pto hydraulic pump for vacuum planter for sale

It mounts easily to any planter and, depending which pump size is purchased, will provide an extra 12 gpm to 40 gpm as well as 4 to 6 additional ports.

Many producers wanting to upgrade or upsize their air seeders discover they are lacking hydraulic capacity on their current tractor, and don’t have room in their machinery budget to upgrade their tractor.

One solution is the Command HydraBoost PTO-driven auxiliary hydraulic system, these can operate a portion of the hydraulic flow requirement, allowing producers to continue using their favourite tractor! These units come in several sizes, the larger sizes - 24gpm, 32 gpm & 40 gpm are used in combination with air seeders.

PTO-driven hydraulic vacuum pumpThis attachment allows using the vacuum seed meter system pump with tractors having an open-center hydraulic system and/or a 540-rpm or 1000-rpm PTO.

Flat seed disks such as edible bean and sweet corn require high levels of vacuum. These disks require a dual vacuum motor configuration on planters over 8 rows. The 1000-rpm PTO pump is not adequate for this application.

PTO-driven hydraulic vacuum pumpA PTO-driven hydraulic pump allows operators to use the vacuum seed meter system with open-center hydraulic tractors and/or a 540 rpm or 1000 rpm PTO. The 540 rpm PTO system is compatible with 4Row through 9Row planters and provides 3.9 gpm at 80 percent of rated speed. The 1000 rpm PTO system is compatible with 4Row through 15Row planters and provides 5.0 gpm at 80 percent of rated speed. Both the 540 and 1000 rpm PTO pumps are for single vacuum motors only and inadequate for dual vacuum motors systems.

Flat seed disks such as edible bean and sweet corn require higher levels of vacuum. These disks require a dual vacuum motor configuration on planters over 8 rows. Neither the 540 or 1000 rpm PTO pump is adequate for flat seed disk operation.

9000 Codes include an oil cooler, except with 4-row planters with 540 rpm pump. When ordering PTO pump as a bundle, you must also order the oil cooler bundle, except with the 540 rpm PTO pump for 4-row applications.

I am wanting to run my two vacuum motors on 1780 planter off of a pto pump. I was considering a hydraboost system until I got the price for their unit. I am now thinking I should just piece the system together myself to save some money. I seen where the two motors are probably going to require around 4-5 gal/min each so I don"t need a very big system. I was looking at a prince pto pump but would like to see if others have made their own system, what they all used and how it was plumbed. I currently use my 7800 for all hydraulic functions with a case drain, it has the two dials to regulate vacuum. I am just trying to figure out how to incorporate these in the new system to allow fine tuning of vacuum. Also is it better to use 540 or 1000 rpm pump? Thanks in advance.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

�����HydraBoost is a closed center, pressure compensating system powered by a pto,� says Dan Symington, Command Hydraulics. �We can produce the higher pressure needed for down pressure and for other precision planting equipment, as well as for vacuum fans and more.�

����The company suggests that HydraBoost works with every tractor/planter combination on the market. It is available in multiple sizes, from 12 gpm to 40 gpm, and can be equipped with either 4 or 6 additional ports. Reservoir capacity ranges from 15 to 25 gal., depending on pump size. The kit also includes Command Hydraulics� PumpDoctor, designed initially for use with Case IH and Kinze planters.

�����PumpDoctor is an integral part of HydraBoost,� says Symington. �We also sell it by itself for use with other pto-powered hydraulic pumps. Anytime you put a pump directly on the pto, you tend to get vibration. Our double chain connection PumpDoctor cushions it.�

����The PumpDoctor is a support bracket that secures any pto pump directly to any tractor frame via a mounting plate. Without such a bracket, the pump hangs on the pto shaft. The weight causes excess vibration, shaft strain and warping or breakage. The PumpDoctor is available in 3 models for 16, 18 and 12-tooth sprockets.

����The tractor mounting plate is designed to match the exact bolt pattern for specific tractor models, ensuring a secure and tight fit. The PumpDoctor kit also includes sprockets, chain and hardware for mounting.

����Contact: FARM SHOW Followup, Command Hydraulics, 8095 215th St. W., Lakeville, Minn. 55044 (ph 952 890-6800; toll free 800 778-6200; sales@commandhydraulics.com; www.commandhydraulics.com).

Slick Way To Add Extra Hydraulics MISCELLANEOUS EQUIPMENT Pumps You can get more hydraulic power from your existing tractor with HydraBoost from Command Hydraulics Designed to meet the needs of new planters and other hydraulic power hogs HydraBoost is a self-contained auxiliary hydraulic supply package It can eliminate the need to trade up tractors to run a planter that needs more hydraulic power �HydraBoost is a closed center pressure compensating system powered by a pto � says Dan Symington Command Hydraulics �We can produce the higher pressure needed for down pressure and for other precision planting equipment as well as for vacuum fans and more � The company suggests that HydraBoost works with every tractor/planter combination on the market It is available in multiple sizes from 12 gpm to 40 gpm and can be equipped with either 4 or 6 additional ports Reservoir capacity ranges from 15 to 25 gal depending on pump size The kit also includes Command Hydraulics� PumpDoctor designed initially for use with Case IH and Kinze planters �PumpDoctor is an integral part of HydraBoost � says Symington �We also sell it by itself for use with other pto-powered hydraulic pumps Anytime you put a pump directly on the pto you tend to get vibration Our double chain connection PumpDoctor cushions it � The PumpDoctor is a support bracket that secures any pto pump directly to any tractor frame via a mounting plate Without such a bracket the pump hangs on the pto shaft The weight causes excess vibration shaft strain and warping or breakage The PumpDoctor is available in 3 models for 16 18 and 12-tooth sprockets The tractor mounting plate is designed to match the exact bolt pattern for specific tractor models ensuring a secure and tight fit The PumpDoctor kit also includes sprockets chain and hardware for mounting HydraBoost ranges in price from $5 245 to $11 500 Pricing for the PumpDoctor is available from the company Contact: FARM SHOW Followup Command Hydraulics 8095 215th St W Lakeville Minn 55044 ph 952 890-6800; toll free 800 778-6200; sales@commandhydraulics com; www commandhydraulics com

Home » John Deere » PLANTER » 1760 - PLANTER » 1760 Wing-Fold (8-Row and 12-Row) Drawn Conservation Planter and 60 Seed Cart » VACUUM SYSTEMS » PTO HYDRAULIC PUMP WITH COOLER

PTO HYDRAULIC PUMP WITH COOLER - PLANTER John Deere 1760 - PLANTER - 1760 Wing-Fold (8-Row and 12-Row) Drawn Conservation Planter and 60 Seed Cart VACUUM SYSTEMS PTO HYDRAULIC PUMP WITH COOLER | 777parts

We sell new, used and rebuilt parts for construction equipment. Excavators, Bull Dozers, Wheel Loaders, Motor Graders, Scrapers, mini-excavator and more.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

You"d really need to get down to the flow/pressure specs needed for your planter and compare them to the IH planter"s you"re looking at robbing if you go that route. They"d need to be within the same range.

I guess the question I"d be asking or wondering about is why you wouldn"t just run it off the SCV"s on a new tractor if you"re doing that now. Most 1/2" valves flow about 16 GPM per pair. The Ford shouldn"t have any problem doing that if the planter is using most of it"s flow. The problem you get into on the open center Ford"s is when you try to choke them down and they have to dump a significant portion of their pump flow at pressure across the unloading valve...

You might also want to double check and see if the 7740 isn"t a CCLS tractor to start with... Many, if not most around here were. If it"s an "SLE" with the 16x16 transmission, or even a 24x24, it should be CCLS. A 12x12 or the 8x2 would be open center. Those are "SL" and "S" models. The "SLE" will have no problem doing what you want in running the planter on the SCV.

Another option I"d look at would be PTO driving the fan. The planter I use is set up like that and just geared to run the tractor at mid-speed on the PTO. Something to think about...

The MaxEmerge family of row-units have never seen a more versatile and efficient design until the MaxEmerge 5. The 5-family row-units improve productivity, increase uptime and lower the cost of ownership like never before.

The vacuum meter system gently pulls and holds individual seeds to the holes of the seed disk for population control and spacing accuracy, equaling better crop stands and profit. Vacuum seed meters can plant a wide variety of crops and seed types by simply changing seed disks and adjusting vacuum level. Vacuum seed meters are available for planters with MaxEmerge 5 row-units.

The MaxEmerge 5 meter shape has also been redesigned for better seed flow. The mini-hopper design allows the planter to successfully operate on side hills up to 14 degrees.

Both the MaxEmerge 5 vacuum meters are equipped with a heavy-duty hub spring and disk latching handle. The spring ensures the seed disk stays properly positioned when operating flat-style seed disks and higher vacuum levels. Proper seed disk positioning means repeatable seed singulation, time after time. The disk-latching handle is designed for easy operation and effortless seed disk changeover. The hub is also machined to tight tolerances to further ensure alignment of metering components.

The vacuum seed meter is capable of operating at faster planting speeds than mechanical meters. However, planting accuracy will be influenced by seedbed conditions and the operating characteristics of the seed meter. Rough seedbeds and fast planting speeds (above 8.9 km/h [5.5 mph]) typically deteriorate seed placement accuracies when using seed tube technology.

The chart illustrates the effect operating speed has on population when using the vacuum meter. The operating band (color area) illustrates how the vacuum meter performs in relation to the desired population (indicated by horizontal line). The width of the band is due to various sizes and shapes of seeds and planting rate variations.

When operating on slopes above 15 degrees, increased or decreased population may result. To minimize this effect, reduce speed and consider using a flat style seed disk with increased vacuum level.

The ProMAX 40 Flat Disk utilizes flat holes and a higher vacuum level to ensure every hole is populated with a seed. A double eliminator gently removes multiple seeds at each hole for precise population control. A knockout wheel makes certain that each hole is clear of any debris after the seed is released from the disk.

The unique cell disk design allows planting a variety of seed sizes without any additional parts or individual meter adjustments. Another advantage of cell-type seed disks is the lower vacuum requirement compared to flat-style seed disks. Lower vacuum levels mean less hydraulic demand from the tractor. Most planting conditions call for a flat disk, if you are limited in hydraulic capacity, cell disks are recommended.

For difficult to singulate seeds, a flat seed disk and double eliminator is a viable alternative to traditional cell-type seed disks. By design, a flat seed disk requires higher levels of vacuum than a cell-type disk because there is no pocket or cell to hold the seed. The higher vacuum level will pull more than one seed to the holes in the seed disk. The double eliminator is set to cover a portion of the hole in the seed disk and is the mechanism to knock multiple seeds away as the disk rotates.

NOTE: Due to small seed size and low planting populations, sugar beets can be planted with mini-hopper style meters by adding hopper extensions and not using the CCS tank. These hopper extensions can also be used for planting test plots.

There are significant changes to the MaxEmerge 5 Mini-Hopper. One update is the straight feed from the Central Commodity System (CCS™) hose to the mini-hopper to ensure a continuous free flow of seeds. This design change reduces the potential for plugging issues with larger seed size and the use of seed treatments. By drawing air from the CCS tank the vacuum source is now cleaner, preventing meter debris buildup.

The row-unit head is also designed using the ductile iron-casting process. The row-unit head provides the mating joints between the row-unit parallel arms and the row-unit shank. It is also the upper attaching point for the seed meter and seed hopper.

The MaxEmerge 5 row-unit also provides better Tru-Vee opener bearings for longer life. The double-row ball bearing provides up to three times the wear life as the single-row bearing.

John Deere planters provide consistent seed depth control in all field conditions. Depth control is a function of the Tru-Vee openers, the downforce system, and the gauge wheel assembly.

The bolt-through design utilizes an open bearing in the gauge wheel that allows an attaching bolt to pass through the wheel to the threaded hole in the gauge wheel arm. This simple bolt-through design provides for a positive attachment of the gauge wheel to the gauge wheel arm and allows quick removal of the gauge wheel for service.

Rubber tire closing systems are used for most conventional, minimum-till, and no-till planting conditions. The spacing between the wheels is adjustable so the closing system can meet the needs of those who want to plant small seeds at shallow depths.

The wheels can also be staggered fore and aft to enhance residue flow. Four levels of spring force are available and are easily set with the integrated T-handle adjustment. A lower force spring can be obtained from parts, if a lower amount of force is required.