suction manifold 12p160 mud pump drawings factory

These workhorses keep the mud flowing and your rig running. If theyʼre not working, youʼre not working. We make everything from the crankshaft to the liner seal to the skid. Each one is precision engineered for your rig so you can get back to turning.

NOV 12-P-160 Mud Pump is rated at 1600 input horsepower (1193 kw) at 120 strokes per minute, with a 12-inch (304.8 mm) stroke. Multiple liner sizes allow pressures and volumes to handle circulation requirements in deep drilling applications.

Flexibility: Compact engineering provides higher efficiency in less space. The NOV 12-P-160 Triplex Mud Pump light weight and flexible design make it easily adaptable to a variety of rig configurations. This provides flexibility as drilling requirements and conditions change.

Fluid End Modules: NOV offers a choice of fluid end modules and valve covers for every P Series pump model to select the fluid end module that exactly matches drilling requirements. All pump models can be equipped with either the standard or premium forged, two-piece interchangeable fluid modules

The Oilfield Equipment related post NOV 12-P-160 Triplex Mud Pump Used [AE] is from Flowtech Energy. Looking for Oilfield Equipment including New, Used, Remanufactured and Surplus Oilfield Supply, check out our inventory or call our toll free number at 877-645-6693 for more information.

Author: Robert Coull Ref: Q_8001/GJ-204-016 Drilling Rig SattiCheck By: John Guy Upgrade No 2 & No 3 Mud Pump Date: 28-NOV-2019

1. Introduction, Background and Summary This scope of work covers the upgrade required to be completed on mud pump No 2 & No 3 to increase the operational performance from 5K to 7.5K operational limits.

M991000167-ASM-001 03 05/2015 Titan BX Valve Assembly Dwg Attached Upgrading Project of Jack UpAuthor: Robert Coull Ref: Q_8001/GJ-204-016 Drilling Rig SattiCheck By: John Guy Upgrade No 2 & No 3 Mud Pump Date: 28-NOV-2019

7,500 Psi discharge manifold cross strainers 12 – 16 Weeks 1 Dual 7,500 Psi discharge manifolds (From 1st Aug) Valve seat & spring assemblies

• Disconnect & remove suction stabilizer • Disconnect & remove suction extension • Disconnect & remove suction PRV • Remove suction manifold

• Remove reset relief • Disconnect & remove reset relief / blead off line spool at pump & blead off valve. Upgrading Project of Jack UpAuthor: Robert Coull Ref: Q_8001/GJ-204-016 Drilling Rig SattiCheck By: John Guy Upgrade No 2 & No 3 Mud Pump Date: 28-NOV-2019

• Drain off pressure from pulsation dampener pre charge (relief valve side) • Remove pulsation dampener (relief valve side) • Disconnect & remove reset relief valve spool flange from strainer cross (relief valve side) • Remove cross assembly support (relief valve side) • Remove cross assembly (relief valve side) • Drain off pressure from pulsation dampener pre charge (mud pump discharge side) • Remove pulsation dampener (mud pump discharge side) • Disconnect & remove pressure gauge (mud pump discharge side) • Disconnect & remove pressure gauge spool flange from strainer cross (mud pump discharge side) • Disconnect mud pump discharge line • Remove cross assembly support (mud pump discharge side) • Remove cross assembly (mud pump discharge side)

• Remove intermediate rod & piston • Remove liner • Remove suction module • Remove discharge module

• Discharge connector/adapter installation • Discharge module installation • Suction module installation • Suction manifold • Discharge manifold 7.5K • Liner wear plate installation • Liner pilot bushing installation • Discharge spacer installation • Follow tightening procedure as per equipment manual

• Installation cross assembly • Installation of cross assembly support Upgrading Project of Jack UpAuthor: Robert Coull Ref: Q_8001/GJ-204-016 Drilling Rig SattiCheck By: John Guy Upgrade No 2 & No 3 Mud Pump Date: 28-NOV-2019

• Connect mud pump discharge line to cross assembly • Follow tightening procedure as per equipment manual • Installation of pressure gauge spool • Installation of pressure gauge (Model 6 – 10K) • Follow tightening procedure as per equipment manual (relief valve side) • Installation cross assembly (relief valve side) • Installation of cross assembly support • Follow tightening procedure as per equipment manual

• Install pulsation dampener (relief valve side) • Install pulsation dampener (mud pump discharge side) • Follow tightening procedure as per equipment manual for both pulsation dampeners • Fill pulsation dampener pre charge (CDC to provide required pre charge pressure requirement).

• Install liner • Fit liner clamp • Check alignment • Install piston to connecting rod • Fit piston clamp • Fit piston rod/piston assembly • Fit sub-rod to intermediate rod • Fit piston rod to sub rod • Fit piston clamp • Position & connect liner spray manifold

• Oil sample to be taken & sent for analyses • Power end inspection Upgrading Project of Jack UpAuthor: Robert Coull Ref: Q_8001/GJ-204-016 Drilling Rig SattiCheck By: John Guy Upgrade No 2 & No 3 Mud Pump Date: 28-NOV-2019

12. Testing and Commissioning All NDE and testing shall be as required by ABS and GOE Upgrading Project of Jack UpAuthor: Robert Coull Ref: Q_8001/GJ-204-016 Drilling Rig SattiCheck By: John Guy Upgrade No 2 & No 3 Mud Pump Date: 28-NOV-2019