ge oven safety valve in stock

GE gas range oven safety valve for round ignitors. 3.3 - 4.0 volts. 2.5 - 3.0 amps. Valve has male wire terminals. Reference number 164D2574G001 and 30100-17. ... More Info

GE gas range oven safety valve. This is a dual valve. 1/4" male terminals on top. 3/16" male terminals on bottom. Reference numbers 223C3389G001 and Y30148-14. ... More Info

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Low voltage, oven safety valve with female wire terminals for a flat ignitor. This gas oven safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.

3/8" Oven safety valve with male wire terminals for a flat ignitor. This gas oven safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.

3/8" inlet Oven safety valve. This gas oven safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.

Dual terminal Oven safety valve. This gas oven safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.

Oven Ignitor (Round Glow Bar) for GE JGBS22GEV4AD Range - Oven/Stove. Genuine product manufactured by GE. Round style Oven/Broiler Igniter, includes High Temp Wire Nuts and Instructions. Ranges from 2.5 - 3.0 amps. This will not replace flat style ignitors. Caution the center coil is VERY fragile.

Oven Ignitor (Round Glow Bar) for GE JGBP28GEV3WH Range - Oven/Stove. Genuine product manufactured by GE. Round style Oven/Broiler Igniter, includes High Temp Wire Nuts and Instructions. Ranges from 2.5 - 3.0 amps. This will not replace flat style ignitors. Caution the center coil is VERY fragile.

Thank you for your inquiry. The oven safety valve is one part that may fix the issue, but there are some other parts that you will need to check to see which one is causing the issue. You will need to check the igniter, the electronic control board and the temperature sensor. I hope this helps. Thank you and have a great day!

Can this oven valve work on my range? The range was plugged into the wrong outlet and it shorted out, the igniter glows when the stove is turned on however the burner isn"t lighting. I was told the the valve needs to be replaced.

Thank you for your question. This is not the correct safety valve for your appliance. I have listed the correct valve below for you. I hope that helps. Good luck with your repair.

Oven doesn"t heat. Igniter glows when gas is turned on, voltage on value starts near zero and slowly ramps up to just under 3 volts, but gas never ignites. The slow ramp seems normal to allow igniter to get hot, but not sure what the valve"s voltage should be to have it open. Valve coil is not open per ohm meter. Sounds like a bad valve? Thanks.

Hello Curt, Thank you for your inquiry. It sounds like it could be either this part or the pressure regulator. When the ignitor heats up to a certain temperature, it is supposed to trigger the valve to open and let the gas in to ignite and the regulator cuts it off at a certain pressure. Hope this helps!

Hello Sal, thank you for your question. You can test the gas valve to see if it has gone bad. You will need to test this with a multimeter. Here is a video that will show you how to test that valve.

Hello Steve, thank you for your question. The oven safety valve part number WB19K31 will work with either NAT or LP gas. The part itself can be switched over without any additional parts. Please check your owners manual on steps to change that over. I hope this helps!

In the oven a wire from the igniter shorted (had to pry the wire off the wall) to the frame. Would the control valve or the thermostat also be damaged. Where is the thermostat located on the stove. I noticed that the plastic on one of the knife connection on the control valve was missing

Hello Robert, thank you for writing. It is doubtful that the Oven Safety Valve or Oven Thermostat were also damaged when this occurred. The Oven Thermostat (part PS235170 on your model) is located behind the Manifold Panel (control panel). We hope this helps.

Hi there, i have a GE gas range (model jgbp28sem1ss) and need to replace the safety valve for the part of the oven that bakes. Is this the correct part? Thanks

Antigua and Barbuda, Aruba, Australia, Austria, Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Bermuda, Bolivia, Brunei Darussalam, Bulgaria, Cambodia, Canada, Cayman Islands, Chile, China, Colombia, Costa Rica, Cyprus, Czech Republic, Denmark, Dominica, Dominican Republic, Egypt, El Salvador, Estonia, Finland, France, French Guiana, Germany, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guernsey, Honduras, Hong Kong, Hungary, Iceland, Indonesia, Ireland, Israel, Italy, Jamaica, Japan, Jersey, Jordan, Kuwait, Latvia, Liechtenstein, Lithuania, Luxembourg, Macau, Malaysia, Maldives, Malta, Martinique, Mexico, Monaco, Montserrat, Netherlands, New Zealand, Nicaragua, Norway, Oman, Pakistan, Panama, Paraguay, Philippines, Poland, Portugal, Qatar, Republic of Croatia, Reunion, Romania, Saint Kitts-Nevis, Saint Lucia, Saudi Arabia, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sri Lanka, Sweden, Switzerland, Taiwan, Trinidad and Tobago, Turks and Caicos Islands, United Arab Emirates, United Kingdom, United States