power up / power down hydraulic pump wiring factory

We"ve taken the time to coat the male poppet end with Titanium Nitride (Ti-Ni). Persistent coupling and decoupling along with inevitable particulates getting between the couplers leads to scratches and abrasions. These inconsistencies will eventually...

Our couplers are machined out of carbon steel and plated with Zinc Nickel (Zn-Ni), which offers corrosion resistance, as well as an extra layer against normal wear and tear. Each coupler is pressure tested with hydraulic oil right off the factory line. ...

Our couplers are machined out of carbon steel and plated with Zinc Nickel (Zn-Ni), which offers corrosion resistance, as well as an extra layer against normal wear and tear. Each coupler is pressure tested with hydraulic oil right off the factory line. ...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

TEMCo Industrial"s hydraulic cylinders come with an ISO 14540 coupler, which means you"re compatible with a large majority of other products out on the market. Don"t deal with the headache of mismatched fittings and confusing coupler specifications -...

BRI-MAR Remote with Cord is for the Power Up / Power Down function commonly found on hydraulic power units for dump bodies. Wiring harness has four wires come out the end: Black with ring terminal and white, red, and green, with a U shaped terminal.

2.Target will not take responsibility for wrong installation and wrong application. Do not exceed the rated limits of the power unit or use the power unit for applications beyond its design capacity.

To avoid personal injury or equipment damage, all power unit repair, maintenance and service must only be performed by authorized and properly trained personnel.

4.Always disconnect the battery cable before attempting any repair. Do not inspect or clean the hydraulic pump or hydraulic tool while the hydraulic power source is engaged.

Disconnect both hydraulic hoses before attempting to clean or inspect the pump or hydraulic tool. Accidental engagement of the power unit can cause serious injury.

Over torque on valves could cause the cage of valve assembly to distort. Distortion could cause valve to not properly open and/or close, which could simulate contamination issues.

Failure to oil valves will cause O-rings to spin on valve assembly which could cause to O-ring slice length wise, cut or tear. Use Hydraulic fluid to lubricate O-rings, Do Not use any type of grease or motor oil. Grease or motor oil could cause valve failure when the hydraulic fluid mixes with foreign substance and gum up valves.

The Hydraulic Circuit and Wiring Diagram will help you know the function of hydraulic power pack and help you to troubleshooting in your hydraulic systems.

The hydraulic oil fluid will comes to into hydraulic gear pump  through the filter, suction pipe,  and then goes into the “P” port on central manifold ,inside of hydraulic reservoir tanks and  delivered to the Outlet port “P’  through check valve and normally closed (NC type) solenoid valve.

The needle valve (throttle) is used to control the speed of cylinder down, if the needle valve too tight cylinder down speed will be slow, if the needle valve get loose the speed will get fast. But be careful, not lose too much, or the needle valve will leak and cause much noise and danger, the Cylinder will also coming down unstable. (So it is better to let the Target Hydraulics Engineers or Sales know your cylinder speed and not touch the needle valve by yourself.)

Hydraulic oil can’t be higher than ISO 4404406/14. Hydraulic oil should be filtered by 10-30um filter. Suggestion: Oil viscosity – Summer HM32/46# or transmission oil – Winter HM22 or transmission oil.

check on valve solenoid, a manual override turn counter clockwise will rise down immediately. It Have to be closed for power up.If Solenoid Valves without manual override then clean this solenoid valve in manifold block part.

L’huile hydraulique doit être filtrée à 30 micron. Suggestion: Viscosité de l’huile  – Été: 32/46ou huile à transmission           – Hiver: 22 ou huile à transmission

Our Engineers use 3D and 2D software for hydraulic manifold blocks and hydraulic power unit system design. You can have free design help with your new inquiry.