wire rope clips and thimbles pricelist

We have invested millions of dollars in our own test labs and factories, so our tools will go toe-to-toe with the top professional brands. And we can sell them for a fraction of the price because we cut out the middleman and pass the savings on to you. It"s just that simple!

Wire rope clips are widely used for making end terminations. Clips are available in two basic designs; the U-Bolt and fist grip. The efficiency of both types is the same.

When using U-Bolt clips, extreme care must be exercised to make certain that they are attached correctly; Incorrect installation can reduce the working load limit by 40%. Below are general guidelines for installing wire rope clips.

The saddle shall be placed on the live end of the wire rope, with the U-bolt on the dead-end side—Remember the well-known saying: “Never saddle a dead horse.” Use at least two or three wire rope clips to secure the ends properly to the length of the rope, and tighten nuts evenly one by one until reaching the recommended torque.

Step 1. Turn back a specified amount of rope from the thimble or loop. The first clip must be placed one bridge width from the turned back rope tailor dead end of the rope, Apply U-Bolt over dead end of wire rope – live end rests in the saddle (Never saddle a dead horse!) Tighten nuts evenly, alternate from one nut to the other until reaching the recommended torque.

Step 2. When more than two clips are required, apply the second clip as near the loop or thimble as possible, tighten the nuts firmly but not yet to the specified torque.

Step 3. When three or more clips are required, space additional clips equally between the first two – take up rope slack – tighten nuts on each U-Bolt evenly, alternating from one nut to the other until reaching recommended torque.

Step 4. Apply the first load to test the assembly. This load should be of equal or greater – weight than loads expected in use. Next, check and retighten nuts to recommended torque.

In accordance with good rigging and maintenance practices, the wire rope end termination should be inspected periodically for wear, abuse, and general adequacy. Periodically re-tightening of the nuts must be done at 10.000 cycles (heavy usage), 20.000 e.g. every 3 months, 6 months, annually.

Malleable clips are to be used for making eye termination assemblies only with the right regular lay wire rope and only for light-duty uses with small applied loads, such as handrails, fencing, guard rails, etc.

If you have any wire rope clips questions, you can contact us by email at info@hilifting.com. We will be glad to share with you more useful information.

We have ½" Galvanized Super Swaged Cable. For a smoother, quieter and faster zip line ride. This 6X26 Cable boast a 35,210 pound tensile strength. It is made by swaging 9/16" Wire Rope down to

For Larger Orders please call (800)845-5692 and we will be happy to assist you. If you require a length that is not shown on the drop-down list below please call or Contact Us.

A must when connecting cable to nut eye bolts or ovaleye bolts. Keeps the cable from flattening around the eye causing the cable to weaken. Also used in eyespliced ropes. *When using a guy thimble

Usually only used on cable or wire rope. Match the thimble size to your cable diameter. We offer an open pattern of the 3/8" which is gapped to fit onto our nut eye bolts and ovaleye bolts.

Wire Rope Clips are used to secure the end of wire rope when forming a loop; i.e., for wire rope turn-back. Clips are available in two configurations: mid-grip (double saddle) and single

Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 1/8"-7/8" sizes, and 90% for sizes 1" through 3-1/2".

Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these wire rope clips meet other

spinning even after repeated use and re-torqueing. It has precise threading on the nut and bolt to ensure tight alignment. This design also allows for full arc wrench swing, making installation and

Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 3/16"-7/8", and 90% for sizes 1" through 1-1/2".

Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these wire rope clips meet other

Fist Grip wire rope clips meet or exceed the performance requirements of Federal Specification FF-C-450 Type III, Class 1, except for those provisions required of the contractor. For additional

Also known as a double grip clip. The design allows the installer to turn their wrench freely since the other nut is on the opposite side. More important, when these clips are removed from your

Apply the first clip one base width from the dead end of the wire rope. The base or saddle should bear on the line end of the rope - U-bolt on the short end. Tighten nuts firmly.

Attach balance of clips spaced equally between first two clips. Tighten all nuts completely. Apply initial load - inspect nuts and retighten. Inspect all clips periodically.

To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzed reviews to verify trustworthiness.

Founded in 1969 under the motto of “Always Thinking Productivity”, Cutting Tools Inc.is the premier distributor for the Automotive, Aerospace, Defense, Energy, Firearms and Medical manufacturing industries. To get in touch, contact us at cs@cuttingtoolsinc.com

Founded in 1969 under the motto of “Always Thinking Productivity”, Cutting Tools Inc.is the premier distributor for the Automotive, Aerospace, Defense, Energy, Firearms and Medical manufacturing industries. To get in touch, contact us at cs@cuttingtoolsinc.com

This is the price (excluding shipping and handling fees) a seller has provided at which the same item, or one that is nearly identical to it, is being offered for sale or has been offered for sale in the recent past. The price may be the seller"s own price elsewhere or another seller"s price. The "off" amount and percentage simply signifies the calculated difference between the seller-provided price for the item elsewhere and the seller"s price on eBay. If you have any questions related to the pricing and/or discount offered in a particular listing, please contact the seller for that listing.

We are a manufacturer and distributor of industrial snaps and all types of connecting products and accessories meeting global quality standards at highly competitive prices. Our shortest lead time, end-to-end customer lifecycle management process and an expanding reseller network make Baron the go-to partner for businesses in this industry to achieve accelerated business growth.