baso h15 pilot safety valve factory

Gas Safety ValvesThese valves automatically control main gas flow. Our automatic pilot valves shut off both the main and pilot gases. Pilot gas is tapped from the main line within the control. Gas will flow only to the pilot burner when the reset button is depressed. The manual pilot valve stop can be adjusted for maximum pilot flow.

Pilot BurnersThese “J Series” combination pilot burners are universal replacement pilot burners and are supplied in three models. Mounting brackets on all four sides of each burner permit adaptation to almost any application. We also offer pilot burner fittings (R Series) and replacement flame sensors and inlet fittings (Y Series).

The H15 Series pilot valves provide safe lighting and complete shutoff of pilot and main burner gas in the event that the flame heating the thermocouple is extinguished. They are designed for standing pilot applications and can be used with natural gas and Liquefied Petroleum (LP) gas, at pressures up to 0.5 psi. Typical applications include commercial cooking equipment, heaters, kilns, dishwashing equipment, industrial ovens, and similar applications.

The H15 Series pilot valves provide safe lighting and complete shutoff of pilot and main burner gas in the event that the flame heating the thermocouple is extinguished. They are designed for standing pilot applications and can be used with natural gas and Liquefied Petroleum (LP) gas, at pressures up to 0.5 psi. Typical applications include commercial cooking equipment, heaters, kilns, dishwashing equipment, industrial ovens, and similar applications.

Control shuts off both main & pilot gas. Pilot gas is taken from within the control. Pilot activated by reset button. For all fuel gases. For full specs on the Baso Gas Products™ valve listed here, download the PDF below.

NOTE: The number (or number and letter) that appear after the model number (such as H19RA-2C) apply only to how the valve is packaged from the manufacturer. So, an H19RA-1 is the same exact valve as a H19RA-2C... it is just packaged differently.

This week’s blog pick of the week is the BASO replacement parts. The reason behind this manufacturer has been picked as they are one of the best suppliers of the commercial pieces of equipment and many business owners are using their product for the last few decades. And now there is a demand for the BASO parts for maintenance purpose. So we are recommending the PartsFPSfor your need for replacement parts for your commercial kitchen.

It is a good idea to learn a little bit about the workings and possible problems that can crop up, to take proper care of your BASO equipment. If the problem is simply one then it means you can carry out some quick DIY.

But to repair your oven, you have to buy the perfect BASO part. I can suggest one place where you can get genuine replacements parts but in comparatively less price – PartsFPS. Over costly repairs, after all, good maintenance is always preferable. By not having to call out the technician, you can save the money. Obviously, the exact problems differ from manufacturer to manufacturer but when we are talking about one manufacturer then it is a little bit easy. You can try some of the troubleshooting tips if you are confident enough in your abilities, - try the DIY solutions. Here in PartsFPS, you will get all the genuine BASO replacement parts. at a very less price and we can assure the fast and safe delivery.

BASO evolved as a leading manufacturer of an extensive variety of gas control products and accessories in 1914. But the initially they are known as Milwaukee Gas Speciality Company. But in 1968 Johnson controls Inc has purchased the entire BASO which is already merged with Penn Controls.

In the last 100 plus years, while many things have changed, but the commitment of the BASO to produce superior products remains unchanged. Since 1914 it is serving the restaurant chains outlets with high-quality products.

And now if you are searching for the best quality BASO replacement parts then I must say you are in the right place. As we all know that PartFPS is the leading supplier of the restaurant equipment parts from a wide variety of manufacturers, but the good news is we provide the BASO Parts also. So you also agree with my point that you can get your required parts at a reasonable price. Try our online store for your required BASO Gas Valve Parts.

There are two different types of ignition sources – electronic ignition module and standing pilot. So, to avoid the hazardous situation for the gas safety valves, you have to know how to test the safety valve and secure your safety.

You will need a multi-meter to test the BASO safety valve parts. The valve is not working correctly may be due to the interruptive electric path within the valve. You will need to change the safety valve if the multi-meter is not showing the results between 0-50 resistance. Here we are going to share the most commonly used BASO safety valve parts which we are selling at a vet low price. Scroll down to check the technical details of the BASO parts.

To ensure safe and reliable operation, this BASO H15HR-3 equivalent gas safety valve replaces the faulty gas valve. BASO H15HR-3 Equipment Gas Valve can work with both natural gas and liquid propane.

BASO Safety Valve H15HQ-6 allows the safe lightning as it permits the gas flow only to the pilot burner. You can trust this product as it is proven by thousands of units in service. This automatic BASO H15HQ-6 Equipment Natural Gas Valve provides complete shut-off of the pilot and main burner accompanied by the safe lightning.

BASO H15HR-6D Equipment Gas Valve is compactly designed which helps it in installation in dimensionally restricted applications. Baso oven safety valves are widely used in the variety of domestic and commercial gas burning equipment.

To prevent the appliance from a potential hazard, proper maintenance of the types of equipment is required, it is important to regularly inspect the working condition of the BASO commercial kitchen types of equipment. And your inspection never ends without inspecting the BASO gas solenoid valve parts. Dangerous pressure might build up and cause damage, if solenoid valves are malfunctioning, for solenoid valves malfunctioning, there are 4 possible reasons. They are - coil burnout, failure to open, solenoid valve noise and failure to close. In the first stage of the above-mentioned problems you can troubleshoot the issue by yourself but if the damage is severe then you have to replace the BASO gas Solenoid Valve Parts.

So get the perfect match for your faulty solenoid valve here – PartsFPS. We are the genuine supplier of the BASO Gas Solenoid Valve parts across the globe at a very low price. We ensure you the quick and safe delivery of the product at your door. We share the basic details of few of the commonly used BASO Gas solenoid valve parts.

On a demand signal from a thermostat or other controlling device, electrically operated Baso H91CA-21 Gas Solenoid Valve Part automatically opens and closes. With a maximum operating pressure of 0.5psi, Gas Solenoid Baso H91CA-21 can be used for gas-fired appliances.

Baso G96HGH-5C Equipment Dual Natural Gas Valve ensures a proper gas supply to your equipment. The width of the G96HGH-5C part is 4 1/8” and it needs 25V to perform properly.

For creating the spark that starts your machine, the ignition module is responsible. To begin testing when your kitchen equipment is not working, BASO ignition module is the best point. So the steps to test the Ignition Control Module

If there are no obvious visual signs of damage then test the wiring after switching your motor to the ohm setting. Make sure to check all wiring as replacing the wires are much easier and cheaper than BASO ignition module parts. If your ignition module does need replacement. then choose the perfect match from our online store – PartsFPS. Here we mention few of the widely used BASO ignition modules.

Baso BG1100MAAK-2G Ignition Module is used to replace the malfunctioning one. This BASO ignition module is equivalent to 24V direct spark ignition module. It has 3 trials @5 minutes interval with a 4sec retry. And it has no pre-purge also.

BASO BG1100MAAK-1G is designed for the direct burner supervision. For direct spark ignition boilers, furnace and other heating equipment, the BASO Gas Product Ignition Module provides ignition sequence, flame monitoring and safety shut-off. It is a microprocessor-based ignition control.

The H15 Series pilot valves give complete shutoff of both pilot and main burner gas and safe lighting on different commercial and domestic gas-burning equipment. BASO Safety Valve applications include wall heaters, room heaters, central heating equipment, unit heaters, dishwashers, industrial ovens, and degreasing equipment.

If your appliance has BASO H15CA 5 Safety Valve and wants to replace/ install with the new one, let’s take a look. Here, we help you by providing an installation process of BASO Safety Valve. Moreover, you can follow all the instructions that are provided in the manual.

Guarantee that the main gas move through the gas valve body must be towards the path shown by either "IN" and "OUT" or the arrow on the valve body. If the valve is placed in the opposite direction, then there will be a gas leakage chance.

Attach the BASO Safety Valve to the pipework in any convenient position. Use a suitable pipe joint sealing compound on the male threads before they combine. Remove extra compound after mounting the valve.

Next, attach the thermocouple securely to the pilot burner. Screw the terminal end to the BASO power unit terminal on the valve. Make sure that this connection will be clean.

The H15 Series automatic pilot valves provide safe lighting and complete shutoff of pilot and main burner gas in the event that the flame heating the thermocouple is extinguished. They are designed for standing pilot applications and can be used with natural gas and Liquefied Petroleum (LP) gas, at pressures up to 0.5 psi. Typical applications include commercial cooking equipment, heaters, kilns, dishwashing equipment, industrial ovens, and similar applications.

BASO H15AR3 3/8 180 CFH Safety Pilot Valve. The H15 Series pilot valves provide safe lighting and complete shutoff of pilot and main burner gas in the event that the flame heating the thermocouple is extinguished. They are designed for standing pilot applications and can be used with natural gas and Liquefied Petroleum (LP) gas at pressures up to 0.5 psi (35 mbar [3.5 k