npst pup joint pricelist

BLAZE is adequately equipped to supply NPST Pup joints made of high quality seamless pipeline with  male & female detachable hammer union. NPST has uniform bore for greater flow capacity. NPST pup joints are available in 2″ to 4″ sizes, length for pup joint range from 1 feet to 20 feet at 15000 psi. Pup joint with Non- pressure seal thread union (NPST) are especially engineered for high pressure, abrasive services where welded connections are not desired. The design provides a strong, permanent end connection without butt welding. An epoxy thread-locking compound secures the connection.

Casing or Tubing Pup Joints, Casing or Tubing Connectors and Casing or Tubing Couplings. In addition it is capable of Threading items at Groups 1, 2, 3 & 4 of API spec. 5CT. Items supplied by BLAZE meet the Quality Standards as defined in API 5CT assuring

BLAZE is also well equipped to supply Line Pipe Couplings/ NPST pup joints with wide range of specifications. In addition we can supply thread Line Pipes and its accessories of various sizes. Items meet the quality standards as laid down in API – 5L.

ADFO manufactures Pup Joints with Integral Hammer Union end connections.These Pup Joints are used on high pressure discharge lines, choke and kill lines, auxiliary flow and other applications.

Shreeraj Industries offers NPST (Non-pressure Seal Thread) Pups in size 1-3 Fig 602 and 1502. The NPST connection offers a light weight pup capable of 6000-15000 CWP with a connection that isolates the thread from fluid’s flowpath. This connection is permanent and is well suited to abrasive applications where a weldedread more...

Windlass manufactures Pup Joints with integral hammer lug union end connections. This enables faster, easier make-up and break-out of temporary flow lines.

TSI Flow Products provides a wide range of Flowline and Pup Joints to the oil and gas industry. Available in sizes 2”, 3” and 4” in NACE and Non‐NACE configurations. NPST Pipes are available in Detachable and Non‐Detachable with a uniform bore in a variety of lengths up to 15,000 PSIG. Available with upgraded DC15 Connections as well.

A pup joint is a casing or tubing of length shorter than Range 1 with the same thread connection, used to adjust the length of tubular strings to its exact requirement.

Pup Joints are manufactured from AISI 4145H or 4140H-modified alloy, heat-treated to a Brinell Hardness range of 285-341 with a Charpy “V” notch minimum impact strength of 40 ft/lb at 70° F and one inch below the surface. Pup Joints are heat-treated to 110,000 PSI minimum yield. All connections are phosphate coated to impede galling during initial make-up.

Integral Pup Joints dedicated to Sour Service applications are available. PJ -110 PUP S are Sour Service Pup Joint using ASCOWELL C material providing improved resistance to Sulfide Stress Cracking with high yield strength.

40 FPS Size and Model ID (IN) FT3/MIN GPM BBL/MIN M3/MINSwivel Joints3/8" & 1/2" High Pressure 0.547 4 29 0.7 0.113/4" & 1" Low & High Pressure 1 13 98 2.33 0.371-1/4" High Pressure 1.375 25 185 4.41 0.71-1/4" & 1-1/2" Low Pressure and 1-1/2" High Pressure 1.5 29 220 5.25 0.831-1/2" HP10 1.593 33 249 5.92 0.941.5" LS-15, 2" LSG-15 & LS-20 1.3 22 165 3.94 0.632" LS-15 1.875 46 344 8.2 1.32" Low & High Pressure 2 52 392 9.33 1.482-1/2" High Pressure 2.5 82 612 14.6 2.323" LSG-10 & LS-15 2.75 99 741 17.6 2.83" High Pressure 2.968 115 863 20.5 3.272-1/2&3" Low Pressure, 3" LS-20 LSG-15 TSi-20 3 118 881 21 3.343" TSi-15, 3" TSi-10, 3" TSi-6 2.75 99 741 17.6 2.84" HP6, FS-4 3.438 155 1,157 27.6 4.384" HPTL, 4" TSi-15 3.5 160 1,200 28.6 4.544" LS-10 3.875 197 1,470 35 5.574" TSi-10 3.75 184 1,377 32.8 5.214" High Pressure 4 209 1,567 37.3 5.935" High Pressure 5.188 352 2,636 62.8 9.986" Low Pressure 6.083 484 3,624 86.3 13.728" Low Pressure 8 838 6,267 149 23.72Pup Joints1" 1502 Integral Pup Joint 0.875 10 75 1.79 0.281.5" 1502 Integral Pup Joint 1.3 22 165 3.94 0.632" 602, 1002, 1502 Integral Pup Joint 1.75 40 300 7.14 1.142" 2002, 2202 Integral Pup Joint 1.3 22 165 3.94 0.633" 602, 1002, 1502 Integral Pup Joint 2.75 99 741 17.6 2.83" 2002, 2202 Integral Pup Joint 3 118 881 21 3.344" 602, 1002 Integral Pup Joint 3.875 197 1,470 35 5.574" 1502 Integral Pup Joint 3.5 160 1,200 28.6 4.542" 602, 1002, 1502 NPST 1.75 40 300 7.14 1.143" 602, 1002, 1502 NPST 2.625 90 675 16.1 2.554" 602 NPST 3.75 184 1,377 32.8 5.214" 1002 NPST 3.5 160 1,200 28.6 4.544" 1502 NPST 3 118 881 21 3.34 Flow Rates at Maximum Recommended Velocity of 40 FPS Size and Model ID (IN) FT3/MIN GPM BBL/MIN M3/MINPlug Valves1" DR150, 1" ULT150 0.875 10 75 1.79 0.281-1/2" DR150 1.3 22 165 3.94 0.631"x2" DR150, 1"x2" ULT150 0.875 10 75 1.79 0.282" DR50 thru DR150 1.75 40 300 7.14 1.142" DR200 1.3 22 165 3.94 0.633" ULT150 2.75 99 741 17.6 2.83" ULT200 3 118 881 21 3.344" ULT100 3.875 197 1,470 35 5.574" ULT150 3.5 160 1,200 28.6 4.54Swing Check Valves1.5" 1502 1.3 22 165 3.94 0.632" 1502 1.75 40 300 7.14 1.142" 2002, 2202 1.3 22 165 3.94 0.633" 602, 1002, 1502 2.75 99 741 17.6 2.83" 2002, 2202 3 118 881 21 3.344" 1002 3.875 197 1,470 35 5.574" 1502 3.5 160 1,200 28.6 4.54

In the oil and gas drilling industry, the tubing pup joint is a critical component for the completion of a well. The pup joint allows the driller to change out the drill pipe without having to pull out the entire string of pipe from the well. This is a common practice, especially when drilling deep wells. Because of this, the tubing pup joint is one of the most important joints in any well.

Tubing pup joints are small-diameter tubing that is used in conjunction with casing to complete a well. The pup joint is run in the hole and cemented to the casing, and then the production tubing is run over it and attached. This arrangement allows for the use of smaller-diameter production tubing, which results in less pressure drop and improved production. The pup joint is usually located in the last few feet of the tubing string.

When you need tubing pup joints, Action is the only source you need to know.Westcan Oilfieldhave awide selection of productsto meet your needs and we offer some of the best prices in the industry. You can trust that we’ll provide you with quality products that you can count on.

Integral → The pup joints are one-piece construction made from alloy steel and feature wing union end connections that eliminate welds and threads. The pup joints are capable of handling a variety of fluids and a working pressure of 15,000 psi. Available in lengths up to 15 feet, they are pressure rated to 10,000 psi for sour gas service.

Pup Joint Inc. is a machine shop that sells down hole tubular and casing accessories and equipment. We are a leading supplier of pup joints & accessories with API5CT & premium threads at very competitive prices. Our machine shop is a threading facility for all your threading & precision machining needs. PJI commenced operations in Houma, LA in July of 1997. Our staff has over 65 years of combined experience supplying quality products & services to the oil & gas industry.