wheatley mud pump parts for sale

Wheatley Pump.com - Services all Duplex, Triplex and Quintuplex Plunger and Piston Pumps by Wheatley Pump and Frank Wheatley Inc. (FWI). We are your "one stop" source for all Wheatley pump needs - parts and service. We have all of the power end and fluid end parts for all Wheatley reciprocating plunger and piston pumps, both current and obsolete. We specialize in Wheatley Pumps; new, used and reconditioned pumps and remanufactured.

We hope that this web-site is helpful to you in keeping your Wheatley pump in good working order by giving you the technical tools you need to have. A list of parts and services is provided below for your convenience.

Adjust or replace these bearings at first sign of wear. The bearings in the crank end are babbitt lined steel shells, adjustable for wear by removing shims and easily replaced when completely worn. These bearings should be watched closely and adjusted at first signs of looseness.. You will note on series 3400, 3800, 3500, and 3900 pumps, that the shims do not completely fill the outer gap between rod and cap casting, although the connecting rod bolts are tight. This is because the faces of the shell bearings project slightly beyond the faces of the rod and cap castings, and the shims are gripped only between the faces of the bearing halves. Do not try to close this outer gap by tightening the connecting rod bolt as it will put an excessive strain on the bolts.

To check for wear, place a wrench on the top connecting rod bolt and shake the rod parallel to the crankshaft. (The pressure must be relieved from the liquid end of the pump, so that the pump"s mechanism is free to move.) If the rod bearing moves without resistance, the bearing may be too loose and need adjusting. If the bearing does need adjusting, remove shims until you cannot shake the rod, then add .005" shims one at a time until there is little side movement. Be sure to torque rod bolt nuts to proper value for each adjustment. Oil clearance should be checked with Plastigage (available in most parts stores). Wipe crankshaft journal clean of any oil, place a strip of Plastigage on the crankshaft journal and tighten rod cap to the proper torque value. Once tightened, remove rod cap and measure oil clearance with scale on Plastigage package. See oil clearance chart. (NOTE: If you are making this adjustment after having had the crossheads out, be sure that the oil holes in the rod are pointing up. The "up" side is indicated by matching numbers stamped on the cap and rod at the split between them. These numbers should be the same on each rod and should be on the top side of the crankshaft.) Rotate the shaft by hand and if there is any hard drag or tight spots in the bearing, add another 0.005" shim. After this bearing is properly adjusted, loosen bolts a few turns and repeat the above operation on the other bearings. After all bearings have been adjusted.

Torque all connecting rod bolt nuts back to proper value. Again rotate the pump by hand to check for excessive drag and tight spots. If none, the pump should be ready for operation.

If the pump cannot be rotated by hand due to the drive being enclosed, care must-be taken: not to over-tighten the bearings, since they cannot be checked by rotating the pump. When bearings are adjusted by this method, watch carefully for overheating when the pump is put into operation.

It is usually better to have a bearing a little too loose than too tight. A slightly loose bearing will cause very little trouble because of the slow operating speeds of the pump, but a tight bearing will overheat and the babbitt may melt or pull. Normal precautions must be taken to insure cleanliness of parts upon their assembly.

To check for wear, place a wrench on the top connecting rod bolt and shake the rod parallel to the crankshaft. (The pressure must be relieved from the liquid end of the pump so that the pump"s mechanism is free to move.) If the rod bearing moves without resistance, the bearing may be too loose and need adjusting. If the bearing does need adjusting, remove shims until you cannot shake the rod, then add .005" shims one at a time until there is a little side movement. Be sure to torque rod bolt nuts to proper value for each adjustment. (NOTE: If you are making this adjustment after having had the crossheads out, be sure that the oil holes in the rod are pointing up. The "up" side is indicated by matching numbers stamped on the cap and rod at the split between them. These numbers should be the same on each rod and should be on the top side of the crankshaft.) Turn the shaft by hand and if there is any hard drag or tight spots in the bearing, add another .005"" shim. After this bearing is properly adjusted, loosen bolts a few turns and repeat the above operation on the other bearings. After all bearings have been adjusted, torque all connecting rod bolt nuts back to proper amount. Again turn the pump by hand to check for excessive drag and tight spots. If none, the pump should then be ready for operation.

If the pump cannot be rotated by hand due to the drive being enclosed, the bearings may be completely adjusted by shaking the bearing on the shaft as stated above. Care must be taken not to over-tighten the bearings since they cannot be checked by rotating the pump by hand. When bearings are adjusted by this method, they must be watched carefully for overheating when the pump is put into operation.

Alternatively, plastic gauge strips, found in most parts stores may be used to adjust these bearings. It is usually better to have a bearing a little too loose than too tight. A slightly loose bearing will cause very little trouble because of the slow operating speeds of the pump, but a tight bearing will overheat and the babbitt may melt or pull. with experience, an operator can tell by feel when the bearings are properly adjusted. Normal precautions must be taken to insure cleanliness of parts upon their assembly. All wrenches used in adjusting these bearings are standard wrenches.

Wheatley engineering is supported by exact manufacturing processes. It is this commitment to quality that has made Wheatley plunger and piston pumps the most sought-after solutions for flow control problems. When you need a highly efficient reciprocating pump from 6 to 1800 horsepower, Our team delivers. Day after day… year after year.

Are you trying to navigate your way through the hundreds of different Wheatley pump parts on the market? Thanks to the variety of current and discontinued items, it can difficult to pinpoint exactly which parts you need to repair your pump. Don"t worry, IEQ Industries can help. Our online company offers parts and services for new, remanufactured and used Wheatley pumps. We also stock parts and pieces for Wheatley pumps that have been discontinued. Whatever it is you need, IEQ Industries is your number-one resource.

If you"re not sure which parts your Wheatley pump requires, our friendly customer service representatives will be happy to assist you. We work with customers all over the world, walking them through the process of reviewing their pumps to ensure the correct replacement parts are ordered. We understand that replacing a non-working pump is never ideal. Replacing a few of its parts is usually all it takes.

Should you already know which Wheatley pump parts you need, navigating our website to order plungers, valves or connecting rods is a cinch. If you want a price quote, simply head over to the "Get a Quote" option. Fill out the contact form to get more information or simply contact our customer service department at 1.800.544.9053.

At IEQ Industries, we"re not happy until you"re happy. More accurately put, we"re not happy until you have the parts you need to get your used or discontinued pump back into working order. Work with the company that cares--work with WheatleyPump.com.

*Note: "Danco Pump & Supply Co. is not a licensee or in any way affiliated with National Oilwell L.P. or it"s parent Company National Oilwell, Inc. and that neither National Oilwell L.P. or it"s parent company National Oilwell Inc. endorses any of the products or services offered by Danco. "National Oilwell", "Gaso", "Wheatley", and "Emsco" are trademarks belonging to National-Oilwell L.P."

"Danco Pump & Supply Co. is not a licensee or in any way affiliated with Gardner-Denver® and Gardner-Denver® does not endorse any of the products or services offered by Danco. "Gardner-Denver®" and all of its pumps and parts are registered to Gardner-Denver®."

We will help you find the pump that will work best for your specific needs, and we have the parts to service your existing pumps and even discontinued pumps. We offer full service on Wheatley Simplex, Duplex, Triplex, and Quintuplex pumps. So, we’re not just here to help you find the right pump, we’re also here to assist you in keeping your current and new pumps up and running.

We have years of experience in servicing and remanufacturing GASO and Wheatley pumps, and we know how to find the correct pump for whatever your application is. With our helpful team and large inventory of GASO and Wheatley pump parts we can offer quick solutions for all your pump needs.

Power Zone is a leading global supplier of new, used and reconditioned pumps for sale. Our inventory of pumps includes multi-stage centrifugal pumps, positive displacement pumps, reciprocating pumps, single stage centrifugal pumps and screw pumps in a variety of design standards including API 610 Centrifugal Pumps, API 674 Reciprocating Pumps and API 676 Rotary Pumps. We have an assortment of pumps that are used in various applications including water treatment, pipelines, frac water supply, salt water disposal and flood control in industries like municipal, manufacturing, oil & gas, mining and agriculture. We supply pumps of all major suppliers such as Sulzer, Flowserve, ITT Goulds, Aurora and National.

Pump Parts - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Pumps - Misc. - New 1 5/8" ceramic plunger for pump models: P-323, 59T-3, (T-365, T-385), 5P-323, & HP-125M ( 103Q-3, 110Q-3, Q3115) Price listed is for 1. More Info

Pumps - Misc. - 1 5/8" 838 plunger packing for Wheatley/National models: 110Q-3M, HP-125M, P-50A, P-100A, P-175, P-200, P-200A, P-300, 5P-300A, 5Q-300A, P-323, 5P-323, P-200B, 5P-200A, T... More Info

Pump Parts - Wheatley 5P-200A Quintuplex Injection Pump, Pumps & Parts, Used Wheatley 5P-200A Quintuplex Injection Pump, 1.75" metal plungers x 2.25" stroke, steel fluid end, on skid ... More Info

Pump Parts - Wheatley 5P-200A Quintuplex Injection Pump, Pumps & Parts, Used Wheatley 5P-200A quintuplex pump, 1.75" metal plungers x 2.25" stroke, steel fluid end, on skid with belt ... More Info

Pump Parts - Wheatley 5P-200A Quintuplex Injection Pump, Pumps & Parts, Used Wheatley 5P-200A Quintuplex Injection Pump, steel fluid end, 1.75" metal plungers x 2.25" stroke, disc val... More Info

Quintuplex Pumps - Used Wheatly 5p-323 quintuplex, aluminum bronze head, 2.5"" steel plungers, power end in excellent condition, mounted on skid, bull wheel and 40 hp electric motor. More Info

Pump Parts - Wheatley HP-160M Triplex Pump, Pumps & Parts, Used Wheatley HP-160M Triplex Pump, 3" Metal Plungers x 6 1/8" Stroke, 400 RPM, Steel Block Fluid End, Bolt on Suction Manif... More Info

Quintuplex Pumps - Used Wheatley HP-375L quintuplex plunger pump, steel billet fluid end, with 4" plungers, 500 gpm max, 995 psi max, 300 rpm max. More Info

Quintuplex Pumps - Used Wheatley HP-600M Quintuplex pump only. 7 1/8" Stroke, 600 HP, Forged Carbon Steel Fluid End, 2 5/8" Plungers, 300 gpm max, 3085 psi max, 360 rpm max. More Info

Pump Parts - Wheatley P-200 Triplex Plunger Pump, Pumps & Parts, Used Wheatley P-200 Triplex Pump, 0.75" metal plungers x 2.125" stroke, stainless steel high pressure block fluid end,... More Info

Pump Parts - Wheatley P-530A Triplex Plunger Pump, Pumps & Parts, Used Wheatley P530A Triplex Plunger Pump, steel fluid end, size 1.75-2.75" x 5.125" stroke, max HP 130, max RPM 360, ... More Info

Pump Parts - Wheatley Q-4240AM Quintuplex Saltwater Disposal / Injection Pump, Pumps & Parts, Used aluminum bronze fluid end for Wheatley Q4240AM Quintuplex Saltwater Disposal/Injecti... More Info

We stock fluid end parts for the5×6 mud pump, 5×6-1/4 FM45 mud pump, 5×8 mud pump, 5-1/2×8 mud pump, 5X10 mud pump, 4-1/2×5 mud pump, 7-1/2×8 mud pump, and 7-1/2X10 mud pump.  The Gardner Denver mud pump model numbers for the above pumps are as follows: 5X6-FGFXG, 5X8-FDFXX, 5-1/2X8-FDFXX, 5X10-FDFXD, 4-1/2X5-FFFXF, 7-1/2X8-FYFXX, 7-1/2X10-FYFXD.  We also handle Wheatley, Gaso, Worthington, Failing and Centerline parts and pumps. We also stock Foot Valve, Liner Puller, Valve Seat Puller, (4″ Inline Check Valve.  Our Gardner Denver mud pump parts are not only competitively priced, they are also made in the USA.  Oil Recommended by Gardner Denver.  Call any of our experienced representatives to get the help and knowledge you deserve.

We provide oilfield spares and spare parts for many major U.S. manufacturers and equipment, including: Airesearch, Elliott, Emerson Process, Continental Emsco Mud Pumps, Gardner Denver Triplex Pumps, Gaso Mud Pumps , Garrett, Harrisburg , Centrifugal Pump, Honeywell, Mission Centrifugal mud pumps, Mud Pump Expendables, National Mud Pump , NOV, Pratt & Whitney, Trico, Rosemount Analytical, Union Pump, Varco, Veritrak, Web Wilson, Wilson Snyder, Wheatley Mud Pumps, and Westinghouse Transmitters and obsolete and hard to source items.

From annular blowout preventer’s parts to RAM BOPs, from mud pump parts to Drawworks spares our goal is to provide our customers with the best quality and value in aftermarket, OEM, and reverse engineered replacement parts for such commodities as oil field equipment, refineries, and pipelines.

Titan Oil Tools  understands our customer"s critical need for high-quality USA made oil tools and parts, delivered on time, when and where you need them. Titan Oil Tools will provide the highest quality oil tools and oilfield parts and  equipment made in the USA.   We offer a complete line of oilfield supplies; equivalent repair parts and used equipment for Garret, Mission, Elliott, Varco, Airesearch, Continental, Guiberson type replacement parts  and more.

Mud Pump Spares; Mud Pump Consumables - "L" Modules - We sell high quality mud pumps spares, mud pump parts, and mud pump expendables including; mud pump liners and mud pumps pistons. They are competitively priced and have an outstanding service life. Manufactures include; Brewster, Continental Emsco, Ellis Williams, Gaso, Gardner Denver, IDECO, National, Oilwell, OPI, Wheatley, and Wilson.

Mission type mud pump liners. We are one of the few companies worldwide specializing in; and stocking “Mission” type high temperature mud pump liners. Our "Mission" type liners are formulated with two rare metals not found in common everyday liners. All of our "Mission" type mud pump liners include the seal ring and are individually packed for immediate export, offshore or domestic oilfield use. Manufactured to OEM specifications, our Mission type Discharge Module and Mission type Suction Module come complete with studs and nuts installed.

Titan Oil Tools is major supplier of expendables for mud pumps. We stock pistons, seats, valves for popular brand duplex mud pump parts and triplex mud pump parts. Call us for all your mud pump expendables.

We supply Wheatley mud pump parts, Ideco mud pump parts, Emsco mud pump spares and Gardner Denver mud pump parts and many more manufacturers. Call us for quality and the best prices.

We supply quality swabbing equipment which may include the swabbing assembly, shut-off valve on the well, also called a swabbing valve and also the lubricator. Parts may include Guiberson style oil tools replacement parts under the Titan name. Titan brand has equal specifications to Guiberson oil tools and is made in the USA. We can provide replacements for Guiberson Rope Sockets, Guiberson Hydraulic Oil Savers, Guiberson Safety Tools, Guiberson Sinker Bars, and Guiberson Tubular Jars.

Blowout preventer parts, Blowout preventer spares and blowout preventer replacement parts made in the USA. Our BOP parts , BOP spares, feature outstanding quality. We have Cameron BOP parts, Hydril BOP parts and Shaffer BOP parts.

Downhole tools for high-performance torque reduction and hole enlargement. These tools also will provide a major resistance reduction. Call us for genuine GE drilling motors, motor optimizers, mud motors, shock subs, drilling jars, downhole tool data loggers and more.

Elliott steam turbine parts have a reputation as one of the most reliable and versatile  in the industry. Elliott steam turbine parts have rugged designs and are built to perform for years of reliable service. Steam turbines have extreme value and work well in a broad range of mechanical and power generation applications, around the world 24X 7 365 days per week.

OIlfield supply parts include: Hydraulic gate valves, hydraulic check valves, blowout preventer parts, BOP parts, mud pump parts, mud pump spares, drawworks parts, drawworks tubing drum, drawworks bearings, drawworks seals.

Need Shaffer BOP parts or USA equivalents, then call Titan Oil Tools. If we do not have what you need in stock we will get it for your Shaffer LWS BOP parts quickly. Buy seal kits, sealing parts, rings, pistons and more for Shaffer LWS BOP.

Cameron BOP parts or USA equivalents are field-replaceable and the system may be field removed change-out without removing the BOP from the stack. Call for parts needed for the BOP Stack, Choke Manifold, BOP Control Systems, and Pressure Gauges.

We sell only the best quality, high durability valve parts for Cameron Valves. All of our Cameron  valve parts are made in the USA. Our valve spares offer exceptional quality and peformance.

Hydril invented the first hydraulically operated BOP in about 1933 and has been making innovations since that time call us for Hydril Blowout preventer parts and Hydril BOP parts.Call us for Hydril Annular BOP parts or USA equivalents, Hydril Type Ram BOP parts or USA equivalents.

Titan Oil Tools can provide AiResearch gas turbine parts and AiResearch gas turbine industrial turbochargers. Make your gas turbine the most efficient combustion turbine with our AiResearch turbochargers and gas turbine parts. AiResearch Gas turbine turbocharger parts achieve a higher degree of efficiency than other types of gas turbines.

We are your source to get Garrett turbine parts and Garrett gas turbine parts. We specialize in industrial Garrett turbine components that will improve the operating quality of your operations. Call if you need help for your Garrett turbine.

Used Wheatley HP-160M Triplex Pump, 3" Metal Plungers x 6 1/8" Stroke, 400 RPM, Steel Block Fluid End, Bolt on Suction Manifold, 4" Suction, 3" Discharge. Turns good.