wire rope for shade sails manufacturer

Yes. Wire rope is an essential part of our shade sails. Without a wire rope around the perimeter, tension applied at each attachment point is not distributed evenly in the sail, creating areas of concentrated stress around the corners. This causes the center to sag and increases the risk of tearing at the corners.

When a wire rope is used, the pulling force from the attachment hardware is transferred to the wire rope, rather than directly to the fabric. That force is then distributed throughout the perimeter of the sail, where the wire rope runs through a pocket. As the curved edges of the sail are pulled taut, the wire rope and fabric attempt to straighten out, which pulls the center of the sail up and fights sagging.

Wire rope which is an attachment accessory which helps in the installation of the sun shade sail.The small rope kit features wire rope clips and wire rope to assist in the installation of Shade Sails for that classic design you desire in your backyard, patio, or any outdoor living space.

DISCLAIMER (Read carefully) The following installation suggestions and helpful hints for shade sails are offered as a courtesy to mail order purchasers and to facilitate accurate ordering of the product. Shade Sails does not and cannot know the specific intentions of purchaser stress factors, variables for the area such as soil, wind condition and exposure, existing structure strength, local access codes, etc. The following is offered only as a highly generalized summary of installation methods used successfully by Shade Sails in the past. Shade Sails makes no extension of warranty by these general guidelines and disclaims any responsibility for the installation, design of installation, engineering requirements, code compliance or any other installation related matter. Shade Sails offers these services on an individual contract basis and purchaser has elected to purchase the ready-made sail only as a more economical alternative.

Check with your local building Dept. Some installations require a building permit. We are not responsible for obtaining permits or for engineering your installation. The following information is meant as a guideline and not intended to replace the services of a structural or civil engineer. Selecting the position: Before you commence installation it is very important that you consider the most suitable location for your shade sail(s) taking into account the following:  Size of the shade sail(s). Strength of existing structures intended to be anchor points. Ability to insert fixing posts.  Location of barbecues or Sun direction etc. Sails should be separated by about 18″when layered to avoid chafe. Watch out for tree branches that may also chafe the sails.

Unlike custom made sails that are made to fit, you have to supply supporting hardware that is in line with the corners of the sail and provides enough room to add attaching hardware or rope. It is best to make the structural element’s foot print 18″  larger than the sail’s dimension so that variations in the sail’s size is not a problem and there is enough space to add rope, links of chain, turnbuckle, shackles etc.  Do not add more than 24″ on more than one corner..(One corner per sail may be extended up to 30’ but only a single corner) If you extend 2 or more corners with cable, rope or chain the membrane will move excessively in a wind and the resulting shock loads may significantly reduce the life of the sail.. Long leaders on multiple corners will void any warranty.

To help you visualize the Sails, you can also use string stretched between your planned attachment points. The first step is to measure.  Then make a scale drawing of the area you want shaded. 1/4 (or 1/8) inch = 1 foot. Then cut out scale drawings of the ready-made shade sails. Rotate them around to get ideas for the lay-out. Imagine a straight line from the center of the shade sail through the corner ring, that is where you need to put the attachment point. The fabric is a knit and most of the water sheds off the lowest point, but it is not waterproof.  Remember the sails do not have straight lines at the edges; they are constructed with a gentle curve that deflects about 10% over the length of each edge. We have found the best looking installations have bold changes in height from one corner to the next, and that overlapping sails or multiple sails give a more interesting look.

The attachment points should be installed first. Therefore, install your posts with eye-nuts, and to the house, tree or whatever you have chosen to support them, add eye bolts, pad-eyes or straps. Remember, there can be substantial wind loads. (From 5.5 to 15 lb. Per square foot of sail). These loads are divided between the corners, but it is important that what they attach to be adequate. For the posts, we usually use 4″ schedule 40 steel pipe (galvanized) or temporary power poles (treated) that are 6″ or larger. (

The sails have a stainless steel ring at each corner that must be attached to your fixing point. This can be done in a variety of ways; the best method for the “do it yourselfer” is to tie them on with a length of low stretch Dacron rope. This gives a lot of adjustability and is very strong and inexpensive. For a more high tech look you can use stainless steel “D” shackles and turnbuckles or even chain.

Do not leave sails up in snow prone locations during winter months and unless your installation has been engineered for permanent use they should be taken down

rope or chain the Shade Sail will move excessively in a wind and the resulting shock loads may significantly reduce the life of the sail.. Long leaders on multiple corners will void any warranty.

We use Tenara thread on all of our products. Tenara is guaranteed to last as long as the shade cloth. In our experience, Tenara far outlasts standard awning thread.

For a limited time only - 1st August 2021 until 30th September 2021 - we"re offering exclusive discounts on our shade sail product range to trade customers and businesses who download our catalogue.

Check your DNS Settings. A 523 error means that Cloudflare could not reach your host web server. The most common cause is that your DNS settings are incorrect. Please contact your hosting provider to confirm your origin IP and then make sure the correct IP is listed for your A record in your Cloudflare DNS Settings page. Additional troubleshooting information here.

See your design in a 3D model! This allows for clients to better understand how their shade sail or shade structure will look and feel before seeing the final product.

We use high quality shade sail hardware. Most of the shade sails come with stainless steel hardware and full perimeter wire rope. Some larger projects require larger galvanized hardware.

All of our shade sails and shade structures are fully custom from design to install. We have the ability to design our sails in all shapes and sizes. Controlling the the arch depth and ability to even curve the shade around corners.

Pictured here, we can integrate a kiss spot in the shade sail design. A “kissing spot” is where two separate shades have a connection point between two sides. This helps minimize the space between curves of fabric and creates a nice dynamic look and shade pattern.

Our Shade Sails offer terrific shade for both residential or commercial property landscapes, creating the perfect, breezy oasis when the sun just gets too hot. You’ll love that our Shade Sails, manufactured from top-quality, high-tensioned fabric, are precisely shaped to the exact dimensions of the area you’d like to protect.

New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller"s listing for full details.See all condition definitionsopens in a new window or tab

Note: The fabric colors represented on the website may differ slightly from the actual product, and different monitors may cause colors to vary slightly. We recommend customers contact us to order a color swatch before buying if needed. Viewer"s discretion is advised.

No liability accepted whatsoever in the event of failure of any DIY Shade Sail / Project purchased from diyshadesails.net.au. We are unable to offer design and building advice. Please note, our service extends only to the manufacture of the Shade Sail. Consult with a Building Professional before first embarking on a DIY project. Consult with your Local Regulatory Authority as Planning Laws vary.