches, pulldown, 4-1/2” x 23’ kelly (mast is set up for 30’ kelly), mounted on 1999 Kenworth truck with 440 hp Cat engine, PTO, pipe spinner, breakout tongs, water injection pump, 3 hydraluc leveling jacks, good condition,  rebuilt hydrostate, chain cases and rotary table, 200’ drill pipe and tools    Price:$175,000.

Manufactured 1974, PTO, mounted on 1974 Diamond Rio with Detroit 8V92 Detroit engine (3 years old), extended mast, rebuilt drawworks & Leroi 256S2 air compressor, no mud, sandline, 4-1/2" x 23" Kelly, breakout tongs, 8" retractable table, air clutches, hydraulic pulldown, pipe rack, 1 front & 2 rear hydraulic leveling jacks, 200" of 4-1/2" x 15" drill pipe, rig in operating condition Price:  $100,000 PRICE REDUCED: $79,500

Manufactured 1976, 3 x 4 centrifugal mud pump, LeRi 256S2 air compressor (very low hours on rebuilt), Detroit 8V92 deck engine, mounted on 1976 Paystar 5000 truck with International diesel engine, 3 hyd leveling jacks, 8-1/2" retractable table, 4-1/2" fluted kelly, new swivel, racking board, 38" mast, BJ tongs, air hammer, spare TKT transmission, some tools,

Manufactured 1972, Detroit 318 engine, 7-1/2” retractable table, 4” x 36’ kelly, chain pulldown, mounted on International 4900 tandem axle truck with 466 DT engine, 10 speed transmission, 400’ of 4-1/2” x 20’ (3-1/2 IF) drill pipe, 700’ of 4” x 30’ FH drill pipe, handling tools, last used 2021, 4 x 3 centrifugal MCM pump with John Deere engine  Price:$93,500

Manufactured 1979, mounted on 1979 International Paystar 5000 truck, 5 leveling jacks, 7-1/2" retractable rotary table, 26" kelly, 2" Little Giant swivel, 5-1/2 x 8" Gardner Denver mud pump, 256 LeRoi air compressor, racking board, currently working PRICE REDUCED: $92,500

PORTADRILL 120(Ref#9801T)  Manufactured 1968, 5 x 6 Gardner Denver mud pump, 6" stationary table, 3-1/2" x 23" kelly, mounted on 1987 Peterbilt with diesel engine, PTO, pipe rack

Built 1986, approx 540’ depth, double drum (shop build with triple clutch on each side), Gardner Denver 5 x 8 mud pump, 2” DSM swivel, 8-1/2” retractable table, trailer mounted, 46’ mast mechanically raised, 4” square kelly, 420" of 2-7/8" drill pipe  Price:  $47,500

Detroit V8 engine, 11 speed transmission, 5 x 10 Gaso hydraulic mud pump, 42’ mast, 8-1/2” retractable table, 4-1/2” x 25’ fluted round kelly, hydraulic drive winch, mounted on 1980 International, 4 hyd jacks Price:  $137,500

INGERSOLL RAND RO-300 DRILL RIG(Ref#1555Tb)  Detroit V8 engine, 11 speed transmission, (2) 5 x 6 Gardner Denver hydraulic driven pumps, 8-1/2” retractable table, 42’ mast, hyd driven double drum winch, w/ram driven kelly, 5-1/2” x 25’ kelly, mounted on 1981 International Paystar truck, 4 hyd jacks  Price:  $137,500

Built approx 2007, 150’ – 200’ depth capacity, rig has heavy duty railroad winch cable for up and down drilling operations or for pulling pumps, 3” centrifugal mud pump, IR 40 cfm developmental air compressor, pump and compressor run off Handona gas engines, boom will handle 10’ or 20’ rods, mounted on 1998 Ford 700 2 wheel drive truck, 7 ltr propane engine, (2) tanks (40 and 80 gal), drilling, hydraulics and truck run on propane, 500 gal water tank, pipe rack, compact rig.  Includes approx 120’ of 1-1/4” x 10’ rods, bits for 1-1/4”, 2” and 4” wells,  Price:  $30,000

Manufactured 1974, mounted on 1974 Ford LN8000 with rebuilt Cat 3208, new front tires, no ruse, LeRoi compressor, 5 x 6 Gardner Denver mud pump, injection pump, new 2” plumbing, 8” retractable table, 3 hyd jacks, rod rack, 5 stabilizers 6”-12”, 19 rods of 2-7/8”, 26 rods of 3-1/2”, several bits and subs 4”-10”

Manufactured 1973, 5 x 6 Gardner Denver mud pump (new pistons and liners 2016), 50 SDS air compressor, bailing drum, 24’ kelly, 8-1/4” retractable table, hydraulic pulldown, air clutches, mounted on 1989 Chevy Topkick with Cat 3208T, rod box, 300’ of 3” drill stem, tools, well maintained  Price:  $47,500  Additional pipe available at extra cost.

EWBANKS 50(Ref#13911Ra)  4 x 5 mud pump, mounted on 1978 International single axle truck, Cat 3208 engine, PTO, 5-1/4” stationary rotary table, no air, square kelly, mud pan, pipe rack, 200’ pipe  Price:  $37,500

Built 1986, mounted on 1986 GMC Brigadier truck with Cat 3208 engine, Ford 4 cylinder Industrial deck engine, 5 x 6 mud pump, 1 mainline winch, 1 sandline winch with free fall, sitting outside for a while, was in proper working condition when parked Price on Request

Manufactured 1973, 871 Detroit diesel on deck, 450 cfm Bendix Westinghouse air compressor, no mud pumps but hydraulics are there, 4” kelly, 8” retractable table, bailing line, mounted on 1972 Ford F900 tandem axle truck with 434 gas engine, 3 hydraulic jacks, 200’ of 4-1/2” x 15’ drill pipe, sitting since 2019  Price:  $37,500

4 cylinder Ford diesel engine on deck, 38" hydraulically raised mast, 5-1/2" table retractable to 18" x 12" deep, 3-1/2" x 20" fluted Kelly, drill line drum, sandline drum and casing drum (no line on rig).  2-part block, shock in the crown for cable drilling,  Mounted on 1992 Ford L7000 all-wheel drive truck with 6 cyl Ford diesel engine, automatic transmission with big hydraulic pump, low miles, 3 hydraulic leveling jacks, needs new hoses and swivel.  Price:  $32,500 - Oklahoma

CYCLONE 35R(Ref#6558T)  5” Gardner Denver mud pump with 3 cyl diesel engine, no air, square kelly, retractable table, hydraulic pulldown, pipe rack, 4 cylinder diesel deck engine, mounted on 1985 Mack twin screw with diesel engine, 3 hyd leveling jacks, 300’ of 2” x 16’ drill pipe  Price:  $64,500

Built 1966, 5 x 6 mud pump, developmental air compressor, mounted on 1966 Ford F950 Super Duty with gas engine, (2) gas deck engines (one runs rig, one runs air compressor and mud pump), 240’ drill rod, 15’ sub and bit  Price:  $29,500

Built 1980’s, trailer mounted, new swivel, 420cc engine, 250’ – 500’ depth, 30 gpm hydraulic pump (newer hoses), 2000# electric winch, 2” mud pump, 2 gpm mist pump, 250’ of 10" drill pipe, 2 drill collars, tooling, bit, subs,.  180 cfm Sullair compressor, water tank/pipe trailer  Price:  $46,500

Built new 74 HP Kohler Tier 4 Turbo diesel industrial deck engine, Industrial Permco dual 28 gpm main pump w/vari speed split driver circuits in volve controls, 3 x 2” MCM Model 118 mud pump 350 gpm/95 psi, 150 rpm main drill head 1000 ft/lb torque, 55 gal hyd reservoir, 12,000# push/pull force w/chain hoist drive, 16’6” tubular 4x6 mast 12’ stroke, designed for 10’ Mayhew Jr drill pipe, 82000 BTU hydraulic oil cooler, swivel with extreme duty 18,000# twin thrust bearing set and shevron seals w/changeable ware sleeves, hydraulicuniversal breakout system, swing away drill head, ½” minimum watercourse through all piping, 22 gallon fuel tank, 20’ of 3” charge line, 20’ of 2” bypass hose w/cam locks, 12 volt primer and wash down pump, removable drill pipe guide, 1200# hydraulic accessory host telewscoping to 22’ height for casing work w/drill pipe tool for lifting and handling drill stem.  Weight (skid mounted unit):  6500 lbs., dimensions (trailer mounted) 110” long x 90” wide (will fit in 20’ shipping container)  Price, skid mounted:  $59,500  Price, trailer mounted:  $69,500

Preferred Pump offers the best rewards program in the water well equipment industry. Check out our social media pictures to see what you"ve been missing!

Preferred Pump offers the best rewards program in the water well equipment industry. Check out our social media pictures to see what you"ve been missing!

The Baoji/Bomco F1000 Triplex mud pump has a max. working pressure of 5,000PSI and a 6-3/4" liner size. This model is the first choice for the medium and deep dr... More Info

The Baoji/Bomco F1600HL Triplex mud pump has a max. working pressure of 7,5000PSI and a displacement of 46.5L/S with 6" liner size. This model is the f... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Emsco/Bomco 1600 Mud Pump, Unitized 1600 Mud Pump Powered by Two GE 752 Motors Charging Pump, Liner Flush Pump, Relief Valve, Mud Gauge, Etc. ....Call For Price More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - 1 - Rebuilt Gardner Denver PZ-9 Mud Pump Package, New Caterpillar C-27, 1050 HP diesel engine. Belt-driven. comes with pulsation dampener, discharge block, precharge, li... More Info

Mud Pumps - 1 of 3 used Gardner Denver PZ-8 triplex mud pumps. This would be a good rebuildable core. We also have new, rebuilt and good used pumps and packages available for sale ... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Explore a wide variety of rotary mud pump on Alibaba.com and enjoy exquisite deals. The machines help maintain drilling mud circulation throughout the project. There are many models and brands available, each with outstanding value. These rotary mud pump are efficient, durable, and completely waterproof. They are designed to lift water and mud with efficiency without using much energy or taking a lot of space.

The primary advantage of these rotary mud pump is that they can raise water from greater depths. With the fast-changing technology, purchase machines that come with the best technology for optimum results. They should be well adapted to the overall configuration of the installation to perform various operations. Hence, quality products are needed for more efficiency and enjoyment of the machines" full life expectancy.

Alibaba.com offers a wide selection of products with innovative features. The products are designed for a wide range of flow rates that differ by brand. They provide cost-effective options catering to different consumer needs. When choosing the right rotary mud pump for the drilling project, consider factors such as size, shape, and machine cost. More powerful tools are needed when dealing with large projects such as agriculture or irrigation.

Alibaba.com provides a wide range of rotary mud pump to suit different tastes and budgets. The site has a large assortment of products from major suppliers on the market. The products are made of durable materials to avoid corrosion and premature wear during operations. The range of products and brands on the site assures quality and good value for money.

Explore the various mud rotary drill rig products available for wholesale at Alibaba.com. Get a mud rotary drill rig for drilling water wells, water exploration holes, geological exploration, coal mines, and other kinds of mining. Some mud rotary drill rig options use caterpillar tread to move. Others use rubber tires, while others require a separate means of transport. Caterpillar tread propulsion can climb up to 25 degrees inclination. Some products in the range are capable of drilling over 200 meters, while others are only used for open-pit mining with depths of around 3 meters. Drilling can be done vertically downwards, horizontally, or in a slanting direction. Drilling speed depends on the power of the machine and the general hardness of the surface. The hole diameter can vary from 90mm to 200mm.

mud rotary drill rig options also include an air compressor, a mud pump, drilling rods of various sizes, connectors, and a drilling tower. Drilling is done using drill bits of various shapes, sizes, and compositions. You can choose between diamond bits, alloy ring-shaped bits, 3-wing alloy bits, PDC bits, and hammer bits. Each drill bit uses different drilling methods, including rotary, percussion, blast hole, and core drilling.

Smaller products have a lifting power of around 25 kilonewtons and weigh about 2,500kgs. They’re ideal for small-scale drillings such as farms and homes. Larger ones are faster with more power, making them ideal for commercial use. Browse through Alibaba.com and find a mud rotary drill rig that’s ideal for your work scope. Buy mine drilling rigs for your wholesale business at competitive prices. Chinese wholesalers provide you with customization options and great after-sales services.

A fast and efficient method of drilling, mud rotary drilling is effective in a wide range of geological formations, including sand, silt, clay, gravel, cobbles, and boulders. Not hindered by the presence of groundwater, a mud drill is also used for coring bedrock.

With the necessary torque for powerful rotation, new and seasoned operators find the Geoprobe® line of geotechnical drilling rigs and combination drilling rigs make for an effective mud drill thanks to:

With rig service shops in Pennsylvania, Kansas, and Florida, you’ll have industry-leading drill rig service support nearby for your routine maintenance or more in-depth rig remounting and refurbishment work - keeping your mud drill in the field earning dollars. Our service technicians are backed by our team of engineers to ensure solutions not bandaids to issues. And our production processes mean your mud drill is constructed consistently and tested thoroughly to ensure easier service support.

Engineered with efficiency and ease in mind, investing in a Geoprobe® mud drill simplifies your sampling while reliably ramping up production and rig utilization rates.

Our team of engineers thrives on collaborating with drillers while they continually innovate new designs for our mud drill line. Our goal is to make your job faster, safer, and easier. Partner with us and we"ll work to decrease your mud drill downtime while increasing your family time.

The effectiveness of triplex mud pumps for sale determines the success of drilling operations in rigs. Circulation of the drilling fluid or mud is a continuous process that calls for uninterrupted operations of the mud pumps. Finicky about how our equipment work, we at ShalePumps, go to extreme lengths before engineering modern beasts for continuous drilling operations in rigs.

Our state of the art Houston facility develops high performing mud pumps for drillings rigs by a combination of the best materials, and structural dynamics to put together some of the best equipment. Designed to be adapted for various drilling applications in rigs through designs that incorporate various liner sizes, the triplex mud pumps for sale that leave the assembly line at ShalePumps are mean and mighty workhorses. The triplex mud pumps feature high performance steel power ends, balanced forged steel crankshaft, steel herringbone gears and anti-friction roller bearings. Striking the right balance between weight and performance, the triplex mud pumps for sale we make are best for drilling operations in rigs.

The triplex mud pumps manufactured at ShalePumps have extended continuous duty cycles, and foolproof lubrication systems for smooth drilling operations in rigs. With mud pumps from ShalePumps the drilling operations in rigs will never be the weak link, but a pivot that spells success.

ShalePumps, LLC is proud to introduce the SP-1614 1600 HP Continuous Duty Triplex Drilling Pump. Engineering and rated for 1600 horse power at 110 strokes per minute with a 14” stroke capable of 7500 PSI. Manufactured in our Houston Texas facility, this pump defines longevity, quality and capability. The SP-1614 is designed to incorporate minimum weight and maximum performance using a high performance steel power end, a balanced forged steel crank shaft, steel herringbone gears and anti friction roller bearing throughout. Multiple liner sizes are available to allow variance in pressure and output volume for a variety of drilling applications. Download the performance chart for more detailed information.

It’s time for piston mud pumps to enter the 21st century. Centerline Mud Pumps utilize common, industry-proven, and easily obtained fluid end parts. Designed to give you better flow capacity, pressure, size and weight advantages, that you won’t find anywhere else. Centerline Mud Pumps are built to exceed the most demanding specifications in the industry. These pumps are built to last.

Centerline Manufacturing is pleased to introduce their line of hydraulic drive mud pumps. Since 1983, Centerline Manufacturing has been involved in the design, manufacture, and production of drilling equipment, support equipment, and tooling for the water well industry. Our line of mud pumps include several new milestone technologies not found anywhere else in the industry.

Provides 150-180* GPM (Gallon Per Minute) of standard mud flow at 350 psi continuous. The 180 GPM is a provisional condition that requires the mud pressure to be below 275 psi and the hydraulic oil temperature below 165 degrees F.

Provides 300-360* GPM (Gallon Per Minute) of standard mud flow at 350 psi Continuous.  The 360 GPM is a provisional condition that requires the mud pressure to be below 275 psi and the hydraulic oil temperature below 165 degrees F.

Provides 450-540* GPM (Gallon per Minute) of standard mud flow ar 350 psi Continuous.  The 540 GPM is a provisional condition that requires the mud pressure to be below 275 psi and the hydraulic oil temperature below 165 degrees F.

The 42-year-old, family-owned American Drilling Services in Florida, relied on homemade drill rigs to complete primarily 2- to 4-inch residential water wells. With demand increasing, they began looking for newer technology in order to complete more mud pump well drilling.

“Technology is always changing. We used to drill galvanized steel with cable drilling. Now we’re exclusively rotary drilling,” said William Diaz, driller, who has been with the company for seven years. “The technology gets better, and things get easier.”

“We used to do one well per day, occasionally two. The DM250 has helped us keep up with the workload by being able to drill quicker,” Diaz said. “The pulldown power of the top head is significantly stronger than our previous rigs. With the mud pump, we can clean out the hole a lot faster, which means less waiting around.”

580 GD Compressor, 5 X 6 Mud Pump, PTO, NO Deck Engine. Rig Was Rebuilt In 2010, New 23" Kelly, New Little Giant Swivel, 2000 Rotary Table, Transfer Case Rebuilt, New 100 Pulldown Chain & New Sprockets, Bowie Inj. Pump, Hyd. Oil Cooler, New Railing On Derrick For Swivel Drives, Mud Pit, 200" Of 2 More Info »

256S2 Leroi Compressor, 5 X 6 GD Mud Pump, PTO, NO Deck Engine. Tophead Drive, Retractable Table, Aux. Lift Line, Sandline, Three Part Main Line, (3) Hyd. Jacks, Weldco Beales Casing Hammer Package Available At Additional Cost. Mounted On 79 4-Axle CCC W/ 290 Cummins. Good Condition.

256S2 Leroi Compressor, 8V71 Detroit Deck Engine. Tophead Drive, Rebuilt Head, New Main Gear In Transfer Case W/ Chain Inspection, Casing Handling Cylinder W/ Sheaves, Bean Water Pump, 60K LB. Hoisting Drums, 2 Part Block, Weldco-Beales Casing Hammer, Rock Oiler, New Drive Compressor, Drive Line & U-Joint, (3) Hyd. Jacks, Hydrostatic Clutches. Mounted On 73 More Info »

275 Joy Compressor, 5 x 6 Mud Pump, PTO, NO Deck Engine. (3) Hyd. Jacks, 2 Speed Hyd. Tophead, Hyd. Oil Cooler, Single Rod Loader, Braiden Main Winch, Secondary Hyd. Winch, 360" Of 2 3/8" x 20" Rod, All Hand Tools, 150" Of 2 3/8" X 15" Rod, Pipe Rack & Toolboxes, Truck Engine Needs More Info »

7 1/2 X 10 G/D Mud Pump, Waukesha Diesel Deck Engine. 32" Mast, 8" Retractable Table, 20" Opening In Table, 23" Kelly, Easy Set-Up Screw Jacks. Mounted On Single Axle Trailer. Good Condition.

256S2 Leroi Compressor, 6V71 Detroit Deck Engine. Tophead Drive, (3) Hyd. Jacks, Bean Inj. Pump, Rock Oiler, Twin Disc Clutches, 60K LB. Hoisting Drum, Weldo-Beales Casing Driver. Mounted On 67 Int"l Paystar, w/ Gas. Good Condition.

5 X 6 GD Mud Pump. Hyd. Jacks, (2) Winches, 3L8 Moyno Pump, Toolboxes & Auger Rack, Deck Mounted Hyd. Drive 2,000 Psi Steam Cleaner / Power Washer. Mounted On 90 International 4900 6 X 4, w/ DT 466 245 HP. Good Condition.

5 X 6 Mud Pump, PTO, NO Deck Engine. 3 Speed Stationary Rotary Table, Water End On Pump Needs Gone Through, 23" Kelly, 200" Of Drill Pipe, Drawdown Not In Operation But Can Be Used, 2 Speed Rearend In Truck. Mounted On GMC, w/ V671 Detroit. Good Condition.

471 Detroit Deck Engine. 58" Derrick, 35" X 4" Kelly, Double Drum Drawworks Rebuilt In 2010, Drilling Platform & Side Walk Ways W/ Guard Rails, 7 1/2" Rotary Table Rebuilt In 2011, Air Clutches, Front & Rear Leveling Jacks, Derrick Lifting Cylinders Rebuilt In 2010, Rebuilt Driveline W/ New Clutch Pads In 2010, Deck Engine More Info »

(2) 425/250 Compressor, (2) 8V71 Detroit Deck Engine. (3) Hyd. Jacks (Cylinders Rebuilt 2011), 6 Rod Carousel, 30 GPM Myers Water Pump, (2) 90 Gallon Fuel Tanks, (2) Hot Boxes, (1) Compressor Rebuilt W/ No Hrs., Is Stuck From Sitting, 2nd Compressor Has Approx. 3 Yrs. Run Time On It, (1) Deck Engine Has Approx. More Info »

825/325 GHH Compressor, 3406 Cat Deck Engine. Deck Engine Rebuilt W/ Approx. 1,000 Hrs. Run Time, Less Than 10,000 Miles On Carrier Engine, New Cooler, New Main Pump, Pulldown Cylinders Rebuilt, Winch Rebuilt, (3) Hyd. Jacks, Jib Boom, Rod Rack, 6 Rod Carousel, Hammer Oiler, Water Injection Pump, 150" Of 4 1/2" X 25" Drill More Info »

256S2 Leroi Compressor, 5 X 6 GD Mud Pump, 318 Detroit Deck Engine. 10" Retractable Table, Rod Rack, 37" Derrick, (3) Hyd. Jacks, New Kelly Bar, Hydro-Frac Pump, 5 Speed Rotary Transmission, Cable Drawworks, 9 GPM Bean Water Injection Mud Pit, 500" Of 4 1/2" X 2 7/8" IF Drill Pipe, 20K LB. Front Axle, More Info »

Parco 131" X 550,000 Static Hook Load Mast, OIME SL-5 Drawworks W/ (2) 520 HP Cat Engines, Allison 606L Transmission, WPT 4-24 Water Brake, Parco 18.5" Split Level Substructure, 10X30" Doghouse, (2) Weatherford MP9 Triplex Mud Pumps W/ 398 Cat Engine, (2) 5X6 Centrifugal Chase Pumps, 2 Pit 900 Barrel Mud System, 27 1/2" Rotary More Info »

Mission Mud Pump, 8 Cyl. Diesel Deck Engine. Tophead Drive Machine, Runs 10" Drill Pipe, Rig Is Straight, Will Need Minor Repairs From Sitting, Includes 300" Of Drill Pipe, Extra Deck Engine. Mounted On 1989 Ford L7000, w/ Diesel. Good Condition.

5 1/2 X 8 Mud Pump, PTO, NO Deck Engine. Range II Derrick, Double Drum, 8" Retractable Table, Centrifugal Charge Pump, Hyd. Rod Spinner, Hyd. Chain Pulldown, Air Clutches, Weight Indicator, Racking Board, 25 Ton Block, Service Winch, Cathead, (4) Hyd. Jacks, (2) New Front Jacks, Mud Pump Rebuilt, Gearboxes Rebuilt, Includes 3 6" Drill More Info »

350 Cummins Deck Engine. 31" Brakes, Jaw Clutches, Hydrostatic Rotary Table, Drawworks Rebuilt, Cathead, Set Of Tongs, No Derrick. Mounted On Trailer.

750/250 Compressor, 8V92 Detroit Deck Engine. (3) Hyd. Jacks, Rod Rack, Inj. Pump, 240" Of 4 1/2" Drill Pipe, (2) Hammers, Standard Hand Tools, Wrenches, Odex System. Mounted On 1982 International. Good Condition.

5 X 6 Mud Pump, PTO, NO Deck Engine. Retractable Rotary Table, Chain Pulldown, (3) Hyd. Jacks, Rod Rack, Manual Clutches, Mounted On 1977 Ford, w/ Diesel.

25 HP 3 Phase 220 Volt W/ Electric Motor, 3 Speed Transmission, New Clutch, Rebuilt N Rod Head & Interchangeable A Rod Head, Both Have New Face Gears, Manual Chucks, Wireline Winch, 20 GPM Bean Pump, New Modern Hydraulics, 250" Of Electric Cable On Spool Rack W/ Waterproof Cable Connectors, Multiple Towers Including Tower For More Info »

Piston Compressor, 4 X 3 Mud Pump, 671 Detroit Deck Engine. Deck Engine Rebuilt In 2009, New King Swivel & Winch In 2013, (3) Hyd. Jacks, Rod Rack, Includes 350" Of 4 1/2" Drill Pipe, 120" Of Drill Pipe That Needs Straightened, New 8 3/4" Bit, 4 3/4" Button Bit, Subs, Lots Of Extra Parts More Info »

GD Compressor, 5 X 6 Mud Pump, PTO, NO Deck Engine. Manual Clutches, 7 1/2" Stationary Table, Rod Rack, Pulldown, (2) Hyd. Jacks, 200" Of 2 7/8" Drill Pipe, Mounted On 1991 Mack, w/ Mack Diesel. Good Condition.

Rebuilt Engine & Transmission, New Drive Lines, Rear Axles New, Main Drum Bearing New, New Hyd. Pump, New Starter, New Brake Pads On Main & Sandline Drum, New Clutch Control, New Drill Line, Mounted On CCC. Good Condition.

5 X 6 Mud Pump, PTO, NO Deck Engine. (4) Hyd. Jacks, Hyd. Pulldown, Rebuilt 5 1/4" Rotary Tabl