plunger hydraulic pump factory

Piston pumps can be used for low viscosity and medium-flow media (in the range of 80 m³/h). Additionally, pumping solid particles is impossible with this type of equipment because the pump can ensure proper operation only if the seal between the cylinder and the piston is perfect.

For high-pressure uses, you can opt for a plunger pump, they differ from piston pumps in that the seal does not move with the piston, it is fixed and therefore able to withstand...

... is a plunger metering pump with the option of adjusting the pump capacity in 0.2% increments. It offers a wide range of power end versions, such as three-phase or 1-phase AC motors, even ...

The plunger metering pump Makro/ 5 (M5ka) together with the Makro/ 5 hydraulic diaphragm and diaphragm metering pumps, form a range of drive mechanisms ...

... consumption of many other pumps on the market. Plus, the Python’s extreme duty plungers, seals and timing valve are designed for years of operation before replacement.

... heavy duty frac pump designed to operate at higher pressures for longer periods of time. Its compact design and 11” stroke results in less fatigue cycles and extended consumable life. With a legacy of ...

... pressure of 4,136 bar, KMT WATERJET SYSTEMS offers the STREAMLINE SL-VI STD high pressure pump as a lower priced alternative still featuring KMT"s advanced pump technology. The STD models can be operated ...

The NEOLINE pump has been developed with the aim of creating a robust, easy to operate pump. It is driven by a 40 hp (29 kW) three-phase motor which is equipped with vibration isolation pads ...

With operating pressures of up to 1,000 bar, the Y-series pumps are ideally suited to a wide variety of cleaning work, e.g. in the chemical industry, oil and gas industries as well as in the area of ship cleaning. Due ...

... high-pressure plunger pumps of the 2-series with operating pressures up to 750 bar and volumetric flow rates up to around 230 l/min are ideal for cleaning pipes and tube bundles, containers and containers. ...

... Abrasive Resistant Pump) high-pressure plunger pump series was developed specially for the conveyance of water contaminated with grainy or fibrous solids. The ARP high-pressure pumps ...

The “V” Series pump is a range of compact, self-contained, pneumatic metering pumps suitable for injecting a wide variety of chemicals that range from 0.07 gph to 9 gph (0.27 lph to 34 lph) and pressures ...

Three-es manufactures pumping sets with various flow and pressure characteristics, plug&play and optimised for any washing system. Each pumping unit is assembled using only high quality components.

... to simple hand operated plunger pumps for pressure testing, large three, four or five plunger pumps of various designs are available with specific advantages for specific ...

... robust dimensioning of the pump drives, the determination of optimum clearance in the pump element and the application-oriented selection of high-strength steels with special heat treatment processes. ...

Drilling pump is also called mud pump, which transport high pressure, high specific gravity, high sand concentration drilling fluid to bottom of hole. Drilling fluid is used to cool bit, wash out bottom ...

These models are equipped with a hydraulic motor-driven, triplex plunger pump; and include an unloader, gauge, and quick disconnect. Select models ...

The popularity of hydraulic piston pumps stems from their ability to maximize energy use and productivity. Even a hydraulic hand pump, which is powered by a foot or hand pedal, can convert as little as 4.5 pounds of force into 100 pounds of load-moving force. Electric hydraulic pumps can reach pressure ranges up to 4,000 PSI. As capacities show such variability, the intended use of a pump should be carefully considered. Several other variables should also be taken into account.

Task-specific power sources, operating speeds, maximum fluid flows and pump weights are widely available in standard and custom configurations. Measurements such as diameter, rod extension length, height and width should also be considered, especially when a hydraulic piston pump is to be fitted to a pre-existing hydraulic system.There are two basic variations of hydraulic piston pumps: axial and radial pistons. The essential difference between the two is the placement of the pistons within the hydraulic cylinder and the directionality of the movement. Axial pistons run parallel to the cylinder, while radial pistons are perpendicular to an inner column running through the cylinder. The latter provides a rotary movement. Axial pistons provide linear motion and are more popular in heavy machinery contexts.

Both can be single action or double action pumps. Despite the differing piston placements, both systems function in a similar fashion. Hydraulic fluids, usually oil or water composites, are housed in a reservoir connected to the main cylinder by tubes or hoses. The cylinder houses the pistons as well as one or more intake check valve and an equal number of discharge check valves. When the piston is withdrawn it creates a vacuum, and the liquid solution is pulled into the cylinder.

The piston is then returned to its original position and the intake valve is sealed. This creates pressure within the enclosed space and compresses the fluids. The plunger-like action is repeated until enough pressure is accumulated to force the hydraulic fluids out through the discharge valve. This creates the energy needed to work the attached machinery and move the intended load.

Wepuko PAHNKE triplex plunger pumps are high-pressure horizontal plunger pumps in series. They can be designed for almost any pumpable medium. Three plungers are a good compromise between low pulsation, cost-efficient and maintenance-friendly design.

Our plunger pumps consist of two main components: the damped-mounted and lubricated drive and the liquid part, consisting of three cylinders and the valve body. The housing of the power unit is in one piece in these high-performance machines, a compact and inexpensive solution. Built-in pressure or wiper lubrication automatically supplies the engine parts with lubricating oil.

Features a hybrid drive system that combines the benefits of hydraulics with the controllability of an AC servo motor and inverter motor to satisfy a broad range of specifications with a small volume pump. Users will find energy savings in fields such as industrial machinery and machine tools.

Total weight 3.3kg. The weight of the device on ankle part where the exercise load is big is reduced to 0.97kg by wearing the power supply on the waist. 65Nm torque is generated by Takako"s standard 0.4cc pump.

Piston pumps are typically much more complicated and are often available in wither fixed or, commonly, variable displacement configurations and with pressure compensation. These are big words that mean that piston pumps can usually adapt to the system pressure, providing maximum efficiency and flexibility. They are often used in “closed center” systems where the pump displacement varies to meet the needs of the work being done. Piston pumps use a “swashplate” to move the pistons and the angle of the swashplate & bore of the pistons determines the displacement. Pressure compensation regulates outputs in response to variations in the system. Piston pumps are typically the most efficient type of hydraulic pumps.