what kind of electric motor to run a mud pump quotation

15 Models below. Made in USA. Gas, Diesel or Electric diaphragm pump, or mud / sludge pump. Easily maneuverable, the gas diaphragm pump is built for performance; Ideal for seepage dewatering, high suction lift, cleaning septic tanks, pumping industrial waste and marine tanks, small wellpoint systems and dewatering in sandy, muddy waters. Honda or Briggs gasoline engine or Electric diaphragm pump with motor.

Durable design with enclosed gears in oil bath, self cleaning flow path, dry run without damage, auto priming. Built in polyurethane flapper / check valve assures self-priming to 20 feet. This unit has steel suction strainer, two NPT hex nipples and wheel kit with 10" semi-pneumatic transport wheels for portability.

Diaphragm Mud pump Suction & discharge port size cannot be reduced. Cast aluminum construction with thermoplastic rubber diaphragm. Also called a mudhog. 90 degree rotatable base on all models to fit through narrow gates. As a alternate in a centrifugal pump dredge pump design see 316F-95 2" mud pumps. Trash pumps, centrifugal Dredge Pump. Hoses and accessories.

Mud Pumps come in both electric and gas / diesel engine drive along with air motors. Most of these pumps for mud, trash and sludge or other high solids content liquid dewatering, honey wagon and pumper trucks. Slurry and mud pumps are often diaphragm type pumps but also include centrifugal trash and submersible non-clog styles.

WARNING: Do not use in explosive atmosphere or for pumping volatile flammable liquids. Do not throttle or restrict the discharge. Recommend short lengths of discharge hose since a diaphragm mud pump is a positive displacement type and they are not built with relief valves.

The difference in how hydraulic and electric motors generate power will determine how well each type of motor handles challenging conditions. Electric motors use magnets and copper wire windings to create electricity. These windings change resistance when covered in fine dust or moisture, and salt spray results in corrosion.

Hydraulic motors are powered by separate diesel engines which generate power by burning liquid fuel (gas or diesel) to compress hydraulic oil inside of a cylinder that powers the pump. Hydraulic oil is a fluid designed to resist compression with the result of moving pistons that can power practically anything. With no electricity being generated and no delicate windings involved, hydraulic power units work well in the dirtiest and most challenging environments. Hydraulic power units are also enclosed and operated at a distance from the actual pump, keeping them clean. They’re also the best choice for submerged installation since hydraulic units are more easily sealed than electric motors.

Challenges that develop during the slurry pumping process also pose a risk to the motor itself. When the load on the motor increases dramatically, both hydraulic and electric models will eventually stall. The hydraulic system will usually start back up again with no damage, while full stalling usually leads to severe damage in an electric motor. With slurry pumps capable of causing sudden load changes, it’s hard to prevent damage to an electric motor without oversizing it.

The policy set forth below outlines the personal data that Power Zone Equipment may collect, how Power Zone Equipment uses and safeguards that data, and with whom we may share it. This policy is intended to provide notice to individuals regarding personal data in an effort to be compliant with the data privacy laws and regulations of the jurisdictions in which Power Zone Equipment operates.

Power Zone Equipment encourages our employees, independent contractors, customers, suppliers, commercial visitors, business associates, and other interested parties to read this policy. By using our website or submitting personal data to Power Zone Equipment by any other means, you acknowledge that you understand and agree to be bound by this policy, and agree that Power Zone Equipment may collect, process, transfer, use and disclose your personal data as described in this policy.

Power Zone Equipment is committed to maintaining all reasonable precautions to ensure the privacy and security of personal data gathered by Power Zone Equipment. During your use of our website or through other communications with Power Zone Equipment, personal data may be collected and processed by Power Zone Equipment. In general, Power Zone Equipment collects personal contact information (e.g. name, company, address, telephone number and e-mail address), which you knowingly provide either by registration, requesting quotes, answering questions or otherwise for use in our commercial relationship. At times we may collect additional personal data that you voluntarily provide, including, but not limited to, job title, additional contact information, date of birth, hobbies, areas of interest, and professional affiliations.

Power Zone Equipment’s website is intended to be used by Power Zone Equipment customers, commercial visitors, business associates, and other interested parties for business purposes. Personal data collected by Power Zone Equipment through its website or by other means is used in support of our commercial relationship with you, including, but not limited to, the processing of customer orders, orders from vendors, managing accounts, learning about customers’ needs, responding to inquiries, and providing access to information. Also, in compliance with the laws and regulations of the relevant jurisdiction to support our relationship with you:

we may use third party service providers to assist us in collecting, assembling or processing personal data in connection with services related to our business relationship;

we (or a third party on our behalf) may use personal data to contact you about a Power Zone Equipment offer in support of your business needs or to conduct online surveys to understand better our customers’ needs; and

If you choose not to have your personal data used to support our customer relationship (especially direct marketing or market research), we will respect your choice. We do not sell your personal data to third parties, nor share it with third parties except as set forth in this policy. Power Zone Equipment will retain your personal data as long as you maintain a customer relationship with Power Zone Equipment and/or if you have registered to receive marketing or other communication from Power Zone Equipment, until such time as you request that we delete such personal data.

Power Zone Equipment is the commercial operator of its website and uses service providers to assist in hosting or otherwise acting as data processors, to provide software and content for our sites and to provide other services. Power Zone Equipment may disclose personal data supplied by you to these third parties who provide such services under contract to protect your personal data. In addition, where consistent with the laws and regulations of the relevant jurisdiction, Power Zone Equipment may disclose personal data if such disclosure:

For our customers in Switzerland and the European Union (EU), please note that Power Zone Equipment is a US based company. If you use our websites or web portals or, all information, including personal information, may be transferred to Power Zone Equipment (including subcontractors that may be maintaining and/or operating our website) in the United States and elsewhere and may be transferred to third parties that may be located anywhere in the world. Although this may include recipients of information located in countries where there may be a lower level of legal protection for your personal information than in your location country, we will protect your information in accordance with requirements applicable to your information and/or location. Specifically, for data transfers out of the EU, Power Zone Equipment will utilize data transfer agreements containing the Standard Contractual Clauses. By using our websites or web portals, you unambiguously consent to the transfer of your personal information and other information to the United States and elsewhere for the purposes and uses described herein.

When you access Power Zone Equipment’s websites or web portals, we may automatically (i.e., not by registration) collect non-personal data (e.g. type of Internet browser and operating system used, domain name of the website from which you came, number of visits, average time spent on the site, pages viewed). We may use this data and share it with our worldwide affiliates and related service providers to monitor the attractiveness of our websites and improve their performance or content. In this case, processing is performed on an anonymous basis and at Power Zone Equipment’s discretion.

In addition, certain online technical applications or other interactions you have with Power Zone Equipment may require the entry of business and technical data. By providing the requested information, you are consenting to the processing and storage of such information by Power Zone Equipment. Unless Power Zone Equipment is advised that you want this information removed from Power Zone Equipment’s server, such information may be retained by Power Zone Equipment and used for future commercial communications. A request for removal of this information can be made at the contact information provided below. Power Zone Equipment will take all reasonable precautions to assure that no such information will be provided or divulged to other third parties, except, if applicable, those third parties performing site hosting, maintenance, and related site service activities.

Cookies are information stored automatically on a website user’s computer. When a user views Power Zone Equipment’s website(s), Power Zone Equipment may store some data on the user’s computer in the form of a “cookie” to automatically recognize the user upon future visits to Power Zone Equipment’s website(s). Power Zone Equipment will make reasonable efforts to ensure compliance with the laws and regulations of relevant jurisdictions with regard to cookies.

Power Zone Equipment will not knowingly collect personal data from children under the age of 18. Power Zone Equipment’s website(s) is not intended for individuals under 18 years of age

Power Zone Equipment will take reasonable precautions to protect personal data in its possession secure against the risk of loss, misuse, unauthorized access, disclosure, alteration and destruction. Power Zone Equipment periodically reviews its security measures in an effort to ensure the privacy of personal data.

Power Zone Equipment will use personal data only in ways that are compatible with the purposes for which it was collected or subsequently authorized by you. While Power Zone Equipment will take reasonable steps to ensure that personal data is relevant to its intended use, accurate, complete, and current, Power Zone Equipment is also relying upon each individual to assist in providing accurate updates of his or her personal data.

Power Zone Equipment website(s) may contain “links” to websites owned and operated by third parties. By accessing these links, which are provided for your convenience, you will leave our site and will be subject to the privacy practices of the other website. This policy does not apply to any personal information you provide to unrelated third parties.

In general, Power Zone Equipment will only retain personal data for as long as needed for the specific purpose of processing and in accordance with Power Zone Equipment’s records management policy, or as otherwise required by the laws and regulations of a particular jurisdiction. For example, data will be retained during the time period that you are authorized to use Power Zone Equipment website(s), including any Power Zone Equipment tools accessible through our website(s). Upon termination of such authorization, your personal data related to use of Power Zone Equipment website(s) will be removed.

Upon request, Power Zone Equipment will grant individuals reasonable access to personal data that it holds about them. In addition, Power Zone Equipment will take reasonable steps to permit individuals to correct, amend, or delete information that is demonstrated to be inaccurate or incomplete. Power Zone Equipment also relies upon each individual to assist in providing accurate updates of his or her personal data. In order to access, correct, amend, or delete the personal data Power Zone Equipment holds about an individual, the individual should contact the following:

If your personal data is processed in the EU or you are a resident of the EU, the EU General data Protection Regulation grants you certain rights under the law. In particular, the right to access, correct, or delete the personal data Power Zone Equipment holds about you.

To the extent required by applicable law, Power Zone Equipment will grant individuals reasonable access to personal data that Power Zone Equipment holds about them and will take reasonable steps to permit such individuals to correct, amend, or delete information that Power Zone Equipment holds about them. Power Zone Equipment also relies upon each individual to assist in providing accurate updates of his or her personal data. In order to access, correct, amend, or delete the personal data Power Zone Equipment holds about an individual, the individual should contact his or her Power Zone Equipment commercial contact or contact us at the following email address:sales@powerzone.com.

If you have a comment, question, or complaint about how Power Zone Equipment is handling your personal data, we invite you to contact us in order to allow us to resolve the matter. In addition, individuals located in the EU may submit a complaint regarding the processing of their personal data to the EU data protection authorities (DPAs). The following link may assist you in finding the appropriate DPA:http://ec.europa.eu/justice/data-protection/bodies/authorities/index_en.htm.

Power Zone Equipment reserves the right to modify this policy from time to time in order that it accurately reflects the legal and regulatory environment and our data collection principles. When material changes are made to this policy, Power Zone Equipment will post the revised policy on our website.

If you have any questions or comments about this policy (e.g. to review and update, or remove your personal data from our database) please contact +1-719-754-1981 orsales@powerzone.com

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Rated at 7,500 psi, and with a 14” stroke, the PZ 2400 enables contractors to drill longer laterals with optimal flow and pressure. Combined with Redline consumables, customers can expect to see improved performance and decreased downtime, lowering customers" total cost of ownership.

The PZ 2400 features a Y-shaped module design, meaning less stress is placed on the pumps internal components and higher flow rates can be achieved with improved fatigue life.

Mud pump, refers to the drilling process to the drilling mud or water and other washing liquid machinery. The main components are volute, impeller, pump seat, pump case, support cylinder, motor seat, motor and other components. Impeller nut is cast iron, so corrosion resistance is good, and convenient processing technology. Pump seat is equipped with four skeleton oil seal and shaft sleeve, prevent shaft wear, prolong the service life of the shaft.

ATO offers high quality vertical mud pumps with thick, solid shaft and copper motor. Various models are available, such as 2 inch mud pump, 3 inch mud pump, 4 inch mud pump and 6 inch mud pump.

Vertical mud pump is used as suction and pouring of river mud, suitable for oil refining, construction, printing and dyeing, chemical industry and other industries.

Please send us your inquiry with detail item description or with Model number. If there is no packing demand we take it as our regular exported standard packing. We will offer you an order form for filling. We will recommend you the most suitable model according to information you offered.

We can give you really high quality products with competitive price. We have a better understanding in Chinese market, with us your money will be safe.

Having a quality mud pump is a critical part of keeping your oil well drilling system running as smoothly as possible. Dragon carries a wide range of mud pumps for systems of all kinds and jobs of all sizes. We also carry a 50 BPM mud mixing table to make drilling fluid mixing more efficient and accurate so you can always get the job done safely and correctly. View our full well service pump and mud pump selection to find the right system for your job site, or check out the rest of our drilling rigs for even more options.

We have attained huge reputation as prominent manufacturer and supplier of Portable Dewatering Submersible Pumps. These pumps are well accepted in the market for their light weight, robust construction and excellent functional accuracy. We design these pumps by utilizing latest tools and techniques as per latest industrial norms with quality tested raw materials. We supply these machines in wide specifications at affordable price range to our customers.

• Portable submersible pumps are one of its kinds. We have a wide range of selection within the same Horse Power rating for these pumps. Our construction is robust compared to other make pumps and has proved its self in the market with its trouble free Operation

• Impeller - We give non-clog impeller which will help Dewatering polluted liquid easily. Different MOC"s are provided to fight abrasive nature of the polluted liquid

• Motor – submersible pumps are available in Single phase and three-phase squirrel cage induction dry motor with ‘F" class insulation and IP 68 protection

• We provide pumps with Aluminum MOC, which will make the pump very light and will be extremely handy for the operator. Trolley mounted construction is also an available option

The global mud pumps market size is expected to grow at a CAGR of 3.80% during the forecast period of 2023-2028. The market growth is likely to be driven by the increasing frequency of exploration activities due to the rising demands for energy and reduction in harmful carbon emissions.

Mud pump is a type of piston/plunger driven pump that is capable of utilizing drilling fluids under high pressure. The mud pumps are an essential part of heavy drilling processes and are usually used in conjunction with other pumps. These pumps help circulate the drilling fluid through the drill bit and bring it back to the surface.

The increasing demand for minerals, oil, and gas has expanded the demand for mud pumps. With rising offshore mining activities and the rapidly thriving population around the world, the market is expected to expand further in the forecast period.

The mud pump market is expected to develop rapidly with the benefits provided by it. Increasing demand for directional and horizontal drilling and the mud pump’s capability to handle high-pressure drilling operations can further propel the market.

Technological advancements have enabled mud pumps to eliminate harmful carbon emissions and increase operating efficiency. With the increasing demand for electric mud pumps, the market can experience new growth opportunities.

Based on type, the market can be segmented into a duplex, triplex, and quintuplex. Based on operation, it can be bifurcated into electric and fuel engine. Based on application, the market can be divided into oil and gas, mining, and construction, among others. The regional markets for the mud pumps market can be divided into North America, Europe, the Asia Pacific, Latin America, the Middle East and Africa.

The comprehensive EMR report provides an in-depth assessment of the market based on Porter"s five forces model along with giving a SWOT analysis. The report gives a detailed analysis of the following key players in the global mud pumps market, covering their competitive landscape and the latest developments like mergers, acquisitions, investments and expansion plans.

Based on types, the mud pump market can be segmented into a duplex, triplex, and quintuplex. Among these types of pumps, triplex pumps are likely to account for the largest share of the market due to the advantages they provide over duplex pumps. The shift from duplex pumps to triplex pumps is expected to propel the market growth owing to its lesser weight and similar efficiency.

Based on operation, the mud pumps market can be bifurcated into electric and fuel engine. The electrically operating mud pump segment is rapidly developing due to its environmental advantages over the fuel engine pumps. With the increasing exploration activities conducted in all the regions around the world to meet the surging demand for energy and minerals is expected to amplify the market value.

Mud King Products, headquartered in Texas, United States, is a company operating in the oil and gas industry. The company was founded in 2000 and has been working in specialized sectors to manufacture various such as triplex mud pumps, handling tools, swivel cartridges, gate valves and butterfly valves, block hooks, and rotary tables.

GD Energy Products, LLC is an oil and gas company, founded in 1859, headquartered in Texas, United States. It is a global leader in the design and manufacturing of positive displacement pumps and associated aftermarket parts. The company provides products and services including falcon spring retainer, pump repair, redline packing, mud pumps, coiled tubing, and electric fracturing, among many other services.

Schlumberger Limited is a global technology company engaged in the field of oilfield services company. The company is founded in 1926 and is headquartered in Texas, United States. The company has been working in more than 120 countries with an aim to launch innovative and industry-changing technologies to promote energy efficiency.

*At Expert Market Research, we strive to always give you current and accurate information. The numbers depicted in the description are indicative and may differ from the actual numbers in the final EMR report.

JASON MUD PUMP (SIMILAR TO HALLIBURTON HT-400)(Ref#2947T)  15k fluid end, 750 QSX Cummins (built 2014) with 7750 hours, Allison 6061 (rebuilt 2014), hydraulic charge pumpca, manifold  Price:  $239,500

OPI 700 HDL TRIPLEX PUMP(Ref#7719T)  700 hp at 150 rpm, fully rebuilt, Cat 3408 engines (approx. 15000 hours and run very well)  Two available  Price:  $275,000 CDN each

NATIONAL 12P-160 TRIPLEX MUD PUMP(Ref#5586T) 3 available in India. 1600 HP, rated pump speed 140 strokes per minute, maximum fluid cylinder liner bore 6¾”, stroke 10", 10,000 PSI hydrostatic pressure of standard cylinder. 2.853 ratio of gears. 10" suction connection, 6" discharge connection. Valve pot mod .7., steel fluid ends, 5,000 psi pulsation dampener. Oilfield skid mounted. Performance Data: at 120 strokes per minute with 6¾” liners, pump will produce 4305 PSI and 574gpm. Set up for electric power. Dimensions and weight: 84,700lbs, 209"L x 113"W x 75"H. Built 1976. Located India, removed from offshore drilling rig.

NATIONAL 12P-160 TRIPLEX PUMPS(Ref#2355R)  3 available, driven by GE752 traction motor, 1600 hp, 12” stroke, 5000 psi, surge chamber, skid mounted, located Middle East  Price:  $310,000

NATIONAL 12P-160 TRIPLEX PUMPS(Ref#8938R)  3 available, overhauled by National Oilwell (ready in 2-3 weeks after purchase), 1600 hp @ 120 stroke per minute, 12” stroke, 5000 psi, skid mounted, GE Amerimex 752 traction motors, new liners, seats, valves and pistons  Price:  $295,000 each

NATIONAL 12P-160 MUD PUMP(Ref#2062Re)  Refurbished, complete with South West fluid ends and DC traction motors, located Middle East, 3 available  Price:  $720,000 each

NATIONAL 8P80 TRIPLEX MUD PUMP(Ref#9073R)  800 hp, 6-1/2” x 8-1/2”, FS, FS FE w/QC caps and cylinder head caps, Oteco 3” shear relief valve, suction screen, 5 x 6” centrifugal charging pump, powered by Cat 3412 diesel engine, rod cooling pump, Oteco type D pressure gauge, mud valves, bull wheel, master skidded, complete, good condition  Price:  $275,000

NATIONAL OILWELL 850 HP MUD PUMP(Ref#15442T)  Mattco API-9 fluid end rebuilt, very little use after rebuild, pulsation dampener, no engine, skid mounted  Price:$22,000

NATIONAL 7-P-50(Ref#6302R)  750 hp, 8” stroke, 6” suction inlet, 4” discharge outlet, piston size 4-1/2” – 7”,  max rod load 85,000#, approx. weight 11,500#, lubrication force fed, steel pump power end, double helical gears, 4.95:1 gear ratio, rod bearings sheel type replaceable, main bearings straight roler, pinion bearings spherical roller, crankshaft 1pc forged alloy steel, connecting rod knuckle joint, crosshead guide bronze replaceable, piston type fluid end Monoblock design, from high strength alloy steel, treated and sonic tested, Cat D379 diesel engine, 500 HP max linear bore size 3-1/2 – 6-1/4 x 7-3/4” stroke, test pressure 10,000 psi, gear ratio 2.742.8” suction line to 4 discharge stroke, location South America  Price:  $110,000

NATIONAL JWS 165 WELL SERVICE TRIPLEX PUMP WITH 140 BARREL WORK TANK(Ref#2633Tb) 5 x 6, Detroit 8V71 engine, standard transmission, skid mounted   Price:$87,500

NOV JWS 340 TRIPEX MUD PUMPS(Ref#2345T)  Two available, Skidded, Detroit Series 60 diesel engine DDEC V (475 hp), Allison 750 (6-speed) transmission with lock up control pane, Mission 4 x 5 centrifugal suction pump, 4” plungers, pulsation dampener, pressure gauge, safety valve, 10,000 psi fluid end, 5000 psi working pressure, NOV plug valve control manifold (4-valve) configured for 15k operation.  Can be configured to kill wells, acidize, cement, reverse circulate, drill out frac plugs or run in tandem.  Self-contained with fuel and fluid tanks and controls.  Steel canopy over skids, covered battery boxes, new batteries and disconnect switches.  Well maintained and in excellent condition.  Low hours on pumps and motors.  Ready to work.  Price:  $154,500 each

NATIONAL JWS300 MUD PUMP(Ref#2767R)  Series 60 Detroit diesel, 14 liter engine w/Allison transmission, mounted on oilfield skid, major overhaul, completely unitized with fuel tank, fluid end rebuilt by Matco  Price:  $195,000

NATIONAL OILWELL VARCO 308T-7(Ref#3358T)  4” Ceramic plungers, external drip lubricated, pulsation dampeners, John Deere 400hp engine, bypass oil filter, electric start, 200 gal fuel tank, well maintained, Hansen gear 7.25:1, Cobra with cooler   Price:$225,000

(2) NATIONAL C350 MUD PUMPS(Ref#3077N)  Standby – not pump in 15 years.  Pumped chalk continuously at 600 psi in a cement factory.  Complete with electrics and electric motor, complete, bull wheels and guards, complete, fluid end, pistons, liners, and valves.  Low hours.  Located Europe.   Price for both:  $105,000 loaded in a 40’ container

NATIONAL G700 14” STROKE DUPLEX MUD PUMP(Ref#8312Ta)  700 HP, 14” stroke, cast iron fluid end, surge chamber, 285 gpm @ 3550 psi with 5” pistons or 805 gpm @ 1265 psi with 8” pistons, mounted on skid 10’ x 23’ with enclosure, sold as is  Price:  $27,500

NATIONAL 5-1/2 X 10” MUD PUMP(Ref#14556Ta)  skid mounted with fuel tank, 471 Detroit diesel engine, 4 speed transmission, all new injectors  Price:  $16,500

NATIONAL C-100 DUPLEX MUD PUMP SYSTEM(Ref#10047R)  National C100 duplex mud pump (currently has 5-1/2” liners), gear end and mud end is in good shape, powered by 671 Detroit engine, 1000 gallon fuel tank capacity, tndem trailer mounted (air brakes), fully winterized enclosure with heater unit, locking doors and parts shelves, stairways and rails, 8” steel suction line/hose/sand screen pot/pole winch for adjustment of suction depth,   Price:  $50,000

IDEAL 5 X 10 DUPLEX MUD PUMP(Ref#9068T)453 Detroit engine (tall, not short), mounted on 5th wheel trailer, new bearings in crane case  Price:  $18,500

PERONI PTO/C TRIPLEX MUD PUMP(Ref#6306R)  110mm (4.331”) bore x 190mm (7.480”) stroke, 5000 psig, 125 rpm, 151.6 gpm, 350 psig, stainless steel flud end, Cummins Big Cam, Model NTC-350, built 1980, Eaton 23-speed manual transmission, Philadelphia Model 13HP-2 gear reducer rated 496 hp ratio 14:1, input 1760 rpm, output 126 rpm, pressurized lubricant system, fuel tank 300 gal, trailer mounted, 11’7”H x 41’4”L x 8’1”W double frame triple axle, king pin to 5th wheel, air brakes and lights, approx. 68,700#, located South America  Price:  $90,000

HHF 500 TRIPLEX MUD PUMP(Ref#2565Tb)   (Hongua International), year 2012, KTA 1150C (19-P750) engine, 6-3/4” cylinder diameter, 7-1/2” stroke, lots of spares  Price:  $150,000

NF-500 (CHINESE MANUFACTURED0 500 hp MUD PUMP(Ref#13723R)  Manufactured 2011, 550 gpm@3000 psi, Cat C15 diesel engine, pulsation dampener, mounted on Galvanized jack-up base, located Australia  Price:  $280,000

SKYTOP BREWSTER 7-1/4 X 14” MUD PUMP(Ref#13399Rb)  379 Cat didsel engine, Matco hi pressure forged steel fluid end, quick change valve heads, Hydril dampener, brand new expendables sill in box  Price:  $59,500

OILWELL 14PDH(ref#3813R)  7-1/4 x 14, Matco fluid end with screw type valve, covers and cylinder heads, Detroit 8V71 diesel engine, surge chamber, pip-off valve, 10 groove pully, 5-1/2” liners, mounted on oilfield skid, 1 year warranty on motor,  Price:  $90,000

OILWELL DUPLEX MUD PUMP(Ref#1190N)  Rebuilt with all new fluid end parts and rebuilt gear end, Detroit 8V71 diesel engine, mounted on oilfield skid, hand clutch, belt drive, belt guard, pulsation dampener, pressure gauge, pressure relief valve, cleaned and painted, factory specs:

OILWELL 4 X 6 MUD PUMP(Ref#8578T)  New belts, diesel power, new mud end parts, mounted on skid on 8’ x 16’ gooseneck trailer, ready to work  Price:  $28,000

EWS 440 UNITIZED MUD PUMP PACKAGE(Ref#599N)  refurbished Detroit Series 60 engine, refurbished Allison transmission, input horsepower rating 440 max, 320 max pump speed rating, 6” stroke length, 4-1/2” maximum piston size, 3000 psi fluid end working pressure rating, 3” (as required) discharge connection size, 6” (as required) suction connection size, 2” NPT accessory connection size, API#4 valve size, API#S-2 piston rod end, 35 gallon cancase oil capacity, 24 gallons liner wash capacity, internal gear ratio:  4.58:1, 6.517:1.  Price:  $200,000

DRAGON W-440 TRIPLEX 6” MUD PUMP(Ref#7756Ta)  skid mounted on 8’ x 28’ skid, Detroit 60 Series 8 cyl Turbo diesel power plant with 440 hp, on board fuel tank, M310 Series control panel  Price:  $132,500

L & L SMC T135-5 TRIPLEX 6” MUD PUMP(Ref#7756Tc)  mounted on 7’ x 21’ skid, Cat 6 cyl turbo diesel engine, in-line style system, hyd tanks  Price:  $29,500

MCFARLAND P38 PUMP(Ref#3917Ta)  low hours, 1”, 10,000 psi set up, pump can be configured for 18,000 or 25,000 psi, 60 hp electric motor, skidded  Price:  $27,500

FAMMCO TRIPLEX PUMP(Ref#2760T)  2 x SPM 600 HP 10K, 3-1/2 x 6’ stroke plunger, powered by (2) Cat C12 400 hp diesel engines, (2) Allison HT750 trans., (2) 4 x 5 cent pumps, (2) 5 x 6 slurry mixing pumps, 6 bbl mixing tub, 14 bbl averaging tub, mounted on 2002 tandem axle 8’6”W x 50’ step deck trailer  Price on Request

GARDNER DENVER PZ-11(Ref#10748R)  approx. 7000 hours, Cat 3512C (1476 hp), 5000 psi fluid end cylinder, 5-1/2” piston cylinder, antifreeze heaters, WPT W21-CG-300 Type 1 PTO clutch, 16 groove drive sheave, 16 groove bullwheel, 16 groove Kevlar belt with necessary guards, 5 x 6 x 11 charge pump c/w 50 hp@1200 rpm electric motor.  Discharge plumbing: 2” 5M XXH B/W Oteco gate valve, 4” 5M XXH b/w Oteco gate valve, 3” 5M Oteco popoff valve w/1502 connection, 2” 5M type D Oteco mud gauge with 1502 connection, Hydril 20 gal 5M pulsation damper.  Mounted on oilfield skid with separate, with expendables cabinet, knowledge box and removable engine skid for breaking the engine and pump into separate smaller loads.  Winterization package, oilfield lighting, explosion proof starters for charge pump, rod oiler pump and liner wash pumps.  Price:  $695,000 - Make Offer

GARDNER DENVER PZ9 TRIPLEX MUD PUMPS(Ref#7062T) Two Available, each complete with Cat 3508 diesel engines, pulsation dampener, and mud tanks with desander, desilter, etc.  Price for Package:  $110,000

GARDNER DENVER PZ9 TRIPLEX MUD PUMP(Ref#14850R)2 units available, no power, fully serviced to OEM specs in July 2008 and stored since then  Price for both:  $430,000

GARDNER DENVER PZ8(Ref#862T)  Rebuilt, complete, 8” stroke, 750 hp, alloy steel modular flud cylinders, 6-1/2” liners, liner wash system, API 7 valve pots, gear reducer, steel billet fluid end, pulsation dampener, suction connection, FF discharge connection, 4.5 gear ratio, skid mounted, 130”L x 88”W x 54”H POR

GARDNERDENVER PZ7(Ref#8588N)  US manufactured, freshly rebuilt, new Detroit Series 60 engine, Allison transmission, pulsation dampener, complete and ready to go.  Price:  $375,000

GARDNER DENVER PZ7 STYLE TRIPLEX MUD PUMP(Ref#1245Nb)  Reconditioned, inspected and tested.  550 hp input, Cat D379PCTA diesel engine (reconditioned), air start, muffler, standard instrument gauge panel, mounted on Cat rails, new 20CB500 air clutch, reconditioned radiator.  Belt drive assembly consisting of pump drive sheave, pump drive belts with belt guard, engine drive sheave, engine drive belts with belt guard, pillow block bearings.  Reconditioned Continental Emsco PD-45 12 gallon 5000 psi WP pulsation dampener.  New O’Drill/MCM ORV 21050 2” 1,000 – 5,000 psi WP shear relief valve.  New O’Drill/MCM 2” 0 – 6,000 psi WP type D mud pressure gauge.  PZ7 fluid modules complete with suction manifold and discharge strainer cross.  New CA-122 liner wash pump, pinion driven with spary nozzle system, water tank and hoses.  New fluid end expendables with 6” liners.  (3) runner oilfield type master skid with loading hitches.  New 5 x 6” R.H. centrifugal 178 series charge pump, 1-7/8 shaft, 10” impeller size, belt driven off pinion shaft, drive belts with belt guard.  New 6” fgure 400 hammer union.  New 4” 5000 psi WP gate valve, new 200 gallon air receiver tank, new air controls.  Price:  $455,000

Fitted with 5" Liner and pistons, bare pump, no extras, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED.

Fitted with 5” liners and pistons with washing and lubricating system, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with a rebuilt Detroit Diesel V1271 w/ Twin Turbo, 550 HP, with a chain case and a manual transmission

Fitted with liner & pistons, with rod washing & lubrication system, bare pump no extra"s, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with New CAT C13 (440 HP) diesel power unit, w/hand clutch, belt drive, belt guard, fuel tank.

Fitted with 5" Liner and pistons, w/washing & lubricating system, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with New CAT C15 (540 HP) diesel power unit, with manual transmission with 4 to 1 gear case, fuel tank.

GARDNER DENVER PAH(Ref#10664Rc)  rebuilt, Detroit 8V92 diesel engine, Allison 5960 transmission, new pistons, liners, valves, rebuilt engine   Price:  $210,000

Manufactured 2008, Cat C-9 new genset, 10 bbl tank, shaker, charging pump, Allison HT750 transmission, 1600 hours, mounted on mobile 52’ trailer  Price: $290,000

GARDNER DENVER PAH MUD PUMP(Ref#7546T)  8V92 Detroit diesel engine, Allison transmission, choke manifold on unit and charge pump, pistons and liners,  Price on Request

MUD KING PAH MUD PUMP(Ref#12669T)  Detroit Series 60 engine, Allison 750 transmission, 3” centrifugal pump, 90 bbl 2-compartment circulating tank  Price:  $290,000

GARDNER DENVER TRIPLEX MUD PUMP(Ref#8245Rb)  Completely rebuilt, new paint, skid mounted, new Detroit 671 engine 165 hp @ 1800 rpm, new fuel tank, lines and fluid end, multi speed transmission and clutch, 12 volt DC starting and operating system, 5” suction, 1742 to 10,000 psi discharge pressure, 8 – 138 gpm capacity, full functional control panel, mounted on oilfield skid, dims 240”L x 90”W x 60”H 12,000#  Price:  $39,500

KERR 2200 AND 3500 OR FMC M1214 TRIPLEX MIST PUMPS(Ref#7999T) Cat engines, 4 speed transmissions, rigged up with secondary containment, onboard lighting, winterization canvas for cold weather operations, Also available with Cummins or John Deere engines Priced from $77,500 to $97,500

GARDNER DENVER PQ172 TRIPLEX MIST PUMP(Ref#7827Ta)  Deutz F3L914 45hp 3 cyl air cooled diesel engine with electric start, manual transmission, gauges, 4’H x 4’W x 7.5’ long, 3” hardline, 22 bbl mixing tank, skid mounted  Price:  $17,500

GARDNER DENVER GXP TRIPLEX 6 X 16 MUD PUMP(Ref#11010T)  Skid mounted, twin Detroit 671 diesel engines, 30 ton, dimensions: 28’L x 11’W x 8’H   Price:  $32,500

GARDNER DENVER GXR 800 HP DUPLEX MUD PUMP(Ref#12423Rb)  Matco steel fluid end, pulsation dampener, fuel tank, gauges, controls, starter, mounted on oilfield skid, completely rebuilt engine and fluid end  Price:  $125,000

GARDNER DENVER FXN 7-1/4 X 14 MUD PUMP(Ref#1403T)  Cat 3408 engine air start with pump drive and belt guard, PD55 Hydril dampener, 750 gallon fuel tank, mounted on heavy duty drop deck tandem trailer,  low hours  Price:  $87,500

GARDNER DENVER FXN 7-1/2” X 14” DUPLEX MUD PUMP(Ref#8312Tb)  500 hp, on skid with Cat D343 engine, capable of 200 gpm @ 3000 psi with 4” pistons or 775 gpm @ 940 psi with 7-1/2” pistons, sold as is  Price:  $27,500

GARDNER DENVER FXN 7” X 14” DUPLEX MUD PUMP(Ref#6637Ta)Forged steel fluid end, quick change caps, Cat 3412 diesel engine, Hydril K20 3000 pulsation dampener, Demco 2” relief valve, belt drive, type F3000# pressure gauge, rod oiler pump, speed sensor, electric start, air clutch, skidded with roof, 3-1/2” x 20’L vibrating hose  Price:  $76,000

GARDNER DENVER FZ-FXZ MUD PUMP(Ref#4087Tb)  7-1/2 x 12, Tier 1 Detroit diesel 60 Series, 12.7L 500 hp, good gear and fluid ends, same-trailer mounted, 500 gal fuel capacity  Price:  $90,000

GARDNER DENVER FXZ 6-1/2” X 12” MUD PUMP(Ref#10287Tb)  Detroit 8V71 engine, hauled on 3 axle skid trailer with 1989 TTRAC International truck  Price:  $69,500

GARDNER DENVER FXN DUPLEX MUD PUMPS(Ref#8214R)  Two available, 14” stroke, 2” rod size, 400 hp, 75 strokes per minute, cast fluid ends, unitized on oilfield skid with Cat 3406 diesel engines, air start, new filters, oil and coolant, air receiver on deck, fluorescent lighting, drive belts with air clutch.  Gone over and in good operating condition, ready to be put into service.  Pumps currently have new 6” liners with production being 480 gpm @ 1000 psi.  All fluid end parts are brand new and never used, including the valves, gears, liners, pistons, rods, head gasket, and rod packing, equipped with pulsation dampener.  32’ long x 11’ wide x 7’ high 50,000# weight  Price:  $72,500 each

GARDNER DENVER FXZ 7-1/4 x 12”(Ref#8810R)  Trailer mounted, suction rod, suction strainer, twin GMC 150 hp engines, flywheel, belt guards, totally rebuilt 2011  Price:  $100,000

GARDNER DENVER FXZ 7 X 12 MUD PUMP(Ref#6602RD) only 1300 hours on new 12 Liter Volvo engine, air clutches, skid mounted, 20’L x 9’7”W x 8.4”H, 40,000#  Price:  $45,000

GARDNER DENVER 5-1/2 X 8 FXN DUPLEX MUD PUMP(Ref#6678T)  Cast fluid end, 671 Detroit, Spicer 6853-C transmission, hydraulic pump, air controls, 1” hyd hoses, skidded  Price:  $44,500

GARDNER DENVER 5 1/2 X 10 MUD PUMP(Ref#3261Rb)  6 cylinder Cummins diesel engine, hand clutch, 5 speed transmission, 5-1/2” liners, skid mounted, 10” stroke, ready to work  Price on Request

GARDNER DENVER 5 X 10 MUD PUMP(Ref#1480Tb)  air driven, used with cement for grouting wells, sitting 3-4 years, valves will need rebuilding, trailer mounted, air over hydraulic brakes, includes 28 joints of 21’ pipe  Price:  $39,500

GARDNER DENVER 5 X 10 MUD PUMP(Ref#5882Tb)  453 Detroit engine, battery start, mounted on oilfield skid with axles, starts and runs  Price:  $14,500

GARDNER DENVER FDFXDH MUD PUMP(Ref#14457T)  4” inlet, 3” outlet, pulsation dampern, new piston and rods, engine has been removed    Price:  $40,000

5-1/2 x 8” GARDNER DENVER MUD PUMP(Ref#4523N)  Manufactured 1960’s, rebuilt a couple years ago, skid mounted, 4 cylinder Detroit engine, used Supercharger, 637 hours on it, runs good, needs cosmetic work  Price:  $32,500

GARDNER DENVER 5 X 6 MUD PUMP(Ref#302Tb)  2 available, unmounted, rebuilt pumps, need normal expendables (neoprene is old in the valves etc)  Price:  $17,500

GARDNER DENVER FG-FXG 5 X 6 MUD PUMP(Ref#3510R)  Detroit diesel engine, mounted on tandem axle trailer, one suction and one discharge hose included  Price:  $39,500

GARDNER DENVER 5 X 6 MUD PUMP(Ref#13203T)  electric drive, in custom skid, fully rebuilt gear end and fluid end, excellent condition  Price:  $22,500

GARDNER DENVER FXF-DE8 4 X 5 MUD PUMP(Ref#10148T)  Manufactured 1996, new condition of gear and fluid ends, no engine, new 4” liners, new pistons, new chrome rods, new valves, new liner studs in head, new suction flange and gasket, new 2” steel discharge flange  Price:  $13,500

4 x 5 GARDNER DENVER PISTON MUD PUMP(Ref#7097Rb)  bull wheel or can be connected to hydraulic motor, 75% condition, needs some work  Price:  $5,500

GARDNER DENVER 5 X 6 HYDRAULICALLY DRIVEN MUD PUMP(Ref#2505T)  approx. 2500 hours, unmounted, (taken off a rig), fluid ends have not been rebuilt  POR

GARDNER DENVER PE5U 4X5 TRIPLEX MUD PUMP(Ref#11077c)  powered by Cat 3306 diesel engine, Eaton 5-speed transmission, manifold, enclosed building  Price:  $72,500

GARDNER DENVER PE5 TRIPLEX MUD PUMP(Ref#4692Ta)  Detroit 6V71 engine, electric start, radiator, 2” Shear relief valve, Spicer manual transmission, skidded  Price:  $25,000

GARDNER DENVER TEE PUMP(Ref#1654T)  Manufactured 1998, 1602 hours, 4" plungers with hydraulic charge pump, Detroit Series 50 (rebuilt), 5 speed, Skid mounted with fuel tank, Rebuilt expendables with seals, valves, seats, packings and gaskets.  Price:  $72,500

GARDNER DENVER TEE MUD PUMP(Ref#6440T)  New, unused, manufactured 2014, 4 available, bare pumps  Price:  $39,500 each  New Cat C7 engines available at additional cost

GARDNER DENVER TEE 4 X 5 TRIPLEX MUD PUMP  **NEW**(Ref#9115R)  4” piston and liners, well servicing valve and seats, bare pump, extras a extra cost, 2 available (1 plunger and 1 piston)  Price bare pump:  $64,000

(1) NATIONAL C250 DUPLEX MUD PUMP7-1/4 x 15”, New fluid end parts, bolt on valve cover, Rebuilt gear end, Pulsation dampener, new Cat C15 diesel or 12V71 diesel engine, Electric start, Controls, gauges, safety shut off, Master skid   Price with Cat engine:  $135,000   Price with Detroit engine:  $120,000

GARDNER DENVER FXK 7 1/4 x 14” DUPLEX MUD PUMP  New fluid end part, Rebuilt gear end, Detroit 12V71 diesel engine, Electric starter, Controls, gauges, Safety shut off   Price:$80,000

(2) NATIONAL C-150 DUPLEX MUD PUMP 6 ¾ x 12”  250 gpm / 550 PSI, New fluid end part, Rebuilt gear end, Pulsation dampener, Detroit diesel engine, Electric start, Controls, safety shut down, Master skid  Price:$80,000   6 weeks delivery

7” x 12” WHEATLEY DUPLEX MUD PUMP  (rebuilt), Model 27-12, powered by rebuilt 671 Detroit diesel engine, rebuilt gear end and fluid end, with all new fluid end parts, hand clutch, pulsation dampener, rod lubricating gland, pressure gauge, pressure relief valve, belt drive, belt guard, fuel tank, battery start, mounted on oilfield skid, cleaned and painted, guaranteed for 6 months, delivery 12 weeks after order  Price:  $42,000     Delivery 12 weeks

CENTERLINE 7-1/2 X 10 MUD PUMP(Ref#14556Tb)  high pressure, no engine, needs retaining liner cage and (1) side suction manifold needs replacing, unmounted  Price:  $39,500

CENTERLINE MODEL CLM 7-1/2” X 10 MSPA, 7-1/2 X 10 MUD PUMP(Ref#10877T)  Manufactured 2017, 150 GPM, 400 PSI, Centerline Mono, used for one job to go to 200’ to pump water, unmounted, no engine, like new condition  Price:  $26,500

WHEATLEY 5 X 10 MUD PUMP AND KING SWIVEL(Ref#1557Nm)  20 bbl tank, mounted on gooseneck double axle dual tires trailer, 1995 International single axle tractor, hoses, hydraulic valves and hoses  Price:  $95,000

CONTINENTAL EMSCO D500 DUPLEX MUD PUMP(Ref#5074Tb)  Trailer mounted, Detroit Series 60 diesel engine 14L, 40’ tandem axle trailer with hydraulic leveling jacks, currently working  Price:  $87,500

EMSCO D500 DUPLEX MUD PUMP(Ref#6329T)  16” stroke, 500 hp, ductile iron fluid end, Cat D353 diesel engine with radiator, 640 hp, 1300 rpm, inline 6 cylinder, 4 stroke, 6-1/4” bore x 8” stroke, (1473 in3) displacement, turbo charged (air to air aftercooled) aspiration, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons.  Price:  $37,500

EMSCO D500 DUPLEX MUD PUMP(Ref#6118Rh)  Emsco D500 duplex mud pump with steel fluid end, Hydril K-20-3000 pulsation dampener, belt driv with Cat D379 diesel engine, air starter, radiator, air clutch, mounted in 12’ x 29’L mud pump house with parts bin, controls  Price on Request

EMSCO D500 DUPLEX PUMPS(Ref#8722R)  Two available, Cat 3406C diesel engine, Cotta gear box, mounted in enclosed building 11’6” x 30’  Price:  $70,000

EMSCO D500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Tc)  500 hp, Mounted on skid with Cat D353 engine, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO D500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Td)  500 hp, Mounted on skid with twin Detroit engines, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO DA-500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Te)  500 hp, Mounted on skid with Cat D353 engine, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO D-300 6 X 14 DUPLEX MUD PUMP(Ref#3360Tb)  Excellent condition, skid mounted on tandem axle heavy duty lowboy trailer, fluid end rebuilt with new 6” liners, liner cages, piston rods, swabs, rod packing, oiler pump, new Mattco end plug, Detroit 8V71 engine (good condition)  Price:  $44,500

CONTINENTAL EMSCO D175 7 X 12” MUD PUMP(Ref#12068Nb)  powered by 8V71 Detroit engine, flued end and engine rebuilt, all new expendables, junk box, fuel tank, air compressor and air clutch, skidded.   Price:  $100,000

EMSCO D300 DUPLEX MUD PUMP(Ref#8210N)  7 1/2 x 14, Matco steel fluid end with screw off caps, Cat 3406 diesel powered, Air chamber, Spare fluid end parts, Air start, Fuel tank, On oilfield skid, Mounted in an 11’ wide metal building, Good condition   Price: $120,000

GASO5885-WS  QUINTUPLEX PRODUCTION PUMP(Ref#10309T)  Pump only.  5” stroke, 300 hp, steel billet fluid end, 2-3/4” ceramic plungers, Delrim disc valves, 838 packing, 6” RF suction connection, 3” RTJ discharge connection, 231 gpm max, 2020 psi, max 360 rpm  Price:  $82,500

GASO 3364 MUD PUMPS(Ref#9104T)  Two available, rebuilt, cast ductile iron fluid ends, used for oil service, bare pumps, no engines, unmounted, one is flanged for suction/discharge, one is threaded  Price:  $20,000 each

GASO 1860 4-1/2 X 6 MUD PUMP(Ref#14394T)  Fluid end completely rebuilt, powered by 3 cyl Deutz diesel engine, trailer mounted, hoses and misc parts  Price$19,500

GASO MODEL 1742 5 X 10 MUD PUMPS(Ref#3276Rb)  John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank w/lock cap, Dayton oiler pump systemand tank, 4” suction hose and winch boom, 4’ back up bumper guard, front and rear loading hitches, 44” bullwheel with power band belt, large belt guard, 8’ x 17’ base (mud boat)  Price:  $62,500

GASO 1742 MUD PUMP 2-1/2 to 5 X 10(Ref#2412Ta)  Cummins 150 hp reconditioned engine with snap-in clutch, 90 gal diesel tank with lock cap,  Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ back up drill pipe bumper guard, front and rear loading hitches, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard  Price:  $82,500

GASO MODEL 1654 MUD PUMP(Ref#6937T) 5 x 8, drive shaft included, new gears and bearings 2019, new pistons and piston sleeves 2021, new valve rubber inserts and valve cup gaskets 2022, very good condition  Price:  $18,500

GASO 1550 MUD PUMP 2-1/2 TO 5 X 10(Ref#2412Tb)  Detroit 671 engine with Snap-In clutch (Gen Set approx. 1500 hours),  replaced fluid end parts with 4” liners,  mounted on 8’ x 12’ trailer with adjustable pintle and DOT lighting, 75 gal diesel tank with lock cap, Dayton oiler pump system and tank, 4” suction hose and winch boom, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard, 2’ x 2’ x 5’ lockable HD toolbox, mouting beams and steel/bolts  Price:  $41,500

GASO 5 X 10 MUD PUMP 1742(Ref#4047Rc)  8’ x 17’ base (mud boat), John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank, Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ backup drill pipe bumper guard, front and rear loading hitches, 42” bull wheel with power band belt, belt guard    PRICE:  $73,500

GASO T4507 TRIPLEX MUD PUMP(Ref#999Nb)  Triplex single acting reciprocating plunger pump, 450 hp, reconditioned rental package, aluminum bronze fluid end with 5-1/2” plungers, 642 gpm@ 1095 psi, new AR valves (3/09), Cat 3406 engine,  260 rpm, max GPM 1039, Max PSI 1200, skid mounted, coolers, controls, gauges  Price:  $175,000

5x10 GASO MUD PUMP AND TANK SYSTEM(Ref#240N)  350 gpm @ 330# psi, skid mounted trailer w/6V71 Detroit diesel engine, shale shaker 4 X 5 Schrem, 1000 gallon tank, (2) desanders, hydraulic motor on mud pickup pump  Price:  $65,000

AMERICAN DUPLEX MUD PUMP  - NEW(Ref#14063N)  Model AXG (FG-AXG), capacity (with 5” liners) 200 gpm (757) x 310 psi (21 kgcm2), @ 100 rpm, bare pump, no engine  Price:  $25,000

UNION T68 TRIPLEX MUD PUMP(Ref#999Na)  Triplex single acting reciprocating plunger pump, 6” plungers, 405 hp, 4.95:1 gear ratio, powered by 8V92T Detroit diesel engine and transmission, 617 @ 1061 psi at 210 rpm, Max GPM 620, Max PSI 1060, skid mounted, cooler, controls, gauges  Price:  $130,000

1600 HP F1600 TRIPLEX MUD PUMP(Ref#1401N)  Made in China, electric motor, Model HHF1600, triplex single acting piston type, 7” x 12” max diameter of liner stroke, 120 spm, 1176kW (1600hp) rated power, gear ratio 4.206, 12” stroke of piston, pump valve API 7#, 7” max ID of liner, max working pressure 34.3 MPa (5000 psi), max displacement (130 s/min) 50.42L/s, diameter of discharge pipe 127mm (5”), diameter of suction pipe 304mm (12”), weight 25570kg (56,000 lbs).  combined v-belt transmission 800 kw (1072 hp) * 2, 25 (J)-5-7630 V-belt, transmission ratio 2.377, Model YZ08 motor 800kw, 60 hz, Model SB6”  8” J-12 1/2” charging pump, 8” diameter outlet, 6” diameter inlet, 200m3/h displacement, 55kW power of centrifugal motor  Price:  $425,000

BOMCO SJF-1600 MUD PUMP(Ref#9621R)  1600 hp, 12” stroke, 5000 psi, pulsation dampeners, pop off pressure release valve, pump pressure gauge, forged discharge manifold, overhead track for chain hoist, mounted on shipping skid, line washer pump, 6” liners, overall size:  192 x 128 x 105-3/4”, inspection report available, 4 available    PRICE:  $137,500 each

BOMCO F-1600 MUD PUMPS(Ref#6252T)  2 available, Built 2007, powered by 1500 hp GE traction motor  Model GEB29-A1, 5k fluid ends with pulsation dampener, liner washer pump and external oil pump, on a master skid with roof  Price:  $162,500 each

QINGZHOU ORF 1000 HP MZ-9 MUD PUMPS(Two Available)  (Ref#2798R)  Manufactured 2007 and 2008, 7” x 9” 1000 hp triplex mud pump, 5000 psi pulsation dampener, 5-star 5x6 centrifugal pump 50 hp electric motor, suction screen, centrifugal rod oiler, (2) 2005 Detroit diesel 560 14L 665 hp w/ zero hours, electric start, radiator, gauges, Wichita power grip clutch, all master skidded  Price:  $255,000

CONTINENTAL EMSCO MODEL FC2200 TRIPLEX MUD PUMP(Ref#2280T)  Complete without traction motors.  9” bore x 15” stroke, single acting, working pressure up to 7500 psi, (3) interchangeable forged steel fluid end modules with separate suction and discharge sections, Premium grade fluid end expendables with 6-1/2” pistons and liners, suction manifold with (3) 12” flanged inlets, SD8 suction desurger, pressure manifold with (2) 5-1/8” 10,000# API flanged outlets, liner wash system, 1 x 1-1/2” mission centrifugal pump p/b 3 hp electric motor, external power end lubrication pump, steel skid, suction line pressure relief valve, set of standard service tools  Price:  $675,000

EMSCO STYLE F1000 TRIPLEX PUMPS(Ref#9886T)  2 available, 6-3/4” liners with 644 gpm @ 2380 psi, belt driven charging pump, pulsation dampener, with 398 Cat engines, skid mounted, ready to work  Price:  $112,500 each

1200rpm) through WPT power grip 321. The unit is complete with a bull wheel, a set of V-belts, belt guard, a drive assembly and screw devices for tightening belts.

-The unitization includes an electric motor powered supercharging pump piped to the suction of the mud pump, an electric powered liner wash pump mounted and piped, engine and WPT power grip 321 controls at area of engine arrangement, industrial coating on all parts and labor to clean & make ready for shipment.

-Pump suction manifold is 12”, and intake flange diameter is 12”. A 12” valve is used in suction manifold. And two suction solutions are alternative, pump charging and self-suction.

-F-1000 mud pump is driven by diesel engine (Caterpillar 3512DITA, 1250 HP @ 1200rpm) through WPT power grip 321. The unit is complete with a bull wheel, a set of V-belts, belt guard, a drive assembly and screw devices for tightening belts.

-The unitization includes an electric motor powered supercharging pump piped to the suction of the mud pump, an electric powered liner wash pump mounted and piped, engine and WPT power grip 321 controls at area of engine arrangement, industrial coating on all parts and labor to clean & make ready for shipment.

-Pump suction manifold is 12”, and intake flange diameter is 12”. A 12” valve is used in suction manifold. And two suction solutions are alternative, pump charging and self-suction.

EWCOWH-600 TRIPLEX MUD PUMP(Ref#1183N)  Manufactured 1984, good condition, powered by (2) Cat 3408 engines, mounted on oilfield skid, located Southeast Asia, immediately available  Price:  $190,000

NEW CONTINENTAL EMSCO STYLE F-1000 TRIPLEX MUD PUMP(Ref#1287N)  triplex single action piston, max. liner size x stroke 170 x 254mm (6-34” x 10”), 140 r/min strokes rating, 753kW (1000 hp), Herringbone gear, 4.207:1 gear ratio, pressure and splash lubrication, 12” flange suction inlet, 5-1/8” flanger 5000 psi discharge outlet, 7-3/4” pinion shaft dia., 2” x 2” key, valve-over-valve API#6, approx weight 41,420 lb, fully interchangeable with Continental Emsco parts, complete with pulsation dampener, suction discharge, pressure gauge, complete fluid end expendables, guaranteed for one year, delivered to Houston from China factory,  2 available  Price, delivered to Houston:  $185,000 each      (30% deposit with order, balance due when shipped from China)

CONTINENTAL EMSCO F-800 TRIPLEX MUD PUMP(Ref#664T) 800 hp, 6-3/4”, forged steel fluid end, 50003 pulsation dampener, 3” Shear relief valve, skidded  Price:  $37,500

OFM600 TRIPLEX MUD PUMP(Ref#2497T)  Manufactured 2018, 1800 hours, very excellent condition, Detroit 60 Series engine, Allison transmission, 800 psi, dims/weight 20’ x 10’ x 8’, 20,000 lbs  Price:  $320,000

AXON HD-500 TRIPLEX PLUNGER PUMP(Ref#975T)  14 liter Detroit Diesel, 6061 Allison automatic transmission, rebuilt power end, new expendables in fluid end, new charge pump, skid, tanks, Pilfer 5 valve manifold, 15k fluid end, new paint  Price:  $215,000

WHELAND DUPLEX MUD PUMP(Ref#7936)  7-1/2 x 14”, Hydril K-20 pulsation dampener, Cat D342 diesel engine, 300 bbl 3-compartment steel mud pit with (2) 7.4 hp electric mixer motors  Price:  $55,000

FMC BEAN PUMP MODEL L1122DI(Ref#3916T)  122 hp, 91 kw, 1750 max rpm, 127 gpm, 519 lpm, 1300 psi, 9063 kpa, Baldor ECP4409T 100 hp motor, 1200 rpm synchronous speed, 60hz frequency, 460V (3P)  Price on Request

HYDRAULIC PUMP WITH KUBOTA ENGINE(Ref#5073T)  Lofa Industries hydraulic pump (6.2 hours) with Kubota V3800T engine, Hydac ELD cooling system  Price:  $24,500

Bean 35 mud pumps(Ref#7739R) completely rebuilt, skid mounted with Deutz diesel engine, 4 speed transmission, low 50 hours, stored inside   Price:$14,000

OILWELL C338H TRIPLEX WATER INJECTION PUMP(Ref#6530T)  3” plungers, 3540 psi max pressure, 336 hp @ 200 rpm input, Cat G3408 gas engine, Falk gear/transmission, 100 rpm input, 290 rpm output, ratio 3.793:1, service factor 1.98, 375 hp Price on Request

SPRAGUE SYSTEM 0-55 GPM, 3500 PSI DUAL SYSTEM PORTABLE TURBO DIESEL HYDRAULICPUMP  (Ref#9235R)  New Unit.  High pressure, low volume, self-contrained.  Capable of 5000 psi intermittent duty, designed for low maintenance and flow operation.  A single adjustable back pressure regulating circuit allows operator to adjust aircraft reservoir return condition and maintains a positive reservoir head pressure on the aircraft without fluid loss.  This feature allows the system to be used on drilling rigs with different reservoir pressure requirements.  Lighted control panel.  Automatic over temperature shut down, Reservoir high/low level automatic shutdown, Safety circuit boost pump pressure switch, loss of boost pump pressure automatically shuts system down, Phase reverse relay (does not allow pump to turn in wrong rotation), Automatic air removal device (this removes the air from the oil returning from the rig at flows up to 55 gpm automatically; results are no cavitation, longer pump life, quiet system.  Reservoir drain valve, Parking brake instrument panel lights 100 hp drive motor (Deutz 125 hp), International Reservoir and system fluid emperature indicator.  Chassis has a 2-wheel mechanical parking brake.  The lower portion of the chassis serves as f ull sized drain pan with drain valve.  Cabinet is skydrol resistant stainless steel.  Removable cover assembly for major maintenance with access doors for inspection and minor maintenance.   Price:  $185,000

TEST PUMP RIG(Ref#3417T)  Mounted on 12K GVRW trailer, hydraulic powered spool with approximately 500 of 2” hose, internally routed power and safety cable, 7.5 HP pump and motor, Whisper Watt 25kva 3-phase diesel generator with approx. 3100 hours  Price:  $45,000

HYDROPLEX 15K TEST PUMP(Ref#2496R)  Manufactured 2012, 15 gallons per minute, mounted on 2008 GMC C6500 truck with diesel engine, control box, manifold, 550 gal heavy duty Snyder Megatainer tank, 123,896 miles on truck  Price:  $85,000

SCHAEFER & URBACH BT 80-120 GERMAN MANUFACTURED TRIPLEX MUD PUMPS, POWERED BY AC MOTOR AND GEAR DRIVEN(Ref#6853N) 3 available “LIKE NEW”– Manufactured 2006, Speed Max/Count: 135 SPM, 220 bar – 350 bar (5000 psi), Max. Displacement 4,005 l/min at 150 bar, Max. pressure 1,565 l/min at 350 bar, Elin 6 AC Motor, 690V/75 Hz, 1000 KW, Mounted on skid 8100 mm long x 3000mm wide x 2960 mm high. 45,000kg, Sound level: 63dB(A)@ 7 meters, Operating hours: (1) 1668, (2) 1010, (3) 2069, NOV Mission Magnum 8 x 6 x 14 charge pump, Amtec 36 kw AC Motor, 400/690V/50Hz, NOV Mission Magnum 3 x 2 x 13 liner cooler pump, 2,2 kW AC Motor 400/690V/ 50 Hz, Hydrill K20 pulsation dampener, Zollern gear / mud pump, Located in Europe

MUD PUPPY MP-255(Ref#1065T) Mounted in 16" trailer with 3 stabilizing jacks, sand guzzler, 3 x 2 centrifugal pump needs replacing, 3100 hours, includes 4" hose for pick up pump