suction manifold 12p160 mud pump drawings free sample

PAGE DRAWING NO. REV. DRAWING DESCRIPTION 1 PL 1292332 C FLUID END ASSEMBLY (STANDARD) 2 PL 1292613 -- FLUID END ASSEMBLY WITH PREMIUM MODULES 3 PL 1292737 -- FLUID END ASSEMBLY WITH H.P. MODULES 4 PL 1292000 U FLUID END ASSEMBLY (SHEET 1 OF 3) WITH TAPR-LOK VALVE COVERS 5 PL 1292000 U FLUID END ASSEMBLY (SHEET 2 OF 3) TOP VIEW OF ROD CHAMBERS 6 PL 1292000 U FLUID END ASSEMBLY (SHEET 3 OF 3) SECTION THRU ROD CHAMBERS 7 PL 1292120 D LINER SPRAY SYSTEM 8 PL 1292001 X POWER END ASSEMBLY (SHEET 1 OF 3) SECTION THRU POWER END 9 PL 1292001 X POWER END ASSEMBLY (SHEET 2 OF 3) SECTION THRU CRANKSHAFT 10 PL 1292001 X POWER END ASSEMBLY (SHEET 3 OF 3) SECTION THRU PINION AND CROSSHEADS 11 -- -- SUCTION STABILIZER ASSEMBLIES (OPTIONAL) 12 PL 1292312 G DAMPENER MANIFOLD, DOUBLE SIDE INLET (OPTIONAL) 13 -- -- DAMPENER MANIFOLD ASSEMBLIES (OPTIONAL) 14 -- -- LINER FLUSHING SYSTEM (OPTIONAL) 15 PL 1292316 -- LINER FLUSHING SYSTEM, RIGHT ANGLE DRIVE (OPTIONAL) 16 PL 1291157 B LINER FLUSHING PUMP, RIGHT ANGLE DRIVE (OPTIONAL) 17 -- -- STRAINER CROSS ASSEMBLIES (OPTIONAL) 18 -- -- TOOL AND ACCESSORIES 19 PL 1292004 E OUTLINE DRAWING

NOV 12-P-160 Mud Pump is rated at 1600 input horsepower (1193 kw) at 120 strokes per minute, with a 12-inch (304.8 mm) stroke. Multiple liner sizes allow pressures and volumes to handle circulation requirements in deep drilling applications.

Flexibility: Compact engineering provides higher efficiency in less space. The NOV 12-P-160 Triplex Mud Pump light weight and flexible design make it easily adaptable to a variety of rig configurations. This provides flexibility as drilling requirements and conditions change.

Fluid End Modules: NOV offers a choice of fluid end modules and valve covers for every P Series pump model to select the fluid end module that exactly matches drilling requirements. All pump models can be equipped with either the standard or premium forged, two-piece interchangeable fluid modules

The Oilfield Equipment related post NOV 12-P-160 Triplex Mud Pump Used [AE] is from Flowtech Energy. Looking for Oilfield Equipment including New, Used, Remanufactured and Surplus Oilfield Supply, check out our inventory or call our toll free number at 877-645-6693 for more information.

Kverneland, Hege, Kyllingstad, Åge, and Magne Moe. "Development and Performance Testing of the Hex Mud Pump." Paper presented at the SPE/IADC Drilling Conference, Amsterdam, Netherlands, February 2003. doi: https://doi.org/10.2118/79831-MS

Since the NOV A1700-PT Triplex Mud Pump was built approximately 60 years ago, the industry has widely accepted the three cylinder or triplex style pump. Triplex mud pumps are manufactured worldwide, and many companies have emulated the original design and developed an improved form of the triplex pump in the past decade.

NOV A1700-PT Triplex Mud Pumps have many advantages they weight 30% less than a duplex of equal horsepower or kilowatts. The lighter weight parts are easier to handle and therefore easier to maintain. The other advantages include;They cost less to operate

One of the more important advantages of triplex over duplex pumps, is that they can move large volumes of mud at the higher pressure is required for modern deep hole drilling.

NOV A1700-PT Triplex Mud Pump is gradually phasing out duplex units. In a triplex pump, the pistons discharge mud only when they move forward in the liner. Then, when they moved back they draw in mud on the same side of the piston. Because of this, they are also called “single acting.” Single acting triplex pumps, pump mud at a relatively high speeds. NOV A1700-PT Triplex Mud Pump has three pistons each moving in its own liner. It also has three intake valves and three discharge valves. It also has a pulsation dampener in the discharge line.

A well-placed suction stabilizer can also prevent pump chatter. Pump chatter occurs when energy is exchanged between the quick opening and closing of the reciprocating pump’s valves and the hammer effect from the centrifugal pump. Pump isolation with suction stabilizers is achieved when the charge pumps are isolated from reciprocating pumps and vice versa. The results are a smooth flow of pumped media devoid of agitating energies present in the pumped fluid.

Suction stabilizer units can mitigate most of the challenges related to pulsations or pressure surges, even in the most complex piping conditions. The resulting benefits prevent expensive unplanned downtime and decrease costs and inconvenience associated with system replacements and repairs.

NOV 12-P-160 Mud Pump is rated at 1600 input horsepower (1193 kw) at 120 strokes per minute, with a 12-inch (304.8 mm) stroke. Multiple liner sizes allow pressures and volumes to handle circulation requirements in deep drilling applications.

Flexibility: Compact engineering provides higher efficiency in less space. The NOV 12-P-160 Triplex Mud Pump light weight and flexible design make it easily adaptable to a variety of rig configurations. This provides flexibility as drilling requirements and conditions change.

Fluid End Modules: NOV offers a choice of fluid end modules and valve covers for every P Series pump model to select the fluid end module that exactly matches drilling requirements. All pump models can be equipped with either the standard or premium forged, two-piece interchangeable fluid modules