gas oven safety valve troubleshooting quotation

When you turn the dial on your gas stovetop, it opens a valve that lets gas through. This gas is released and mixes with air. It is ignited by a continuous spark which comes from the spark module, and a blue flame is created.

When the electrode on your gas oven burner continues sparking after the gas has been lit, it usually is a sign of a short in the spark module. This usually happens when liquid (like water from an overflowing pot) gets into the spark module. To fix this, unplug your appliance and let the burner dry out. Turn it on again and test it to see if drying has fixed the problem.

If your spark module sends out a spark intermittently instead of sparking at a continuous pulse, it has probably worn out and most likely needs to be replaced. You can call a service technician or your home warranty company to get this repaired. This is not something that you should attempt to repair or replace yourself. Although the cost of the spark module really depends on the oven model the part can be found for anywhere between $30 to $250it"s a better deal to replace one spark module rather than replacing an entire oven. This is especially true if you have a home warranty plan, as the repair will generally only cost a small service call fee.

If you see any damage, call a registered technician or your home warranty company in order to get the electrode replaced. Sometimes, your electrode"s spark is being blocked by the top of the burner being slightly off. Make sure the burner is in the correct place for the electrode to reach the gas and light it before calling a repairman or your home warranty technician.

If you don’t see any cracks on the actual electrode, you can also turn each burner dial to see if there’s one that doesn’t spark. If all of your burners spark but one, there’s probably a problem with the dial. There are times when the dials can become stripped and won’t turn on the electrode. It’s also possible that the dial has shorted out because food or water has spilled into the burner. You can try to dry out the burner, and if that doesn"t work, the igniter wiring harness will need to be replaced. Paying to repair this part is much more cost effective than purchasing a new oven, as the parts range between $30 and $100. With a home warranty, you only pay a small service call fee for parts and labor to repair the igniter wiring harness as long as it"s failed from normal wear and tear.

There’s a chance that food or grease has plugged up the tube that releases gas to be lit by the burner. Turn your oven off and remove the burner from the oven. Clean out thesmall tube inside of the burner with a toothpick or small brush.

When you turn on your oven to bake (or broil) the dial sends electricity to the igniter, which begins to warm up. As the igniter warms, the safety valve releases gas into the oven burner tube. Once the gas reaches the igniter (which can get up to 2,000 degrees Fahrenheit) the gas is lit by the extremely hot metal on the igniter, and warms the oven. When the oven reaches the temperature you selected, the burner and igniter will shut off, but will turn on and off while you’re cooking to keep the correct temperature in the oven.

First, remove the shields so you can see the igniter. If the igniter is glowing, but there’s no flame after the igniter has been glowing for a longer period of time, theigniter has probably grown too old and can’t open the safety valve to bring gas into the burner tube. Call your home warranty company for diagnosis for this problem.

Oven problems can happen to any homeowner, but with some troubleshooting and a home warranty plan from Landmark Home Warranty, you can usually fix small issues or repair or replace the oven. If you"re interested in covering your oven with a home warranty plan, compare Landmark"s home warranty plans here, or download a brochure with our contract for your state here.

The kitchen is the heart of the home. It’s where families share dinner, gather together and pass down recipes. One of the worst things that can happen when preparing to cook an amazing meal for your family is to find out that your gas oven won’t light. Do you call a repairman or resort to the microwave?

A handy homeowner can troubleshoot the problem when a gas oven doesn’t light. A handful of common problems can plague gas ovens. Many are as simple as a loose connection, while others involve replacing important components. However, those simple repairs are less likely to cost you an arm and a leg. Before worrying about replacing your oven, see if one of these common issues is the cause of your oven problems.

You can check a handful of issues if your gas oven doesn’t light. From a simple power issue to a faulty gas igniter, here are a few common reasons your gas oven won’t work.

If your oven won’t heat and your gas burners won’t light, the problem might be as simple as a tripped circuit breaker. Even though you have a gas oven, it still needs electricity to run. Electricity powers the control board, igniter and temperature sensor, among other parts.

The oven should connect to a standard 15- or 20-amp switch inside your circuit breaker box. These are the single switches. Your oven may also have its own dedicated breaker switch. If not, you can check the power by testing the secondary outlet. The problem lies elsewhere if the outlet works but your gas oven does not.

While a rare occurrence, your gas oven may not heat because your gas supply is off — usually a result of maintenance repairs or replacements in the system. For example, if your oven or other gas-reliant appliance was recently repaired, the gas line is likely still turned off.

Like a thermostat, the temperature sensor regulates the oven temperature of your gas oven. It connects to the igniter switch. If the temperature sensor breaks, the oven will not light for safety reasons.

Troubleshooting and replacing this sensor is a fairly easy fix for a homeowner who is comfortable working on a gas oven. Unplug the oven from the wall.

The igniter controls the oven safety valve, also known as the gas valve. This oven component ensures only gas enters the oven when the igniter is hot enough to ignite it. This component stops working if there is not enough power to either the valve or the igniter. A handy homeowner can use a multimeter tool to test that the valve is working. Unplug your oven.

Use a multimeter tool on the RX1 setting and test the valve. Some brands use valves with terminals for both the broiler and the baking elements. Test both sets of terminals.

The igniter is the key component of a gas oven. If you have a faulty igniter, many of the other components will not work and the oven will not turn on. Oven igniters glow hot to ignite the natural gas released by the oven safety valve. However, if the heating element is not working, the gas valve will not trigger and the oven will not ignite.

To check the gas igniter: Turn off the circuit to the oven and confirm the power is off by checking that the oven light, clock and control board are all off.

If nothing looks wrong with the part, plug the oven back in and watch to see if the igniter glows after turning on the oven. If it does not glow orange, replace it.

Replacing a faulty gas oven igniter is a moderately easy DIY appliance repair. Estimated costs are between $40 and $80, depending on the cost of a replacement igniter. If you have a newer oven, check any manufacturer warranties before making any repairs.

While a homeowner can do this project, ensure you take every safety precaution before attempting. Turn off the oven’s gas supply and disconnect the appliance from the outlet. Remember to take precautions if you smell gas (even after you have turned off the supply to the oven). Turn off the main gas supply to your home, open windows for ventilation, and call an appliance technician for assistance.

To ensure you have the correct replacement igniter, have your oven model number and serial number. A Kenmore oven might not use the same part as a Whirlpool oven. These numbers are often found inside the oven door or drawer, depending on the brand of oven.

Turn off all power to your oven. Ensure the power is off by checking that the light, control board and clock are off. Then remove the oven racks. Next, unscrew the base plate and remove it from the oven. You will find the igniter underneath.

Take a reference photo before removing the old gas igniter. Install the new igniter in the same way. Be very careful with the new igniter because it is very fragile. Unplug the two wires or the wire harness from the igniter.

While your gas stove and gas oven are part of the same appliance, they do not use the same parts and components. This is why your gas burners can work while your gas oven won’t light. Your gas range has its own set of igniters, gas valves and safety features. If everything is in working order, your range can work independently of your gas oven.

Appliance repairs are always a big inconvenience and can sometimes cost an arm and a leg. Don’t get stuck without your most important appliances. Check out the Cinch Home Services warranty plan that cover appliances, including both gas and electric ovens. With three different options to choose from, you can find the right plan for your home.

The last thing a restaurant owner needs is a problematic gas oven. To ensure that such issues are resolved quickly – and the oven once again works like it should – you’ll need to determine what’s causing the malfunction in the first place. Only then will you be able to decide on the most appropriate solution. Cafco Services, one of the area’s premier hot side and HVAC installation companies, shares what you need to know here.

The pilot light won’t ignite. This issue occurs when the thermostat is positioned incorrectly. Because the component isn’t directly in the flame when lighting the pilot, it won’t be hot enough to open the safety valve. Most of the time, having the thermocouple adjusted properly will resolve this problem. But there are, however, cases where the component itself is broken and will need to be replaced by an authorized expert.

The gas oven isn’t hot enough. It could be that the thermostat is out of calibration, so check the operations manual and follow the calibration procedures. Another reason might be a broken thermostat, in which case you’ll need to call a reliable hot side and HVAC repair company like Cafco Services for a replacement.

The gas oven is too hot. You may have set the temperature too high, so crank it down a little. If that’s not the problem, the thermostat is either out of calibration, which means you’ll need to troubleshoot it following the manufacturer’s calibration procedures, or it’s damaged. If this is the problem, turn to an authorized technician to get it replaced.

The oven isn’t heating. You might want to have a trusted local hot side technician check the unit if it’s switched on but not running. It’s likely that the gas oven has a broken power switch that may need to be replaced. Examine the oven door for a cracked gasket or damaged hinges or microswitch. If the door doesn’t close all the way, the unit may refuse to switch on. This will likely require repairs from your local technician.

Gas stoves and ovens undergo a lot of wear and tear from everyday use. Quality appliances are built to last, but frequent exposure to high temperatures means even the most reliable appliances require regular maintenance.

There are some telltale warning signs that suggest when gas appliance repair service or maintenance is required. This article will review what you should watch out for.

The noxious odor of gas is, of course, an obvious sign that something is wrong. Agas leak is a dangerous situation and should be remedied immediately.

The smell of gas could suggest a faulty igniter, broken gas line, or faulty valve. If you smell gas only when you turn the appliance on and notice the stove or oven doesn’t create a flame, then the igniter is probably faulty. If you smell gas when you’re sure the appliance is off, a bad gas line or valve is the likely problem.

Most gas appliances have a shut-off valve at the rear of the unit. Turn the valve to cut the gas from the source. If the odor persists, there’s a more serious problem with the gas line infrastructure in your home. Shut off the gas to your home at the main house-side valve and contact your gas company immediately. Your utility company will inform you of the next steps for gas repair.

Other unusual smells can signal the need for service as well. Acrid odors or the persistent smell of something burning could mean your stove or oven needs to be cleaned, or an internal wire or other part needs to be replaced.

Unreliable ignition is another clear sign that gas oven or gas stove service is necessary. If you can smell gas but can’t spark a flame on any burner, your igniter as failed. Resist the impulse to light the burner with a match or lighter. This can be dangerous if you don’t understand the scope of the problem, and it’s only putting off the inevitable repairs.

An extinguished pilot light is another possibility, but newer gas ovens and stoves tend to use an electrical means of ignition. Modern appliances, in other words, are unlikely to have pilot lights.

The heat control on your oven or stove should be relatively predictable. Pay attention to an oven that seems to take longer and longer to preheat, or a stove that you need to crank higher to get the same amount of heat that you were accustomed to generating at a lower setting on the knob. Similarly, have a professional inspect or repair your gas oven if the appliance is getting too hot for the temperature you have set it to. These are all signs of a faulty thermostat, heating mechanism, or other internal component.

Think of the flame on your gas stove as an indicator light. A clean, well-maintained stove should generate a blue flame. A red, orange, or yellow flame could suggest the flame is not burning hot enough. There could also be a buildup of material on the burner or somewhere within the appliance.

Requirements vary by location, but technicians generally need to be licensed and certified to work on gas appliances. Plumbers, repair specialists, and other tradespeople can receive authorization from regulators.

An improperly serviced gas appliance can pose a significant danger. If your appliance develops a problem, take care to do more than a cursory internet search, such as “gas repairs near me.” You’ll need to do your due diligence and find a licensed professional.

You can treat the warning signs outlined above as a gas appliance services checklist. Periodically check for odors, noises, faulty burners, temperature irregularities, and off flame colors. If you notice anything amiss, a home warranty can facilitate the repair of your appliance.

Liberty Home Guard policies cover all mechanical parts of ovens, stoves, cooktops, and ranges. If anything breaks down, all you need to do is submit a service claim. We’ll handle the rest.

The flame of a gas range burner should be steady and slightly rounded, with a light-blue tip. To adjust the flame, slide the air shutter mixer plate open or closed.

The flame of gas range burners should be steady and slightly rounded, with a light-blue tip. The flame should be quiet and should respond to adjustments made at the control knobs. Most burner troubles can be quickly solved by adjusting the air shutter mixer plate, which is located at the end of the burner tube near the knob controls. Turn a small screw on the plate, slide the plate open or closed, and tighten the setscrew.

One pilot light usually serves all the top burners of a gas range. Some ranges have two pilot lights, one for each side of the range. A correctly adjusted pilot flame is steady and blue, between 1/4 and 1/2 inch high. If the flame goes out repeatedly, or if it"s yellow at the tip, it"s getting too little air. If there"s a space between the flame and the pilot feed tube, it"s getting too much air. To correct either condition, turn the pilot adjustment screw on the gas line slightly, as directed by the manufacturer of the range.

Most newer gas ranges and ovens don"t have pilot lights. Instead, the gas is ignited by an electric ignition system. In this type of system, an element becomes hot and glows like the filament in a lightbulb when an electric current passes through it. The heat from the filament lights the gas. As a rule, these ignition systems are sealed and cannot be repaired or adjusted. When an electric ignition device fails, don"t try to fix it. Call a professional service person for replacement.

If the flame is set too low, adjust it. Next to the pilot, locate a small boxlike unit with a couple of screws in it. This is the ignition unit. The ignition unit could also be located below the pilot; follow the gas line down until you locate it. Turn one of the screws on the ignition. Experiment, turning the screws a little at a time, until the flame is adjusted properly. It should not be as high as the top pilot flame; leave it as low as possible. On some oven pilots, turn the control to the OFF position and light the pilot; then turn the oven dial to the BROIL position. The pilot will heat the controls to the ignition switch.

On some ranges, there is an automatic shutoff valve located in the pilot assembly that shuts off the gas to the burner any time the pilot and the burner are both off. If this unit malfunctions, don"t try to fix it yourself; you should call a professional service person for repair or replacement.An electrically operated shutoff valve used on some gas ranges has two facing valves, an electromagnet, and a manually activated reset button. The thermocouple fitting is next to the pilot valve, as in most burner systems. A small amount of electricity holds the facing valves apart. If the pilot light goes out, no electricity is generated, and the valve closes to turn the gas off. On this type of system, relight the pilot by depressing the reset button and holding a match to the pilot. It should take about a minute to light this pilot. If you aren"t able to relight this system, call a professional service person.Electric ovens and ranges are growing in popularity, probably because most repairs involve simply replacing a worn or faulty part. Learn more about how to provide routine maintenance for an electric range in the next section.

There are two types of self-cleaning ovens, pyrolytic and catalytic. Pyrolytic ovens use very high heat -- usually 1,000 degrees Farenheit -- to incinerate food on the oven"s surface, leaving only a fine ash. The smoke produced by the burning is vented from the oven. When the cleaning process is complete, the fine ash left in the oven can be wiped off the surface.

Catalytic self-cleaning ovens are coated with a special finish the allows most dirt to burn away at normal cooking temperatures. With these ovens, major food spills and spatters must be cleaned away immediately or the special finish will not work.

Most problems with pyrolytic ovens occur because procedures are not properly carried out. In most cases, the oven heat selector must be set to the CLEAN position, and the oven door must be firmly closed and sometimes latched. When the oven reaches a predetermined temperature -- about 600 degrees Farenheit -- the door automatically locks shut so that it can"t be opened during the cleaning cycle.

If you"ve followed the correct procedures for using a self-cleaning oven, but the oven is not coming clean, call a professional service person. Before you call, though, make these basic checks:

Be sure to allow the prescribed amount of time for the oven to clean itself. If the oven is only partially cleaned, more cleaning time may be required.

Gas ovens are not difficult to operate. Once you have turned the temperature knob to the desired setting, all you have to do is wait a few minutes for it to pre-heat before sliding your dish into the oven. But if your meal is left uncooked even after your cooking time has expired, there could be an issue with the oven’s heating mechanism and you’ll want to address it.

Do not attempt to identify the problem yourself if you smell gas while the oven is shut off. If that is the case, contact a professional repair service immediately. With that said, there are a few troubleshooting methods to consider should your gas oven fail to heat.

First, test the burners on the stovetop. If no flame is produced, check the supply valve, unless your stove operates on LP gas and the tank level needs to be checked instead.

Next, open the door of the oven’s broiler section and check the oven’s inner workings. The oven burner and ignition system are located in the upper portion of the broiler chamber. Take a moment to inspect the burner tube for obstructions or holes from corrosion or overheating.

For pilot ignition systems – or if the pilot light is functioning – turn on the oven and watch the burner tube. If the burner tube creates no flame or a weak flame and fails to heat, the safety valve could be faulty.

For best practices, refer to your owner’s manual for exact instructions on how to inspect the oven. If there are concerns at all for your safety, your best option is to call a professional.