southwest mud pump module manufacturer

The L-shaped two-piece fluid-end was adopted into the market over 35 years ago because it was an obvious improvement over one-piece modules. Since the suction module is separate from the discharge module, it is possible to replace the suction module when it wears out instead of replacing the entire fluid end.

Southwest’s L-shaped fluid-end is manufactured from heat-treated 4130 forgings and equipped with our quick-change valve cover system; our L-shaped modules offer unmatched performance.

The market demand for 7500 psi land drilling has continued to increase and is forecasted to remain strong as drillers and operators seek to complete wells more faster and more efficiently. Southwest Oilfield Products has the expertise and ability to convert existing 5000 psi pump systems with our 7500 psi fluid end upgrade. In addition to replacing the existing valve-over-valve module with our proven L-Shaped design, a typical conversion also includes an upgraded liner retainer system, discharge cross/ strainer, and high-pressure discharge Mud Pump with Southwest L-Shaped Fluid End Modulesmanifold and 7500 psi pulsation dampener.

Updated performance data sheets that reflect the higher working pressures are provided for all upgrades performed by Southwest Oilfield Products. To ensure pump operation integrity, rod load limitations are strictly adhered to.

Premium"s high-strength, triple reduction, forged steel triplex fluid end modules are made from 4130 alloy steel, heat treated for a long working life, machined to perfection and packaged for delivery with anti-corrosion protection. The precision-made jewelry, like the exterior finish, reflects the superior quality inside.

The market demand for 7500 psi land drilling has continued to increase and forecasted to remain strong as drillers and operators seek to complete wells more faster and more efficiently. Premium has the expertise and ability to convert existing 5000 psi pump systems with our 7500 psi fluid end upgrade. In addition to replacing the existing valve-over-valve module with our proven L-Shaped design, a typical conversion also includes an upgraded liner retainer system, discharge cross/ strainer, high-pressure discharge manifold and 7500 psi pulsation dampener.

Direct replacement for the current 7500 psi wide body module (same outside dimensions and same external and internal components except valve cover, bore seal and Falcon spring retainer)

BOMCO/Emsco Mud Pumps:F2200HL, F1600HL, F-1300, F-1600, FB1300, FB1600, F-800, F-1000, F-500, F-350, DB-550, DA-700, FA-1600/1300, FC-2200, D-300/500, D-375, D-700,

Manufacturer of mud pump systems and premium well servicing equipment. The company designs and produces mud pump products which include fluid end modules, pistons, liners, and other related products used during onshore and offshore drilling of oil and gas wells to major drilling companies across the globe. It"s servicing equipment division focuses on the manufacturing of new equipment used in well completion, stimulation, and intervention such as frac pumpers, coil tubing, nitrogen and snubbing units.

Our MissionSouthwest Oilfield Products (SWOP) is committed to delivering thehighest quality products, on time, and creating positive significantimpacts on our customers projects. We strive to maintain ourinnovative stance in the industry while partnering with our customersto share the focus on generating solutions.

2012 Research and Development of High Pressure High Temperature Consumables 2013 Introduced Module Service Tool Kits Research and Development of Frac Pump Consumables

INNOVATIVE ENGINEERINGImprovements in material technology, failure analysis, machining tolerances,surface finishes, heat treating techniques, surface coatings, forgingtechnology, welding practices and assembly techniques are constantlypursued by our engineering staff for integration into our products. This pursuitcombined with over 65 years of manufacturing expertise places SWOP at theleading edge in mud pump fluid-end and expendables design.

Southwest Oilfield Products utilizes the latest engineering design toolsavailable to employ technological advances into our time-proven productdesigns. Our engineering staff utilizes SolidWorks Premium for 3D CADand SolidWorks Simulation Premium for finite element analysis. We havestrengthened our non-destructive testing techniques and manufacturingmethods through involving our engineers in the hands-on inspection andevaluation of our products.We emphasize a seamless interface between our Design EngineeringDepartment and our Manufacturing Engineering Department. Our designengineers are frequently involved in the shop floor activity. Similarly, ourmachine programmers play a prominent role in product improvements andFinite element analysis of a

HIGH QUALITY FLUID-END COMPONENTSSince 1947, Southwest Oilfield Products,SWOP has been an independent OEMmanufacturer and supplier of qualityfluid-end replacement parts. Below isan illustration of a typical Fluid-Endcomponent offering from SWOP.

Southwest Oilfield Products, has been a pillar in the OilfieldIndustry since 1947. From our Houston based manufacturingfacility, we strive to maintain our legacy by offering the highestquality parts & service the industry deserves.

THE ORIGINAL L SHAPED FLUID-ENDOften Imitated But Never Duplicated, Southwest Oilfield Products 2-Piece LShaped Fluid-Ends Have Become The Recognized Standard.The L-shaped two piece fluid-end was adopted into the market over 35 years ago because it was an obviousimprovement over OEM style (valve-over-valve) modules. Since the suction module is separate from the dischargemodule, it is possible to replace the suction module when it wears out instead of replacing the entire fluid-end.

SWOPs L Shaped Fluid-End Is Manufactured From Heat-Treated 4130 ForgingsAnd Equipped With Our Quick-Change Valve Cover System, Our L-Shaped ModulesOffers Unmatched Performance.Southwests second-to-none manufacturing is backed by the best warranty on the market.

HP QUICK-CHANGE VALVE COVERSouthwest Oilfields HP Quick-Change ValveCovers eliminate the need to replace or repairthe expensive parts of your valve cover assembly.Only Southwest Oilfields HP Quick-Change ValveCovers provide true steel-to-steel tightening andhas the best valve cover seal on the market.Most pumps require no modification to convertto our Quick-Change product. Simply remove allcomponent parts of the old valve cover includingstuds. Southwests assembly kit includeseverything needed for the changeout.

BONDED VALVE AND FULL OPEN SEATSouthwest Oilfield Products full open valve with bonded insert hasreplaced the slip-on insert valves. This design is permanently bonded tothe valve body; it reduces the tendency for fluids to penetrate between thepolyurethane insert and the valve body, thus preventing premature failure.The full open design of the valve seat is far superior to webbed style seats formany reasons:

BullDog PistonIntroduced in 2014, the BullDog piston is engineered forhigh temperature and pressure service (300F / 7500PSI). The BullDog piston is suitable for a wide variety ofdrilling muds including oil, synthetic and water-based.Along with its rugged and reliable design, a special blendof lubricating agents enhances the running life of thispiston. Reducing operating costs in extreme drillingenvironments is a key benefit of the BullDog piston.

Triplex Grayloy LinersFor use in todays higher pressure and faster strokingtriplex pumps, Grayloy liners are made of the highestquality high chrome premium alloy steel. They aremanufactured to provide maximum runs at minimal cost.

Southwest Quick-Change HydraulicLiner RetainerIncreased safety and faster change-outs is the hallmarkof Southwest Oilfields Quick-Change Hydraulic LinerRetention System. Our patented design eliminates theneed for hammers and wrenches without compromisingsealing or alignment of the liner.

HIGH QUALITY CONSUMABLESSouthwest Washpipe And PackingOur premium washpipes are manufactured for all swivelsto precise tolerance with the same superior wear-resistantsurface as the Grayloy piston rod.High-quality fabric and rubber molded wash pipe packingis also available.

Packing And Gaskets For TriplexAnd Duplex PumpsSouthwest Oilfield Products offers a wide range ofgaskets and packing materials for use in drilling pumps.Gaskets are made of various elastomers and rubbersdepending on the application. New high temperatureelastomers are now available.

PISTON RODS AND CLAMPSPiston RodsThe SWOP piston rod incorporates the Grayloy longerwearing surface to provide the best piston rod for yourtriplex or duplex pump.

Southwest Duplex Bonded Fail-Safe PistonThis duplex piston gives excellent service in both oil andwater base muds. The fail-safe fluid expanded lip is notdamaged by high pressure and fast pump strokes.

Southwest Duplex Grayloy Piston RodsHigh quality Grayloy material is used on all Southwestduplex piston rods. This corrosion-resistant, high density,long-wearing surface results in fewer packing changesand longer life for gland bushings and junk rings.

GLOBAL SERVICE SOLUTIONSOnsite Service Solutions Offered (Domestic & International)Our SWOP Field Service Team is committed to providing customers with highly trained personnelwho can thoroughly inspect fluid-ends and troubleshoot mud pump fluid-end issues. Our servicesare designed to provide customers with valuable information about the state of their fluid-endsand fluid-end components including:

Laser Alignment SystemAs part as Southwest Oilfields Service and repair department the Zero-N Laser Alignment System isutilized to provide the most accurate fluid-end alignment service available. The Zero-N Laser is accurateto within 0.001 in both the X and Y axes with a digital readout for consistent, repeatable measurements.The system is lightweight and suitcase portable, eliminating difficult transportation issues. Alignmentinspections can be performed worldwide by our team of trained service technicians.

F550 Service TruckWith the addition of a fully-tooled,heavy-duty service truck, our Southwestservice offerings continue to grow!With a 6,000 lb. lift capacity, onboardwelding unit and pneumatic tool systemthis vehicle is equipped to handle eventhe most challenging, on-site fluid-endprojects.

Manufacture of Mud Pump FluidEnds & Expendables10340 Wallisville RoadHouston, Texas 77013Phone (713) 675-7541Toll Free (800) 392-4600Fax (713) 675-5206

AloStar Business Credit has provided a $15 million senior secured revolver and a $2 million equipment term loan to Southwest Oilfield Products (“Southwest”), a manufacturer of mud pump solutions and premium well servicing equipment. The company’s corporate offices and primary manufacturing facility are located in Houston, Texas with warehouse and distribution facilities located throughout the U.S.

Founded in 1947, Southwest’s mud pump division focuses on mud pump products which include fluid end modules, pistons, liners, and other related products used during onshore and offshore drilling of oil and gas wells. Additionally, the well servicing equipment division focuses on the manufacturing of new equipment used in well completion, stimulation, and intervention such as frac pumpers, coil tubing, nitrogen and snubbing units.

“Southwest Oilfield Products has consistently been a premier producer of high-quality mud pump solutions,” said Andy McGhee, president of AloStar Business Credit. “Over the next five years we expect to see them continue their growth trajectory alongside the market growth in this industry.”

Southwest is well positioned to take advantage of the recent energy renaissance that has begun in the U.S. According to a 2012 report from the U.S. Energy Information Administration, the U.S. is slated to become the world’s top producer of oil by 2020, a net exporter of oil around 2030, and nearly self-sufficient in energy production by 2035.

“AloStar is a good fit with our current growth perspective,” said Paul DeWeese, CEO of Southwest Oilfield Products. “We are delighted that AloStar could provide capital for us as we implement our initiatives to help our growth over the next several years.”

Southwest Oilfield Products, Inc. is a premier oil and gas equipment manufacturer providing innovative mud pumping solutions and well service systems to the world’s leading oil and gas exploration and production companies.

Our MissionSouthwest Oilfield Products (SWOP) is committed to delivering thehighest quality products, on time, and creating positive significantimpacts on our customers projects. We strive to maintain ourinnovative stance in the industry while partnering with our customersto share the focus on generating solutions.

2012 Research and Development of High Pressure High Temperature Consumables 2013 Introduced Module Service Tool Kits Research and Development of Frac Pump Consumables

INNOVATIVE ENGINEERINGImprovements in material technology, failure analysis, machining tolerances,surface finishes, heat treating techniques, surface coatings, forgingtechnology, welding practices and assembly techniques are constantlypursued by our engineering staff for integration into our products. This pursuitcombined with over 65 years of manufacturing expertise places SWOP at theleading edge in mud pump fluid-end and expendables design.

Southwest Oilfield Products utilizes the latest engineering design toolsavailable to employ technological advances into our time-proven productdesigns. Our engineering staff utilizes SolidWorks Premium for 3D CADand SolidWorks Simulation Premium for finite element analysis. We havestrengthened our non-destructive testing techniques and manufacturingmethods through involving our engineers in the hands-on inspection andevaluation of our products.We emphasize a seamless interface between our Design EngineeringDepartment and our Manufacturing Engineering Department. Our designengineers are frequently involved in the shop floor activity. Similarly, ourmachine programmers play a prominent role in product improvements andFinite element analysis of a

HIGH QUALITY FLUID-END COMPONENTSSince 1947, Southwest Oilfield Products,SWOP has been an independent OEMmanufacturer and supplier of qualityfluid-end replacement parts. Below isan illustration of a typical Fluid-Endcomponent offering from SWOP.

Southwest Oilfield Products, has been a pillar in the OilfieldIndustry since 1947. From our Houston based manufacturingfacility, we strive to maintain our legacy by offering the highestquality parts & service the industry deserves.

THE ORIGINAL L SHAPED FLUID-ENDOften Imitated But Never Duplicated, Southwest Oilfield Products 2-Piece LShaped Fluid-Ends Have Become The Recognized Standard.The L-shaped two piece fluid-end was adopted into the market over 35 years ago because it was an obviousimprovement over OEM style (valve-over-valve) modules. Since the suction module is separate from the dischargemodule, it is possible to replace the suction module when it wears out instead of replacing the entire fluid-end.

SWOPs L Shaped Fluid-End Is Manufactured From Heat-Treated 4130 ForgingsAnd Equipped With Our Quick-Change Valve Cover System, Our L-Shaped ModulesOffers Unmatched Performance.Southwests second-to-none manufacturing is backed by the best warranty on the market.

HP QUICK-CHANGE VALVE COVERSouthwest Oilfields HP Quick-Change ValveCovers eliminate the need to replace or repairthe expensive parts of your valve cover assembly.Only Southwest Oilfields HP Quick-Change ValveCovers provide true steel-to-steel tightening andhas the best valve cover seal on the market.Most pumps require no modification to convertto our Quick-Change product. Simply remove allcomponent parts of the old valve cover includingstuds. Southwests assembly kit includeseverything needed for the changeout.

BONDED VALVE AND FULL OPEN SEATSouthwest Oilfield Products full open valve with bonded insert hasreplaced the slip-on insert valves. This design is permanently bonded tothe valve body; it reduces the tendency for fluids to penetrate between thepolyurethane insert and the valve body, thus preventing premature failure.The full open design of the valve seat is far superior to webbed style seats formany reasons:

BullDog PistonIntroduced in 2014, the BullDog piston is engineered forhigh temperature and pressure service (300F / 7500PSI). The BullDog piston is suitable for a wide variety ofdrilling muds including oil, synthetic and water-based.Along with its rugged and reliable design, a special blendof lubricating agents enhances the running life of thispiston. Reducing operating costs in extreme drillingenvironments is a key benefit of the BullDog piston.

Triplex Grayloy LinersFor use in todays higher pressure and faster strokingtriplex pumps, Grayloy liners are made of the highestquality high chrome premium alloy steel. They aremanufactured to provide maximum runs at minimal cost.

Southwest Quick-Change HydraulicLiner RetainerIncreased safety and faster change-outs is the hallmarkof Southwest Oilfields Quick-Change Hydraulic LinerRetention System. Our patented design eliminates theneed for hammers and wrenches without compromisingsealing or alignment of the liner.

HIGH QUALITY CONSUMABLESSouthwest Washpipe And PackingOur premium washpipes are manufactured for all swivelsto precise tolerance with the same superior wear-resistantsurface as the Grayloy piston rod.High-quality fabric and rubber molded wash pipe packingis also available.

Packing And Gaskets For TriplexAnd Duplex PumpsSouthwest Oilfield Products offers a wide range ofgaskets and packing materials for use in drilling pumps.Gaskets are made of various elastomers and rubbersdepending on the application. New high temperatureelastomers are now available.

PISTON RODS AND CLAMPSPiston RodsThe SWOP piston rod incorporates the Grayloy longerwearing surface to provide the best piston rod for yourtriplex or duplex pump.

Southwest Duplex Bonded Fail-Safe PistonThis duplex piston gives excellent service in both oil andwater base muds. The fail-safe fluid expanded lip is notdamaged by high pressure and fast pump strokes.

Southwest Duplex Grayloy Piston RodsHigh quality Grayloy material is used on all Southwestduplex piston rods. This corrosion-resistant, high density,long-wearing surface results in fewer packing changesand longer life for gland bushings and junk rings.

GLOBAL SERVICE SOLUTIONSOnsite Service Solutions Offered (Domestic & International)Our SWOP Field Service Team is committed to providing customers with highly trained personnelwho can thoroughly inspect fluid-ends and troubleshoot mud pump fluid-end issues. Our servicesare designed to provide customers with valuable information about the state of their fluid-endsand fluid-end components including:

Laser Alignment SystemAs part as Southwest Oilfields Service and repair department the Zero-N Laser Alignment System isutilized to provide the most accurate fluid-end alignment service available. The Zero-N Laser is accurateto within 0.001 in both the X and Y axes with a digital readout for consistent, repeatable measurements.The system is lightweight and suitcase portable, eliminating difficult transportation issues. Alignmentinspections can be performed worldwide by our team of trained service technicians.

F550 Service TruckWith the addition of a fully-tooled,heavy-duty service truck, our Southwestservice offerings continue to grow!With a 6,000 lb. lift capacity, onboardwelding unit and pneumatic tool systemthis vehicle is equipped to handle eventhe most challenging, on-site fluid-endprojects.

Manufacture of Mud Pump FluidEnds & Expendables10340 Wallisville RoadHouston, Texas 77013Phone (713) 675-7541Toll Free (800) 392-4600Fax (713) 675-5206