mud agitator schootel made in china

Derrick mud agitators include an explosion-proof, “C” faced motor, reduction gearbox (helical-bevel gears for horizontal agitators or all helical gears for vertical units), impeller, and shaft with assembly bushings. Motors range from 5 to 30 HP and may be supplied in several power configurations.

Attaching the motor directly to the gearbox protects correct alignment that can increase bearing life and provides 95 percent efficiency in power transfer to the impeller. Using this superior design surpasses standard worm drive gear assemblies by 30 percent, allowing Derrick agitators to do the same work at far less horsepower. By unitizing the motor and gearbox, weight and space requirements are reduced. Horsepower, mechanical configuration, impeller diameter, and shaft length are customized to tank dimensions and maximum mud weights. Available horsepower ratings* are: 5, 7.5, 10, 15, 20, 25, and 30.

The MAX2000® Agitator features a rugged cast iron gearbox that houses helical bevel gearing. The gear sets are precisely ground to prevent all but the slightest amount of backlash in the gear sets. This feature promotes longer life by eliminating the high impact forces generated when the unit is energized at start-up. Each helical bevel gear stage is 98% efficient. A typical worm gear set is only 85% efficient, since it loses most of its efficiency through the generation of heat.

Internal gears and bearings are lubricated with mineral oil. When the ambient temperature drops below 23ºF or rises above 140ºF, a synthetic lubricant should be substituted. A unique feature of the MAX2000® Agitator is the lower bearing, which can be maintained from the top of the tank. This feature eliminates the need for in-tank inspections of the lower bearing, and also provides a barrier of grease that can be expunged out the lower seal. The lower seals are arranged to accommodate the grease pocket and make for a four-tier layer of protection for the gearing. The end result means the lower bearing stays in contact with good, uncontaminated lubricant at all times. All four of these levels must be breached prior to loss of oil in the gearbox.

JBQ series mud Agitator, Less than 5.5 kW drilling mud Agitator adopts the blender cycloid speed reducer, and it is applied to the drug liquids mixing tank. This mud agitator has the advantage of compact structure so it occupies small area. More than 7.5 kW Mud Agitator uses the turbo and worm gear speed reducer, with the large torque transmission、 the revolution is steady、it works reliablely and has great merit. Common model of mud agitator is JBQ5.5kW 、JBQ7.5kW 、JBQ11kW and JBQ15kW.The drilling mud agitator is an important components for GN Solids Control drilling fluids processing system.

GN Solids Control as a professional manufacturer for soilds control equipments, we have designed lots of high-quality products, and JBQ series Agitator is one of them. To keep both the mud uniformity and the suspension of solids, the mud agitator is used to agitate the mud consecutively and reliably.This agitator agitates the mud to make cuttings, silt and sand pass the solids control system without being precipitated onto the tank bottom. Due to the simplex turbine decelerator, this product is featured by compact construction, light weight, balanced transmission, low noise, high efficiency of transmission and strong agitating power. Therefore, it is a reliable product in the solids control system.

China manufacturer GN Solids Control offer the world with drilling mud agitator equipments.We are an exporter of drilling fluid mud agitator for Indian, Russian,middle east.etc..Our factory and company are Quality Management System ISO 9001-2000 certified.GN Solids Control operate international oil gas drilling mud separation system sales,service,manufacturing,distribution serivce.Buy drilling fluid mud agitatorfrom China manufacturer.Your best mud agitator for drilling mud circulation system.

Drilling mud agitator is widely used in drilling mud systems. It is equipped in all kinds of mud tanks to avoid solids settling down, like in sand trap, mixing tank, reserve tank, centrifugal tank, etc…

The Mud agitator is composed of driven motor and gearbox. The motor and gearbox are connected via coupling or flange, and driven the shaft to rotate. There are canted impeller / impellers fixing on the shaft to protect the drilling mud from settling down.

According to the connection face of driven motor and gearbox, there are horizontal mud agitator and vertical mud agitator. Clients choose the suitable model based on the mud tank situation.

GN Solids Control makes various sizes drilling mud agitator to fit for clients’ applications. This week, GN Solids Control finished some mud agitators for an offshore platform. The agitators are customized per client’s color. GN Solids Control make shaft to suit for the tank inner depth. And the canter impeller size and quantity is designed to accordance with the motor power and tank size. Plus, in order to avoid the agitator shaft hanging during rotating, GN Solids Control make tank bottom stabilizer to support the agitator shaft inside the mud tank. It can also improve the service time of the mud agitator.

During assembly, the operator should adjust the gap between the stabilizer and the shaft to make the gap between the stabilizer and the shaft uniform to ensure concentricity. If the concentricity of the stabilizer and the shaft cannot be guaranteed, the agitator will be noisy and the gearbox reducer will be easily damaged.

Correct and suitable lubrication is vital to ensure stable running of mud agitators. Most problem of mud agitator are caused by unsuitable lubrication, or the lock of lubrication.

Double Life Mud Agitators are used within the Oil and Gas, Horizontal Directional Drilling (HDD), Chemical, & Water Well Drilling industries. Double Life manufactured Mud Agitators utilize the benefits of a USA Made Helical Bevel Gear Box with Heavy Duty Bearings, Solid Shafts, Keyless Couplings, Synthetic Oil, & Canted Impeller Blades. These Agitators are low maintenance and keep your pits continually in motion. With our low clearance and ease of service, our mud agitators are an easy choice for a contractor!