piggyback hydraulic pump price
The SPD2 series of pumps are special SP-25A series pumps with through shafts. The through shafts have 9 tooth internal splines at the rear and the pump’s rear cover has an integral SAE A-2 bolt mount pad. For double pump operation, a standard SAE A-2 boltsplined shaft pump can be directly mounted on the rear on the SPD2. Typical performance of the pump is the same as indicated for the SP-25A series pump.
Pump is open back type to use w/piggy-back pump(THIS TYPE HAS 2 OUTLET HOLES, NOT PICTURED), 17 GPM rating, max PSI of 2250. Not for use in 12 GPM systems. If system is 12 GPM, use 1949296C1.
The service life of various hydraulic valves in the hydraulic support is very low. The way and solution for solving the problem abroad is to improve the filtration precision of the system and improve...
In this paper, we will analyze the last cause of the failure of the hydraulic valve in the future: cavitation. In this paper, we will analyze the last cause of the failure of the hydraulic valve in...
BWCB insulation gear pump motor high temperature reasons and countermeasures analysis 1, cause analysis (1) motor power, large operating current, large heat. (2) The fan speed is low, the wind...
Gear oil pumps are mainly used in the transfer, oil pressurization, fuel injection, etc. of oil media in chemical, petroleum, mining, metallurgy, power station and other industries, as well as in the...
The basic form ofhydraulic tandem gear pumpis that two gears of the same size engage and rotate each other in a closely matched shell. The inner part of the shell is similar to the "8" shape. Two gears are installed inside, and the outer diameter and sides of the gear are closely matched with the shell. Material from the extruder enters into the middle of the two gears at the suction port and fills the space. It moves along the shell with the rotation of the teeth, and finally discharges when the two teeth engage.
In terminology, tandem gear pump is also called positive displacement device, that is, like a piston in a cylinder, when one tooth enters the fluid space of another tooth, because the liquid is incompressible, so the liquid and the tooth can not occupy the same space at the same time, so the liquid is mechanically squeezed out. Because of the continuous meshing of teeth, this phenomenon occurs continuously, thus providing a continuous exclusion quantity at the outlet of the pump. Every turn of the pump, the discharge quantity is the same. With the uninterrupted rotation of the drive shaft, the pump also discharges fluid uninterruptedly. The flow rate of the tandem gear pump is directly related to the speed of the pump.
In fact, there is a small amount of fluid loss in the pump, because these fluids are used to lubricate both sides of bearings and gears, and the pump body is never able to cooperate without clearance, so the fluid can not be discharged 100% from the outlet, so a small amount of fluid loss is inevitable, which makes the operation efficiency of the pump can not reach 100%. However, the external gear pump can still run well, and for most extruded materials, the efficiency can still reach 93%-98%.
The speed of a tandem gear pump is actually limited, which mainly depends on the process fluid. If the oil is transferred, the pump can rotate at a very high speed. But when the fluid is a high viscosity polymer melt, the limit will be greatly increased. It is very important to push the high viscous fluid into the two teeth space on the side of the suction port. If the space is not filled up, the pump can not discharge the accurate flow, so the PV value is another limiting factor, and it is also a process variable. Due to these limitations, gear pump manufacturer will provide a range of products, namely, different specifications and displacement. These pumps will be combined with specific application process to optimize system capacity and price.
Depending on your requirement and type of industry, you can buy the best quality and advanced tandem gear pump online at competitive prices and get a guide to their installation and use.
Do you need Geartek hydraulic pump repair, rebuild, or replacement? We offer Geartek pump repair and rebuilds. If you need a free estimate for any Geartek pump, get in touch with us today to find out how much it will cost for repairs.
We provide fast, reliable hydraulic pump repair service on all Geartek models. We are guarantee all repair work will be done with genuine OEM parts, so you know that you aren’t getting gray market or counterfeit parts.
Our team of skilled technicians will give your pump the attention it needs, and put it through our detailed inspection and repair process. Once the pump has been reassembled, we’ll test it thoroughly with our state-of-the-art-test equipment.
When you get your pump back, it will meet or exceed factory specs. Once you work with us, we think that you will keep coming back to us for all of your Geartek hydraulic repair needs.
If you don’t see your model number listed below, don’t hesitate to call or contact us. We service just about every model of pump that is available from Geartek and other manufacturers.
When you are on the job and under a deadline and equipment fails, you need fast, reliable repair. We can send in our field technicians to get your Geartek pump back up and running as soon as possible. Our reliable, experienced team can perform diagnostic services and minor repairs for equipment and machinery used in many industries. Our team can travel throughout the United States and many international locations, including North America and South America.
If repairs cannot be made on-site to your Geartek pump, you can ship it to our facility. If you’re close enough, you can drop it off. We know how important it is to get your operations back up and running. So you can trust us to get your pump repaired and back to you as fast as possible, and working properly.
Geartek hydraulic pumps combine the reliable, economic features of external gear design with modern engineering and materials to produce true pressure ratings up to 4000 psi. Although Geartek is a major supplier to OEM’s, the company is not too big to supply custom-built, small run, or out-of-production-pumps.
Don’t see your Geartek hydraulic pump model number? Not a problem. Call 800-800-6971 or send us an email. Chances are we’ve worked on it before and have parts for it, even if it’s not listed on our website.
We provide hydraulic components & repair services for industrial applications like paper mills, saw mills, steel mills, recycling plants, oil & gas applications and mobile applications, including construction, utility, mining, agricultural and marine equipment. This includes hydraulic pumps, motors, valves, servo/prop valves, PTOs, cylinders & parts.