replacing hydraulic pump on log splitter pricelist

new member here trying to figure out how to fix my wood splitter. i have an older model mtd wood splitter, 25 ton i believe. this was my father"s and it had been sitting up for about 6 years before i brought it to my house to start using. the rubber gasket b/w the couplers had dry rotted and i couldnt figure out what size i needed so i thought i would take them off and take them to the local small engine shop to make sure i got the right size. the coupler on the shaft for the hydraulic pump was real tight and i ended up breaking the shaft. i have found the replacement pump for this splitter and it is $600, which is a little too much for me to stomach spending on this thing. my question is this: would it be possible to buy another pump which is cheaper to replace this one with? if so, what should i look for to make sure it is compatible?

i am also going to try and take the pump apart to see if i can take it to a machine shop and have a new shaft built, but i have been told that if i mess up any of the seals then it will be worthless b/c they dont make any replacement parts for this pump. thanks for any advice

This 2-Stage pump fits a wide variety of log splitters and outdoor power equipment and works in both horizontal and vertical orientations. The included inlet nipple requires a 1" inner diameter suction hose.

Rated for up to 3,000 PSI at 3,600 RPM, this pump can power log splitters from 5 to 35 tons, depending on the inner diameter of the hydraulic cylinder. It features a fast cycle time by moving quickly when unloaded. It automatically shifts to low-flow/high-pressure mode at 500 PSI.

Be sure to use AW-32 10-Weight (ISO 32) or AW-46 20-Weight (ISO 46) light hydraulic fluid or Dexron III automatic transmission fluid. This pump is not designed for use with “universal” or "tractor" transmission oil, such as "303". The use of incorrect fluid may damage the pump and void the warranty.

Make sure the hydraulic fluid reservoir is not below the pump to ensure a sufficient flow of fluid to the pump. Suction-side filtration should be no finer than 150 microns. The use of a 10-25 micron filter on the suction side of the pump is too restrictive and will cause failure.

We recommend using an L-style jaw coupling to connect the pump to an engine. Couplings and mounting brackets are available. You should use at least a 5hp 163cc engine to maintain 3,600 RPM under load.

"Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

· 16GPM Powerful Pump: This hydraulic pump comes with a 25 GPM auto control detent valve. It features a 3600 RPM max rotating speed, 2250PSI valve setting along with a 16GPM high flow rate. It will bring powerful performance to your log splitter. Get ready to start cutting logs in half, in half the time.

· 1" Inlet & 1/2" NPT Outlet: Our log splitter pump is equipped with a standard 1/2" NPT outlet port ( for Minimum 8 HP engine) and 1" barb on the inlet port. It also has a 1/2" diameter shaft with a 3/8" key, allowing it to rotate clockwise. Quality you can trust, for unmatched results you can see.

· Sturdy ＆ Durable: The high-strength extrusion aluminum casing enables the pump to resist impact, rust, and high pressure. This sturdy structure can prevent leaks and ensure a prolonged service life.

· Simple Installation: This pump stands out with a 4-hole bolt-on design, and it allows for a direct and quick installation. Install the pump effortlessly, making your log splitting more effective and robust.

· Doesn"t Just Split Logs: The 2-stage hydraulic pump is excellent for log splitters, press, machine tools, and power units for snowplows. It has outstanding compatibility with many OEMs like Speeco, Huskee, Champion, and many more.

Log splitter cylinders by Magister Hydraulics are heavy-duty and premium quality hydraulic equipment that can withstand up to 3500 psi operating pressure. It represents the most basic fluid power application offering cost and energy-saving benefits for the users. Our premium quality log splitter can help you save plenty of time and labor-intensive work. It can help to complete various jobs in different industries, such as technology, forestry, domestic settings, and other mobile hydraulic applications.

Made from quality steel and chrome plating, log splitters hydraulic cylinders can handle the toughest wood splitting jobs without disappointment. High tensile honed cold drawn tube for durability. High tensile ground & polished hard chrome plated rod. Base end of the cylinder comes with a welded clevis mount for added strength and durability. Rod end comes with a drilled pin-hole for added flexibility and customization. Rod seals are composed of high quality U-cup polyurethane with inner O-ring, POM-C wear rings and polyurethane wiper. Bore size available in 4” and 5” and stroke of 24” and 30”. Log Splitter cylinders features ½ NPT oil ports. The replacement parts are also available, making them a great choice to build your log splitter. Due to the simplicity and reliability of hydraulic log splitters, many people prefer them over electric or gas alternatives. You can use them with different equipment for log splitting like a skid steer, electric, gas, or 3 point tractor. We have log splitters in varying sizes.

At Magister Hydraulics, we are committed to delivering complete customer satisfaction with our products and services. We have products from the leading European manufacturers with a 2-year warranty and free shipping. Plus, we offer special discounted prices for bulk orders. If you need further assistance with the choice of products or parts, you can get in touch with us at 973-344-5313.

Log splitter cylinders by Magister Hydraulics are heavy-duty and premium quality hydraulic equipment that can withstand up to 3500 psi operating pressure. It represents the most basic fluid power application offering cost and energy-saving benefits for the users. Our premium quality log splitter can help you save plenty of time and labor-intensive work. It can help to complete various jobs in different industries, such as technology, forestry, domestic settings, and other mobile hydraulic applications.

Made from quality steel and chrome plating, log splitters hydraulic cylinders can handle the toughest wood splitting jobs without disappointment. High tensile honed cold drawn tube for durability. High tensile ground & polished hard chrome plated rod. Base end of the cylinder comes with a welded clevis mount for added strength and durability. Rod end comes with a drilled pin-hole for added flexibility and customization. Rod seals are composed of high quality U-cup polyurethane with inner O-ring, POM-C wear rings and polyurethane wiper. Bore size available in 4” and 5” and stroke of 24” and 30”. Log Splitter cylinders features ½ NPT oil ports. The replacement parts are also available, making them a great choice to build your log splitter. Due to the simplicity and reliability of hydraulic log splitters, many people prefer them over electric or gas alternatives. You can use them with different equipment for log splitting like a skid steer, electric, gas, or 3 point tractor. We have log splitters in varying sizes.

At Magister Hydraulics, we are committed to delivering complete customer satisfaction with our products and services. We have products from the leading European manufacturers with a 2-year warranty and free shipping. Plus, we offer special discounted prices for bulk orders. If you need further assistance with the choice of products or parts, you can get in touch with us at 973-344-5313.

Here at Beiler Hydraulics we stock a full range of log splitter pumps. Log splitter pumps automatically switch from high-speed/low-pressure to high-pressure/low-speed to meet the load requirements. The low-pressure side is preset at 400-900 psi, and the high-pressure side has a max of 3,000 psi. These pumps are ideal for log splitters, presses, or any application where you need to automatically switch from high speed at low pressure to high pressure at low speed. Beiler Hydraulics also stocks many other Log Splitter Parts including valves, cylinders, hose assemblies, and fittings. With our multi-million dollar inventory we are more than equipped to provide a complete solution for all your hydraulic needs. Our sales team has the knowledge and expertise to make sure you have exactly what you need. At Beiler Hydraulics we believe in offering quality products at competitive prices and providing the customer service you need before, during, and after the sale. Please Contact Us today with any questions or to place an order.

If the hydraulic hoses wear out and start leaking hydraulic fluid, the extreme pressure that"s forcing the fluid through the leak can be enough to strip the skin from your hand.

Contaminated hydraulic fluid can gradually reduce the efficiency of your wood splitter. A hydraulic ram that dries out could rust and damage the seal surrounding the shaft that holds in the hydraulic fluid.

On your wood splitter, you"ll find hoses or pipes running from the reservoir to the ram cylinder. These are the hydraulic pressure hoses, and they transfer the fluid from the reservoir to the cylinder to create pressure.

The pressure that"s created can be several tons per square inch. If you suspect you may have a worn hose that"s leaking, do not feel around for it. Several tons of pressure leaking out through a small hole is enough to rip open your hand.

Annually check your hydraulic fluid reservoir for water. Water contamination in your hydraulic fluid can build up over time, and can be identified as a milky grey discoloration in the fluid.

This contaminated hydraulic fluid will gradually decrease your wood splitter"s efficiency. So gradually, in fact, that you may not even notice it right away. But over time, it will make for a poorly functioning log splitter.

Another obviously important part of your hydraulic log splitter is the ram. You need to keep the ram fully greased up. Keep every square inch of it greased, because a dry ram will quickly become a rusty ram.

Rusted rams will damage the hydraulic seal, and you donotwant to damage the seal. If you notice rust forming, sand it off, clean it, and apply more grease.

Check out the carburetor to make sure your engine"s running efficiently. Remove the spark plug and check the plug gap and inspect the condition of the electrodes. A healthy engine is just as important as a healthy hydraulic system.

As soon as you notice significant fraying of the pull cord, go get yourself a new cord and replace the worn one. Then you"ll know it"s ready to go again when you need it.

The pump in your hydraulic system is driven by the engine. It usually utilizes a power take off coupling to operate it, so check the coupling for loose play.

If you can, check the central spindle of your pump to ensure it"s not getting too loose. If there"s too much play to either of these components, it could cause the pump to fail when it"s under pressure.

While you can"t reallytightenthese parts, you can change out the bearings. Looseness in the coupling and the central spindle are generally caused by damaged bearings, so try replacing them if you notice them getting a bit sloppy.

The only sources of excessive vibration are the hydraulic pump and the engine. So if you hear or feel your log splitter vibrating too much, it could indicate a problem with one of these two components.

Lastly, don"t worry yourself too much. It"s unlikely that you"ll have several malfunctions to deal with simultaneously. Just make sure to stay on top of your maintenance procedures, and your log splitter should last you many, many years

Once your order is packed and ready, our courier/freight trucks will collect your product directly from our warehouse. All orders purchased before 12pm will be dispatched from our warehouse on the same day!

All shipping prices can be calculated on the product and checkout pages within our website. If you are unsure of any shipping prices, please feel free to phone our store on 0800 DEAL MART and one of our friendly team members will be happy to help.

This pump is a Hi-Lo unit, which means it closes your blade quickly, then produces maximum PSI to split the wood. It is rated to 3600RPM max. This pump requires a minimum of 15 HP

Hi, Lo two stage pumps are by far the best option for log-splitting setups. Their ‘Magic’ is that you can achieve much higher PSI & flows( = speed & max tonnage!), with little HP compared to a regular hydraulic pump.

Hi, Lo hydraulic pumps operate in two modes. When there is no load (on the return stroke), they pump a larger volume at low pressure and move the cylinder back quickly. When the ram hits the wood the pressure increases and the pump switches to high pressure / low flow mode. A hi-lo pump speeds up the whole cycle process due to the fact that most of the time, the cylinder is moving with little or no load, which requires less power & less force to move the splitting ram. This pump requires a minimum of 15 HP. If not enough HP is available, the pump will not be capable of making high enough PSI, which in turn creates the high tonnage required. Tonnage will be determined by the Bore size of your ram, for example, a 4" bore ram will produce 16 tonnes @ 3000 psi, whilst a 5" bore ram will produce 26 tonnes @ 3000 psi