air compressor safety valve leaking supplier

If the tank is over pressurized, the pressure switch isn"t shutting off the motor when the air tank fills to the cut-out pressure. Move the pressure switch lever to the off position. If the compressor continues to run, replace the pressure switch, because the switch isn"t shutting off the compressor motor.

If the compressor shuts off when you move the pressure switch lever to the off position, pull the safety valve ring and release all air from the tank. Switch the pressure switch lever to the on position and allow the tank to fill. If the compressor doesn"t shut off when the air tank fills to the cut-out pressure, replace the pressure switch, because the switch isn"t shutting off the compressor motor when tank pressure reaches the cut-out pressure.

If leaking seals and service bills are distressing your compressor, it"s time to face the fix. While air compressors can be as diverse as the individuals that use them, most models share some general characteristics and components. Whether you are inflating your tires or creating empires, eReplacementParts.com provides the parts, procedures and facts you need to fearlessly fix what fails you.

The safety valve is designed to keep the air compressor pump from over-pressurizing the tank. Over time, the spring inside this valve can deteriorate, allowing air to escape at too low of a pressure. Safety valves are preset to very specific pressure tolerances, so it is important to match the specifications of your specific compressor model when replacing the safety valve.

Less than impressed with your compressor? Replacing the safety valve may be the solution. This article will show you how to complete the repair like an expert technician.

Always depressurize the tank before servicing an air compressor. To do this, open the drain valve and wait until all of the air (and pressure) has escaped.

A well-maintained air compressor can mean the difference between performance under pressure, and under-pressured performance. But you don"t have to empty your pockets to keep your air tank full. As you just learned, repairing your air compressor is simpler than you think, especially when you follow our step-by-step guides. Not only did you refresh compression at a fraction of the cost of replacement; you have inflated your ability to fearlessly face the next fix, regardless of the pressure involved.

An air compressor check valve is a device that allows fluid or air to flow in only one direction. When your compressor reaches the unload pressure, the check valves closes to prevent backflow of the air from the tank to the compressor head.

A quick note on check valves: Many times people will find air leaking from the pressure switch. When this occurs, they immediately purchase and install a new pressure switch. Because air still leaks, they call and state that the switch is defective.

If air is leaking consistently, the problem is not the pressure switch - it is the check valve. More than likely it is filled with debris and is not sealing. When this occurs the check valve either needs to be cleaned or replaced.

Any place that you would have high pressure, you will also need a pressure relief valve (also known as a safety valve). A pressure relief valve releases air smoothly and consistently into the atmosphere from the compressor tank if the air pressure becomes too much.

Generally a relief valve will have male threads on one end, with a ring on the other end (as displayed in the photo). By pulling the ring, you are releasing compressed air into the atmosphere in a safe manner. It is pretty rare that you will ever have to use a PRV, but it is necessary to ensure safety.

An air compressor pressure switch is an instrument which senses a change in pressure and automatically adds or decreases air in the tank. Most homeowners simply know the pressure switch as the device that contains the on/off lever.

Certain air compressors have specific pressure switches that are designed specifically for the machine. Campbell Hausfeld is one company that makes uses a specific switch for each of their compressors. The CW301300AJ kit is by far the most popular.

There are also more generic pressure switches that vary depending on what your cut-in and cut-out pressure is. The photo to the right displays a typical pressure switch that is common on many homeowner style compressors. The small red piece at the top is the on/off switch for the machine.

Depending on the type of compressor you have, an air compressor belt is an essential component of your machine. Most homeowner and smaller handcarry compressors do not use a belt. When you get involved with wheelbarrow or stationary compressors, belts become necessary (especially with virtually all Ingersoll Rand air compressors).A belt works with the pump to help spin the motor to the correct horse power.

Sizes and styles vary across the board. Everything from grooves, length, and width will change depending on the type of compressor that you have. To help find the correct belt for your compressor, we recommend finding you model number and giving us a call.

Generally, most air compressors come complete with two pressure gauges. Most will have one gauge near the pressure switch to display thepressure setting, and another gauge to indicate the air pressure in the tank.

Although an air gauge may not seem like an extremely important part - it is. Having a broken or non functioning gauge means that you will not know the pressure setting at your application, which can result in the incorrect use of your tools.

Simply put, the unloader valve unloads air when the receiver reaches its set point. Most of the time an unloader valve is located at ornear the pressure switch, and when the switch is turned either on or off, the unloader valve is either opened or closed.

There are many different varieties of unloaders available. They will vary by the type of compressor as well as the manufacturer. By givingus a call at 1-866-208-2797, we can generally let you know what type of valve is necessary.

Intake filters are pretty much self explanatory. They filter the air for the first time as it is brought into the system. These are very important to your compressor system, and the operator needs to ensure that they are clean and free from debris.

In-line filters are placed throughout the piping system to ensure that clean air is reaching the end product. It is pretty rare for homeowners and people with small consumer grade compressors to use an in-line filter. In industrial applications they become much more common. Using an in-line filter will make sure that the end line is free from particles and debris,which will ensure that your compressor tools and attachments will last for many years to come.

Generally this will only apply if you have an industrial or stationary compressor. Homeowner and small contractor compressors do not have auto-drains available, as they are all manualdrains. There is a drain on the bottom of the compressor, which should be opened every two days at a minimum (generally once a day is a good idea). this drain helps to remove any waterfrom the compressor tank. If water is left for long periods of time, rust will start to accumulate in the tank.

An auto drain eliminates the need to manually drain the tank every day. It is equipped with a timer that automatically opens the drain at a set time each day. Lets face it, people can forget and mistakes can be made. Therefore, an auto drain is almost always recommended for applications that require consistent air. It makes life easier and helps to prevent mishaps from occurring.

There are various types of gaskets that are used on compressors depending on what type of compressor that you have. Industrial compressors may have head gaskets, cylinder gaskets, etc, while homeowner compressors may use none at all. These gaskets help create a seal when two items are placed together, such as sealing the cylinder head to the valve plate assembly. Many times these are all combined together in one gasket kit.

Each type of gasket will vary depending on the model and manufacturer of the compressor that you have. One of the best resources that you can find with the correct gasket that you need would be the owners manual of your compressor. Of course, you can always call 1-866-208-2797 with your serial and model number, and we can find the correct part for your compressor.

Vibration pads are pretty self explanatory and simple. These pads are small pieces that are made out of various materials (often cork), which are placed under each foot on the air compressor. They are then screwed into the ground with the air compressor, and helps to reduce the amount of vibration and rattling that occurs. It reduces the amount of contact that the compressor has with the ground, and depending on the surface it will reduce noise and lengthen the compressor"s life.

What happens when you pressurize an air tank beyond its rated pressure? It fails catastrophically and ruptures in a spectacular way that you wouldn’t want to witness firsthand.

Most air compressors have a number of precautions built in to avoid the risk of a tank rupture. The compressor itself will probably have an automatic shut-off control that turns off the motor once the maximum tank pressure is reached.

In case the auto-shutoff switch fails, there will typically also be a safety valve built into the tank. Such safety valves, such as the Conrader hard seat valve shown above, are rated to specific pressures. A 100 PSI valve will open up at ~100 PSI in order to vent excess air to keep the pressure at or below 100 PSI.

Essentially, safety valves have spring-loaded pistons. Below their factory-set pressures, internal springs hold the pistons downward, creating a seal. But once the pressure inside a tank or device overcomes the built-in pressure limit of a safety valve, the piston is pushed upwards, opening the valve seal to lower and equalized the air pressure.

Safety valves typically also have loops attached to the pistons so that you can manually rapidly depressurize a device or air tank. You should check safety valves every now and then to ensure they can open freely.

There are two main types of safety valves – hard seat and soft seat valves. Hard seat valves are rugged and inexpensive, but typically leak a little bit. Soft seat valves are a little less rugged and more expensive, but they are built with better seals that aren’t as prone to leaking.

I went with Conrader hard seat valve for a recent project, but there are other good brands as well. Safety valves are available in a wide range of pressures and in different styles.

Amazon carries a couple of valves directly and through 3rd party vendors, but your best bet is to check with Grainger, Zoro, McMaster Carr, or another industrial suppliers that have wider selections.

You may not worry often, if at all, about whether or not your air compressor is running safely. And you really don’t have to, because compressor manufacturers do. From the pressure rating on the air storage tank to emergency stop buttons, air compressors are designed with safety in mind.

But that doesn’t mean you should never think about your compressor’s safety features. In most cases, they need to be inspected regularly to make sure they’re working properly. One key safety feature that should be inspected regularly is the air pressure relief valve (PRV), sometimes called a safety relief valve.

The pressure relief valve is a safety valve that protects the compressor component that it’s attached to from being exposed to a pressure above its rated maximum operating pressure. This rating, called the maximum working pressure (MWP), is the pressure that the vessel has been certified to continuously operate at safely.

So when a compressor is running at or below its maximum working pressure—in other words, when it’s running “normally”—the relief valve doesn’t do anything.

However, when the air pressure inside a compressor exceeds its MWP, the pressure relief valve will activate to “blow off” the excessive pressure within the compressor. Without a relief valve, the storage tank could rupture from the excessive pressure, damaging the compressor itself, possibly other property near it, and even causing injuries (or worse) to anyone standing nearby.

Before we can talk about how the air pressure relief valve works, we first need to look at how air pressure inside a compressor is managed when everything is running normally.

Under normal circumstances, the air pressure in a compressor is controlled by a pressure switch in an electro/mechanical control system or, in the case of an electronic controller, a pressure transducer and controller settings. When the cut-out set pressure for the pressure switch is reached, the compressor will stop compressing air (unload) until the cut-in set pressure is reached, at which time it will start compressing air again (load). If the pressure switch fails, the compressor would not be able to start compressing air again, or potentially worse, not be able to stop. Most compressors also have a high-pressure safety switch that should stop the compressor if the pressure exceeds the unload set point.

A pressure relief valve is a straightforward safety backup to the pressure switch and high-pressure switch, or the controller set points, should any of these components fail with the compressor running. The safety relief valve is set above the high-pressure safety switch and generally at or below the vessel’s maximum operating pressure. Inside the valve is a spring, and the pressure created by the spring’s tension keeps the valve closed under normal operating conditions. However, as the air pressure increases in pressure vessels (like the storage tank), it eventually exceeds the rated pressure of the relief valve, causing the relief valve to open and the excess pressure to be “blown off” to the atmosphere.

If the pressure relief valve fails open, air will continually vent to the atmosphere, preventing the air stream from becoming fully pressurized. The compressor should be shut down and the relief valve replaced before the compressor is restarted. The open relief valve will likely cause a loss of production and possible danger to personnel as a result of the flow of high-pressure air with flying debris and an unsafe sound level.

A pressure relief valve failing closed presents a potentially more dangerous situation. As noted earlier, the relief valve exists to allow excessive pressure to be “blown off” so that the air pressure inside the compressor’s pressure vessels don’t exceed their rated specifications. If the valve fails closed, this pressure venting can’t happen. Unless compressed air demand matches the compressed air supply, the pressure inside the compressor will continue to build. Eventually, the pressure increase would cause the storage tank to rupture, damaging the compressor and possibly causing additional damage and injury to property and people nearby.

If the relief valve is opening because the air pressure in the compressor has exceeded the valve’s pressure set point, that means the valve is working and doing what it was designed to do. But because this indicates the MWP of the compressor has been exceeded, the condition that’s causing excessive pressure should be diagnosed and corrected.

If the relief valve opening wasn’t caused by excessive pressure inside the compressor, then the valve is most likely “failing open”. Most likely, this is because the valve has become “soft” over time, i.e. the valve spring is providing less counterpressure, so it’s opening at a lower pressure than it should.

Whether the valve opened because of excessive pressure in the compressor or because the valve is failing, you should have your local air compressor distributor inspect your compressor before running it again for two reasons:

First, your distributor can determine whether the valve opened due to a failing relief valve or excessive compressors pressure and perform any needed maintenance or service to get your compressor running efficiently and safely again.

Second, regardless of why the pressure relief valve opened, replacing it may be recommended to ensure safe compressor operation, depending on the valve manufacturer. (Replacement is recommended for Sullair compressors.)

Important: Running the compressor after the relief valve has opened, regardless of the reason why it opened, can put both your property at risk of damage and people at risk of injury (or worse). While this may be obvious if the compressor is building up excess pressure, it also applies if the valve failed open. As noted above, even a valve that fails open poses some risk, and next time it could fail closed.

Given how critical a working air pressure relief valve is to the safe and efficient operation of your air compressor, you may wonder whether you need to do any regular inspecting or testing of the valve to make sure it is working. Because this can vary by manufacturer, you should consult your owner’s manual or contact your local air compressor distributor for frequency and type of inspection needed. For most Sullair compressors, inspection for damage or leakage is recommended, but testing is not recommended, as doing so may compromise the valve’s performance.

However, one thing you should do is schedule regular maintenance with your local air compressor distributor. As part of regular maintenance, a service technician can inspect the PRV and let you know it’s at an age or in a condition at which the manufacturer recommends replacement. Also, problems with the compressor’s performance, e.g. not reaching normal operating pressure, may help the service technician identify a failing relief valve after ruling out other possible causes.

When a pressure vessel like a receiver, sump tank or other storage vessel is purchased separately from the compressor, it may not be supplied with a pressure relief valve. To ensure its safe operation, you should add a PRV.

When selecting a PRV to add to the pressure vessel, you must choose a valve with a pressure set point set at or below the maximum working pressure of the vessel. You will find the MWP (and other useful information) on a tag welded to the pressure vessel. Also, flow capacity of the PRV must meet or exceed the total compressed air supplied to the vessel.

For example, if you have two compressors with capacities of 500 and 750 cfm (14.2 and 21.2 m³/min), and a pressure vessel with a maximum working pressure of 200 psi (13.8 bar), the minimum settings for a pressure relief valve would be 1250 cfm (35.4 m³/min) and a set point 200 psi (13.8 bar) or less.

Finally, when attaching the valve to the vessel, the porting must not be reduced to a size less than the size of the inlet port of the pressure relief valve.

Because the pressure relief valve is critical to the safe operation of your compressed air system, if you’re not sure how to select the correct PRV and properly and safely add it to the pressure vessel, contact your local air compressor distributor. They have the experience and expertise to ensure that the PRV is sized and installed correctly.

Conventionally when we talk about oil lubricated screw air compressor maintenance, it is mostly about replacing consumables such as filters and lubricant on time. While these consumables have a defined usable life and have a direct effect on the efficiency and the life of the air compressor itself when not replaced on time, there are a few critical valves in the air compressor that require maintenance as well. Compressor valves directly affect the efficiency, safety, and the functionality of the screw air compressor. Let us understand some of the commonly available valves in a screw air compressor, why they need maintenance, and discuss some of the frequently asked questions about screw air compressor valves.

A screw air compressor is very similar to a human heart. While a human heart has tricuspid, pulmonary, mitral, and aortic valves, a screw air compressor has four critical valves namely air inlet, minimum pressure, blow down, and safety valves.

Air inlet valve is also commonly known as the ‘Intake valve’ which is typically assembled on the airend’s intake. The air inlet valve of a conventional fixed speed screw air compressor controls the air intake into the compressor. It remains closed when the compressor starts to lower the starting load on the main motor and when the desired working pressure is attained in the compressed air circuit and thus enabling the compressor’s motor to run without any load. In some compressors that are capable of providing a variable output by modulating the amount of air it sucks in, the inlet valve holds various opening positions to regulate the volume of air entering the compressor. The effective performance of the inlet valve directly affects the compressor’s capacity and its power consumption during load and no-load conditions.

The minimum pressure valve is typically assembled on the exit of the air-oil separation tank of a compressor. The minimum pressure valve acts as a check valve preventing back flow of compressed air into the airend, retains a minimum pressure in the compressor system for lubrication, offers a restriction to avoid a collapse of the air-oil separation filter, and ensures a suitable velocity of flow across the air-oil separator that ensures efficient air-oil separation. The effective performance of the minimum pressure valve directly affects the compressor’s lubrication, air-oil separation efficiency, and power consumption during load and no-load conditions.

The blow down valve is typically found on a dedicated exhaust line from the air-oil separation tank. The blow down valve evacuates the compressed air in the air-oil separation tank each time the compressor runs on a no-load and when the compressor shuts down to ensure there is no back pressure when the compressor starts to load next time. The blow down valve of a conventional screw compressor is typically actuated by a solenoid valve. The effective performance of the blow down valve affects the compressor’s power consumption during un-load, capacity of the compressor when running on load, and the life of the motor.

The safety valve is typically mounted directly on the air-oil separator tank. The only function of the safety valve is to blow off the compressed air in the air-oil separation tank when the pressure in the air-oil separation tank exceeds the set pressure of the safety valve and there by prevents the tank from cracking under high pressure. A malfunctioning safety valve affects the safe operation of the air compressor or results in leakage of compressed air continuously.

Though each compressor manufacturer has their own unique valve design, compressor valves in general contain moving parts such as springs, valve plates, and plungers that affect the opening and closing of the valves and rubber seals / seats that offer perfect sealing when the valves remain closed. These moving parts wear or lose their mechanical properties over a period of time and the sealing components typically ‘age’ over time and lose their effectiveness and will need to be replaced.

Compressor manufacturers typically design these components to operate efficiently for several thousand or millions of operation cycles. However, several factors such as variability in the demand pattern, sizing of the air compressor against a certain air demand, the environment in which the air compressor operates, promptness of preventive maintenance, etc. determine how long these valves efficiently operate.

Many times, it is difficult to identify a malfunctioning valve or a valve operating with worn-out parts as the compressor continues to generate air. The typical symptoms of a malfunctioning valve are loss in compressor"s capacity, increase in power consumption during load or/and unload, drop in discharge pressure, increase in oil carry-over and more load on motor. These symptoms are either difficult to notice or have other frequently common assignable causes such as air leak before suspecting the compressor valves.

Case studies show that operating a screw air compressor with a worn-out / malfunctioning valve could increase its overall power consumption by 10 - 15%. Power cost contributes to more than 75% of the compressor’s total life cycle cost over ten years and hence this is a significant impact. Unserviced valves also lower the life span of downstream accessories by half. In some cases, a malfunctioning safety valve may result in a catastrophe.

Air compressor manufacturers typically offer convenient valve maintenance kits for customers that contain the internal parts of the valve that wear or age out. Changing the valve kits is a much more sensible and economical option than changing the complete valve.

It is difficult or almost impossible to identify a malfunctioning valve unless it is opened for inspection. Hence it is absolutely mandatory that these valves are inspected for effectiveness every year and the internal moving parts replaced as a part of preventive maintenance once every year or two depending on the operating conditions of the air compressor. It is typical for compressor manufacturers to mandate a valve kit replacement once every two years as a proactive measure.

In particular, the safety valve must be inspected and certified every year per the local safety laws to ensure they are functional and efficient. Sometimes, replacing the safety valve entirely with a valid certificate for one year is more economical as the certification procedures could be equally expensive on an existing valve.

As stated before, it is challenging to identify a valve that is worn out unless it is opened and inspected, but there are a few indicators that a qualified compressor technician can use to deduct a malfunctioning valve.

Low duty cycle operation: A sophisticated screw air compressor in today’s day and age carries a convenient microprocessor-based human-machine interface that keeps track of operating hours of the compressor under load and un-load conditions and the number of load/unload counts the compressor is subjected to over a period of time. A higher un-load hours and load/unload count indicates that the air compressor is oversized against the actual air demand. This in turn indicates the air compressor ‘cycles’ frequently between load and un-load mode as opposed to running continuously on load. Every time a compressor ‘cycles’, the inlet valve, blow down valve, and minimum pressure valve is brought into play where their internals ‘actuate’. Frequent actuation of these valves results in a faster wear of the internals and hence results in shorter life.

High operating temperature: A compressor that runs on a high operating temperature affects the life of the valve’s sealing components, which causes them to ‘age’ fast.

Compressor not building pressure: If the air demand has not changed over time and the facility is relatively free of any air leakage, the air compressor is probably not delivering the rated output. There is a high probability that there is a malfunctioning valve.

Increase in compressor’s power consumption: An increase in the air compressor’s power consumption profile over a period of time where there has been no abnormal change in the air demand and usage pattern indicates an increase in either the load or un-load power. There is a high probability that this is because of a malfunctioning valve.

Based on the design philosophy adopted by the air compressor manufacturer, the oil lubricated screw air compressors could have a few more valves that are critical to functional performance that must be maintained as well. Some of the other valves frequently used in an air compressor are as follows:

Temperature control valve (also known as thermal valve) is used to regulate the flow of oil through the oil cooler based on the operating temperature.

Drain valves are used to drain lubricant at the time of lubricant change over or cleaning. Air compressors equipped with a moisture trap at the outlet of the after cooler also has a drain valve (automatic or timer based) to discharge water collected.

The presence or absence of one of these valves and the type of actuation of these valves (electronic / mechanical) depends on air compressor’s design architecture. The Operation and Maintenance Manual (OMM) and the Piping and Instrumentation Diagram (P&ID) supplied by the air compressor manufacturer are excellent resources that explain the purpose, functioning, and maintenance requirements of these valves.

Many of the air compressor valves are highly specialized and exclusive. Their designs are usually complex and some even need special tools to service them. The internal components" build quality and material selection are extremely important and proprietary. Hence it is highly critical that only genuine valve kits issued by the air compressor manufacturer are used to maintain the valves. An inferior after-market replacement will most certainly compromise the performance of the entire compressor, void the original manufacturer"s warranty of the compressor, cause consequential damage to other parts of the compressor, and above all, be a safety hazard.

In conclusion, while it is important to change the screw air compressor"s filters and lubricants on time, it is equally important to perform preventive maintenance on these critical valves in a screw air compressor as recommended by the air compressor manufacturer. While the intake valve, minimum pressure valve, safety valve, and blowdown valve are critical to the performance and safety of the compressor, there could be other valves in the compressor that are critical and need maintenance. The air compressors sizing and the environment in which it operates are crucial factors that affect the life of the air compressor. Finally, it is critical to proactively service these valves using genuine kits issued by the compressor manufacturer to enable the air compressor performs efficiently and safely.

Gershom Joel has over 15 years of experience in the compressed air field and specializes in helping industries such as Pharmaceuticals, Textile, Electronics, and Food and Beverage find compressed air solutions to meet their unique requirements.  Gershom holds a Mechanical Engineering Degree from Anna University and a Masters in Business Administration from University of North Carolina.

ELGi North America, headquartered in Charlotte, NC, is a subsidiary of ELGi Equipments Limited, a leader in compressed air solutions for over 60 years. Established in 2012, ELGi North America, in conjunction with its subsidiaries, Pattons, Pattons Medical, and Michigan Air Solutions, offers a comprehensive range of compressed air products and services. Our product offering includes oil-lubricated and oil-free rotary screw and reciprocating compressors, dryers, filters, and ancillary accessories. ELGi and its subsidiaries serve multiple industry verticals spanning medical applications, pharmaceuticals, food & beverage, construction, manufacturing, and infrastructure. For more information, visit https://www.elgi.com/us/.