mud agitator brandt manufacturer

The skid mounted MA-RG agitator is compact, and its low profile reduces headroom requirements and provides more layout space on top of the tanks. The gearbox is a triple-reduction helical-bevel gear drive system that reduces the rotational speed of the motor to drive the impeller(s). Up to 95% mechanical efficiency helps reduce horsepower requirements.

Impellers are available with flat blades (radial flow), contour blades (axial flow), and canted blades (radial/axial flow). The impellers are sized according to tank volume and expected duty. Active mud system compartments—such as solids removal sections, mud mixing sections, and slug pits, which need a higher shear force to produce immediate mixing—are another consideration in impeller sizing.

BRANDT™ Agitators serve the drilling industry with quality, time-proven mechanical agitation. The horizontally mounted MA series agitator has been the industry standard for many years. Its rugged design, simplicity and dependability have made it the preferred choice of a majority of operators and contractors. The low profile of horizontal agitators reduces headroom requirements.

The Vertical Mechanical Agitator (VMA) series is ideal for installations with limited footprint availability. These double-reduction, in-line, helical gear agitators provide smooth, vibration-free operation and efficient mixing, just like the right-angle drive agitators.

VMA series agitators align the motor shaft with the gear reducer output shaft. The explosion-proof, C-face motor bolts on and couples to the double reduction helical gearbox. The entire assembly bolts to a fabricated steel base plate, which is then mounted on the tank.

Vertically mounted agitators are lighter than right-angle-drive horizontal units, but produce the same mixing results. In some instances, horsepower requirements are reduced due to the 95% efficiency of the helical gearing.

requirements and provides more layout space on top of mud tanks. The triple reduction helicalbevel gear drive system reduces the rotational speed of the motor to drive the impeller(s). Up to

Fluid Systems mud agitators are designed to mix and suspend the solids using axial flow, promoting low particle size degradation and effective polymer shear. Unlike mud guns, the FSI mud agitator is relatively a low energy device, easy to operate and inexpensive to maintain. Our standard horizontal and vertical mud agitators range in 5 to 30 horsepower with an explosion proof motor and gear reducer. We size mud agitators according to the configuration and maximum mud weight.

JBQ series mud Agitator, Less than 5.5 kW drilling mud Agitator adopts the blender cycloid speed reducer, and it is applied to the drug liquids mixing tank. This mud agitator has the advantage of compact structure so it occupies small area. More than 7.5 kW Mud Agitator uses the turbo and worm gear speed reducer, with the large torque transmission、 the revolution is steady、it works reliablely and has great merit. Common model of mud agitator is JBQ5.5kW 、JBQ7.5kW 、JBQ11kW and JBQ15kW.The drilling mud agitator is an important components for GN Solids Control drilling fluids processing system.

GN Solids Control as a professional manufacturer for soilds control equipments, we have designed lots of high-quality products, and JBQ series Agitator is one of them. To keep both the mud uniformity and the suspension of solids, the mud agitator is used to agitate the mud consecutively and reliably.This agitator agitates the mud to make cuttings, silt and sand pass the solids control system without being precipitated onto the tank bottom. Due to the simplex turbine decelerator, this product is featured by compact construction, light weight, balanced transmission, low noise, high efficiency of transmission and strong agitating power. Therefore, it is a reliable product in the solids control system.

China manufacturer GN Solids Control offer the world with drilling mud agitator equipments.We are an exporter of drilling fluid mud agitator for Indian, Russian,middle east.etc..Our factory and company are Quality Management System ISO 9001-2000 certified.GN Solids Control operate international oil gas drilling mud separation system sales,service,manufacturing,distribution serivce.Buy drilling fluid mud agitatorfrom China manufacturer.Your best mud agitator for drilling mud circulation system.

BETTER produce high-efficiency mud agitator, equivalent to BRANDT™ Agitators MA series, its rugged design, simplicity and dependability have made it the preferred choice of a majority of operators and contractors.

Brighway Solids Control is one of the Mud Agitator Suppliers in the world. Mud Agitator Power includes 5.5kw Mud Agitator, 7.5 kw Mud Agitator, 11kw Mud Agitator, 15kw Mud Agitator etc.

As we know, there are many good Mud Agitator Suppliers in the oilfield, such as Derrick, Brandt NOV, Swaco etc. Brightway company is also good Mud Agitator Supplier from China. Brightway Mud Agitators are manufacture as the international standard, so  can be used oilfield mud tanks or drilling mud system.

Brighway BWJBQ series mud agitators is widely used in the 200bbl 500bbl 600bbl mud tanks of drilling rig mud system. As the Mud Agitator Supplier, At present, Brightway BWJBQ series mud agitators had been exported to 40+ countries. such as: UAE, Saudi Arabia, Iraq, Iran, Kazakhstan, Pakistan,Poland, Turkey, Australia, New Zealand, India, Indonesia, South Korea, Thailand, Malaysia, Singapore, Taiwan, Egypt, Nigeria, Brazil, Argentina and Venezuela etc.

Compare other Mud Agitator Suppliers, Brightway can supply the customized Mud Agitators according to the customers request. for exmple, the Mud Agitators impellers can be design the single impeller or duble impellers, also the length of Mud Agitatormud agitators shaft can be design according to the deepth of the mud tanks. More useful information about mud agitators :Four Mud Agitator Impeller Type

In the oil drilling industry, there are manydrilling mud agitator companies in the world, such as brandt nov mud agitator company, derrick mud agitator company, mi swaco mud agitator company. The mud agitators they produced are used in many oil field drilling mud systems, so they are famous and profecional Drilling Mud Agitator Companies in the world.

In China, there are also many drilling mud agitator companies, Brightway Solids Control Co., Ltd is one of them. Brightway Company is the solids control equipment manufacturer in oil and gas drilling industry , and the mud agitators is the one of main products.

As a the the mud agitators company from China, Brightway is also can manufacture types mud agitators for drilling mud system, such as horizontal mud agitator and vertical mud agitator, ( if you want know more about horizontal mud agitator and vertical mud agitator, you can visit the page: http://www.solidscontrolsystem.com/horizontal-mud-agitator-and-vertical-mud-agitator-for-mud-tank/ ) and the power mud agitators of 10hp 7.5kw, 15hp 11kw, 20hp 15kw, 30hp 22kw etc. BWJBQ series mud agitator can be exported to the more than 40 countries. such as: Singapore, Indonesia, Malaysia, Thailand, Philippines, India, Pakistan, UAE, Saudi Arabia, Qatar, Dubai, Iran, Iraq, Egypt, Russia etc.

Mud agitator is an important part of the drilling-fluid solids controling system. Drilling fluids agitatorcan be installed on drilling fluid tank, with the impeller submerged into certain depth under fluid surface to stir the fluid directly.During this process, the drilling fluid can be mixed even, and the solid particles are eliminated.In this way, it can improve solid phase dispersion, and increase the viscosity and gel strength, thus to make drilling fluid keep accordant with the requirement, provide needful fluid for drilling process, and ensure the smooth going of drilling work.Drilling mud agitator is the same as mud agitator.

TR solid control provide vertical and horizontal agitator. Horizontal mud agitator is divided into coupling type and direct type agitator. If you need a horizontal mud agitator, we recommend you use a direct type agitator. drilling mud Agitator is an ideal device for stirring, mixing liquid and preventing the solid-phase precipitation in the mixture.

Drilling Fluids Agitator in the mud system used to,mixing ratio and prevent to the mud tanked.TR solid control is an exporter of centrifugal pump . We are an exporter of drilling fluids mud agitator.Our factory approval the ISO9001,drilling agitator have the API certification.TR solids control is the designed,selling,production,service and delivery of Chinese mud agitator manufacturer. We will provide the high quality drilling fluids agitator and best service.Your best drilling mud tank agitators start from TR solids control.

The MAX2000® Agitator features a rugged cast iron gearbox that houses helical bevel gearing. The gear sets are precisely ground to prevent all but the slightest amount of backlash in the gear sets. This feature promotes longer life by eliminating the high impact forces generated when the unit is energized at start-up. Each helical bevel gear stage is 98% efficient. A typical worm gear set is only 85% efficient, since it loses most of its efficiency through the generation of heat.

Internal gears and bearings are lubricated with mineral oil. When the ambient temperature drops below 23ºF or rises above 140ºF, a synthetic lubricant should be substituted. A unique feature of the MAX2000® Agitator is the lower bearing, which can be maintained from the top of the tank. This feature eliminates the need for in-tank inspections of the lower bearing, and also provides a barrier of grease that can be expunged out the lower seal. The lower seals are arranged to accommodate the grease pocket and make for a four-tier layer of protection for the gearing. The end result means the lower bearing stays in contact with good, uncontaminated lubricant at all times. All four of these levels must be breached prior to loss of oil in the gearbox.

Lightweight, but sturdy construction with the highest torque rating in the industry. Example: 15 hp KOE Agitator weighs 246.4 kg compared to industry average of 831.8 kg)

Brandt agitators serve the drilling industry with quality, time- Vertically mounted agitators mount the motor in line with the proven mechanical agitation. The Brandt horizontally mounted gear reducer and output shaft. The explosion-proof, C-face MA™-series agitator has been the industry standard for many motor bolts on and couples to the double reduction helical years. Its rugged design, simplicity and dependability have gearbox. The entire assembly bolts to a fabricated steel base made it the preferred choice of a majority of operators and plate, which is mounted on the mud pit. contractors. The low profile of Brandt horizontal agitators reduce Vertically mounted agitators are lighter than right- headroom requirements. They come in two styles. angle-drive horizontal units, but produce the same mixing Brandt’s original MA™ series with 30:1 single results. In some instances horsepower requirements are reduction worm-gear drive that uses a sliding action worm and reduced due to the 95% efficiency of the helical gearing. gear. Available in 3, 5, 7.5, 10,15, 20, 25, and 30 HP. Impellers Brandt’s new MA-RG (Right Angle Gear) double Brandt agitators are available with three types of reduction,helical gear designed primarily for applications impellers and are sized according to tank volume and expected requiring more than 15 horsepower can be used for large duty. Active mud system compartments (such as solids displacement applications. Up to 95% mechanical efficiency removal sections, mud mixing sections and slug pits) need a helps reduce horsepower requirements compared to conven- higher shear blade to produce more immediate mixing. tional designs. Therefore Brandt recommends either a flat blade or canted The 1:1 ratio of height-to-width of both designs blade, depending on tank depth. Bulk storage compartments results in a low center of gravity, providing stability and safety. need a low-shear blade that maintains suspension in a gentler Brandt VMA™series (Vertical Mechanical Agitator) is manner. ideal for installations with limited footprint availability. These For active mud system compartments less than 5 feet double-reduction, inline, helical gear agitators provide smooth, in height, a flat blade impeller can be used to induce radial flow vibration-free operation and efficient mixing, just like right-angle patterns in the mud. Flat bladed impellers should be placed Brandt agitators. approximately six inches above the tank or two inches above the bottom shaft stabilizer, if one is used. Brandt Agitators™

When compartment height is greater than 5 feet, either a 60- Regardless of what style agitator or impeller is used, properdegree canted impeller, or a high volume contour blade is used sizing is critical. Impeller sizes are determined by calculatingto promote axial as well as radial flow. Canted impellers should the TOR (Turn Over Rate) for each agitated compartment. TOR isbe placed on the shaft so that the distance between the bottom of the time required, in seconds, to completely move the fluid in athe tank and the lower edge of the impeller blades is equal to ¾ mud tank and can be calculated by knowing the tank volume andthe diameter of the impeller. For tanks deeper than 12 feet, two impeller displacement.or more impeller blades may be used in combination. Vt TOR = × 60 For bulk storage tanks, high-efficiency, contour Dimpellers are best. This variable pitch impeller reduces Vt = Tank volume gallonshorsepower requirements and induces less shear to the mud. D = Impeller displacement in gpm (as calculated Shafts by Brandt engineering staff and displayed in chart above) Manufactured of solid mild steel, the agitator shaft is For tanks sized to metric specificationscoupled to the gear reduction assembly with a rigid coupling. All Vt = Tank volume litersshafts are keyed at the bottom for adjustment of impeller height. D = Impeller displacement in lpm (as calculatedA bottom end stabilizer is supplied when tank depths exceed 6 by Brandt engineering staff and displayed in chart above)feet. The stabilizer reduces side loading and protects the agitator For 60-degree canted blade applications TOR shouldwhen auxiliary equipment is carried inside the mud tanks during be between 40 and 90 seconds. As the TOR approaches 40rig moves. seconds, the chance for air entrainment increases. At TOR greater than 90 seconds, proper suspension may be jeopar- T Y P I C A L T U R N O V E R R A T E P E R C O M P A RT M E N T dized and solids will begin to settle. SHAKER INTERMEDIATE SUCTION RESERVE PILL For contour blade applications, TOR must be signifi- Canted 50- 75 50- 75 65- 85 50- 80 40- 65 Impeller cantly faster to achieve the same results, but because of the Contour 25- 38 25- 38 32- 42 25- 40 20- 32 100% axial flow, air entrainment is not a problem. Blade Brandt Agitators™

Model HP Length Height Width Min. Impeller Shaft Shaft Agitator Length Height Width Min. Shaft Shaft Agitator (in) (in) (in) Dia. (in) Diameter Wt. Less Shaft (mm) (mm) (mm) Impeller Diameter Wt. Less Shaft Canted - Contour (in) (lbs/ft) & Impeller Dia. (mm) (kg/m) & Impeller Wt. (lbs) (mm) Wt. (kg)MA3 3 35 1/4 15 11/16 19 9/16 24 28 1 3/4 8 1/4 406 895 398 497 610 44 12 184MA5 5 40 1/4 16 3/4 21 9/16 28 34 2 3/8 15 580 1022 425 548 711 60 22 263MA7.5 7.5 52 1/8 24 1/4 27 5/8 32 38 2 3/8 15 1200 1324 616 702 813 60 22 544MA10 10 52 1/8 24 1/4 27 5/8 32 42 3 24 1224 1324 616 702 813 76 36 555MA15 15 52 1/8 24 1/4 27 5/8 36 48 3 24 1320 1324 616 702 914 76 36 599MA20 20 61 1/4 27 1/8 34 1/4 40 52 3 1/4 28 1898 1556 689 870 1016 83 42 861MA25 25 68 5/8 30 7/8 39 1/2 40 60 3 1/2 32 3/4 3130 1743 784 1003 1016 89 49 1420MA30 30 68 5/8 30 7/8 39 1/2 40 64 3 1/2 32 3/4 3180 1743 784 1003 1016 89 49 1442

Brandt agitators provide more thorough mixing of pits and Contact Brandt for proper agitator sizing. eliminate the problems associated with mud guns, such as Specifications are subject to change without prior notice particle degradation and gun nozzle washout. Brandt agitators can be sized to fit any mud system or type of duty. From Flowline To Disposal, Brandt has the solution to your separation and waste management Western Hemisphere Eastern Hemisphere Phone: (713) 856-4100 Phone: 44-1224-343600 problems. We are one of the Varco Companies; technology Fax: (713) 856-4133 Fax: 44-1224-343700 leaders to the drilling industry. www.varco.com brandt-rigtech-uk@varco.com This is not a complete list of all locations. Call for the location nearest you.