duplex mud pump parts price

We stock fluid end parts for the5×6 mud pump, 5×6-1/4 FM45 mud pump, 5×8 mud pump, 5-1/2×8 mud pump, 5X10 mud pump, 4-1/2×5 mud pump, 7-1/2×8 mud pump, and 7-1/2X10 mud pump.  The Gardner Denver mud pump model numbers for the above pumps are as follows: 5X6-FGFXG, 5X8-FDFXX, 5-1/2X8-FDFXX, 5X10-FDFXD, 4-1/2X5-FFFXF, 7-1/2X8-FYFXX, 7-1/2X10-FYFXD.  We also handle Wheatley, Gaso, Worthington, Failing and Centerline parts and pumps. We also stock Foot Valve, Liner Puller, Valve Seat Puller, (4″ Inline Check Valve.  Our Gardner Denver mud pump parts are not only competitively priced, they are also made in the USA.  Oil Recommended by Gardner Denver.  Call any of our experienced representatives to get the help and knowledge you deserve.

A mud pump is a reciprocating piston/plunger pump designed to circulate drilling fluid under high pressure (up to 7,500 psi (52,000 kPa)) down the drill string and back up the annulus. A duplex mud pump is an important part of the equipment used for oil well drilling.

Duplex mud pumps (two piston/plungers) have generally been replaced by the triplex pump, but are still common in developing countries. Two later developments are the hex pump with six vertical pistons/plungers, and various quintuplex’s with five horizontal piston/plungers. The advantages that Duplex mud pumps have over convention triplex pumps is a lower mud noise which assists with better Measurement while drilling and Logging while drilling decoding.

Use duplex mud pumps to make sure that the circulation of the mud being drilled or the supply of liquid reaches the bottom of the well from the mud cleaning system. Despite being older technology than the triplex mud pump, the duplex mud pumps can use either electricity or diesel, and maintenance is easy due to their binocular floating seals and safety valves.

A mud pump is composed of many parts including mud pump liner, mud pump piston, modules, hydraulic seat pullers, and other parts. Parts of a mud pump:housing itself

Duplex pumps are used to provide a secondary means of fuel transfer in the event of a failure of the primary pump. Each pump in a duplex set is sized to meet the full flow requirements of the system. Pump controllers can be set for any of the following common operating modes:Lead / Lag (Primary / Secondary): The lead (primary) pump is selected by the user and the lag (secondary pump operates when a failure of the primary pump is detected.

Alternating: Operates per Lead / Lag (Primary / Secondary) except that the operating pump and lead / lag status alternate on consecutive starts. A variation is to alternate the pumps based on the operating time (hour meter) of the lead pump.

Your search for superb quality oil well Drilling Parts ends at one stop shop that is Vision Auto Industries. Finding multiple applications in various industries, the drilling parts offered by us are appreciated andread more...

We are Authorized dealers for HAINUAO AO brand of mud pump spares which are compatible with mud pumps of EMSCO, GARDNER-DENEVER, NATIONAL OILWEL, IDECO, SKYTOP/BREWSTER, OPI WERTH WILSON and GASO and are an OEM replacement, approved by the API and are designed for the longest service.

Mud Pump Spare Parts, Conumables, Shale Shaker Screen, Shale Shaker Tension Bolt, Shale Shaker Cushion Rubber, Reeling Pins, Mud Tank Flapper Pins, Safety Pins, Safety Pins for Wiper Rubber, Drill Rod Wiper, BOP Spares, BOP Ram, BOP Studs, High Tensile Stud Bolts for Oilfield, Flanges, Butterfly Valves, Gate Valves, Globeread more...

Keeping in pace with the specific need of our customers, we are engaged in offering a wide series of Mud Pump Spare Parts. Our offered item is developed under the supervision of our skilled workers using finest quality basic material. This is well regarded among the clients due to its corrosion resistance, fine finish andread more...

Owing to the years of industrial experience, we have been able to serve our esteemed clients with a wide variety of Duplex Mud Pump Part. These parts of pumps are manufactured by our industry-experts using advanced machinery and premium quality material. Further, we check these parts on different parameters previous to theirread more...

p-500 / 50, mb-10 swivel, , ch-500/ 400/ 320/ 125 / 50/ t-50 mud swivel . Cardwell -6 w/o rig , bhel-2000 / 150 t swivel, wash pipe (short & long – russian work over mud swivel), a-50 (short), wash pipe with snap ring , rubber packing set are ready stock.read more...

At BOPM, we constantly maintain 5 million worth of mud pump parts on the shelf at our Houston warehouse location. It includes modules, liners, extension rods, piston rods, pistons , threaded rings, caps, valve covers, valve guides, valves, seats etc. for all major brands of pumps: Gardner Denver®, Ideco®, Emsco®, National®, Oilwell®, Skytop Brewster®, Lanshi(3NB1300C) ®, Bomco ®, HH ®.

BOPM offers a complete line of interchangeable fluid end modules and accessories for triplex mud pumps, such as National, Emsco, Gardner Denver, Bomco, Ideco and Oilwell. We offer both standard OEM style replacement parts and Two piece “L” Shaped fluid ends.

BOPM piston rods are made with premium grade, heat treated alloy steel. The rods offer excellent resistance to fatigue, corrosion and heavy loads. A full line of piston rods are available for various pumps.

BOPM extension rods are made from high strength alloy steel, and are either heat treated or chrome plated. The rod offers excellent resistance to fatigue, corrosion and heavy loads. BOPM extension rods are machined and polished to ensure a perfect seal to protect the mud pump gear end.

All of our gear set adopt high-end carburization heat treatment and precise grinding machining to offer unparalleled durability; first we use high strength alloy steel, then adopt the Carburization heat treatment to enhance the hardness and wearability, finally adopt the grinding fine machining to ensure the smooth gear teeth surface; Resulting in consistent and rugged performance throughout pump operation.

BOPM bonded urethane pistonsare constructed of urethane, bonded to a steel hub. The double durometer urethane is designed to provide optimal performance in oil or water based mud and high drilling pressures.

BOPM Replaceable Rubber Pistonis made with tough and durable Buna N rubber for all pressures, and is ideally suited for water-base mud. A special processing of the fabric provides an unusually waterproof bond of fabric to piston which assures longer life.

BOPM Bonded Rubber Pistonis made with tough and durable Buna N rubber for all pressures, and is ideally suited for water-base mud. A special processing of the fabric provides an unusually waterproof bond of fabric to piston which assures longer life.

Find your George E. Failing replacement parts quickly and easily. With over $1,000,000 of interchangeable pump parts in stock, American Mfg Company can fulfill your order, most orders ship the same day!

Danco Pump is your one-stop pump shop. We can provide complete service for all your pumping equipment. We have all power end and fluid end parts for all major high pressure reciprocating plunger and piston pumps. Wheatley Pumps; new, used and reconditioned pumps.

High pressure plunger and reciprocating piston pumps are used in many applications. Salt water injection and disposal, crude oil transfer and well servicing all use high pressure plunger pumps and piston pumps. Waste water treatment plants and sewer cleaning would require high pressure pumps as well to process the waste and water. Carwash, mud pumps and filter wash are other applications in which the pumps would be utilized.

We are the source for all your plunger and piston pump requirements. We have components for most major pump lines such as Gaso, Wheatley, Kerr, Gardener-Denver, Weatherford, National, Oilwell, Bethlehem , Tulsa Pump models.

A wide variety of emsco mud pump parts options are available to you, such as 1 year, not available and 2 years.You can also choose from new, emsco mud pump parts,as well as from energy & mining, construction works , and machinery repair shops emsco mud pump parts, and whether emsco mud pump parts is 1.5 years, 6 months, or unavailable.

triplex mud pumps and triplex mud pump parts meet the industry standards established by the American Petroleum Institute (API). As a global supplier of quality oilfield equipment to the oil and gas industry, we ship our products around the world.

Besides triplex mud pumps and triplex mud pump parts, we supply drilling rigs, workover rigs, top drives, drilling equipment, blowout preventers, BOP control systems, choke and kill manifolds, well service pumps for well cementing and hydraulic fracturing, wellhead equipment, casing heads, tubing heads, X-mas trees, FC type gate valves, etc. Please visit our company website

We supply unitized mud pump packages driven by DC or AC electric motors or diesel engines for electric and mechanical drilling rigs. The client can select DC or AC motors and diesel engine brands such as Caterpillar, Detroit, Cummins or others. Our unitized mud pump packages including everything on the skid and usually they are ready to work at delivery.

We carry mud pumps, connecting rods, and more than 2,000 drawings and blueprints of oilfield equipment and supplies. We can fill your orders with one-of-a-kind designs for:

Our vast inventory of fluid-end and gear-end parts for duplex pumps includes more than 500 duplex liners, as well as cages and stuffing boxes. If you can’t find the model you are looking for below, let us find it for you.

With more than $1,500,000 in parts and supplies, we have one of the largest inventories of drilling supplies in the United States. Have us serve your draw-work needs with a single phone call. We can build you a new EC 450 or EC 700 model down to the last detail, as well as custom draw-works services.

We carry more than 1,500 duplex piston rods and 200 duplex pony rods in our inventory. Though we keep in stock connecting rods primarily for GA550 and GA750 models, other options are available, including custom connecting rods for most duplex and triplex mud pumps.

We now offer crossheads and guides for both EMSCO D-375 and DB-550 duplex pumps. We also have slides and shoes for certain models. If you don’t see a part you need, let us find it for you.

EC Tool offers Oteco gate valves, Demco gate valves, O’Drill pressure relief valves, manifold valves, butterfly valves, ball valves, and check valves. We also maintain a large inventory of spare parts for most of the valves we carry, including drive bushings and rotating heads from Kelly and other well-known brands.

We are a supplier of aftermarket mud pump parts. Whether it’s a duplex or triplex pump, we offer a complete line of parts and spares that interchange with most brands. We supply everything from chrome and ceramic liners, seals, crankshafts, pistons and modules and everything in between.

Triplex: This mud pump is used for drilling applications needing high pump pressure. This model works by decreasing the working fluid volume being discharged to generate pressure for producing the flow. There are three pistons in the triplex pump, with the middle piston generating more pressure on the crankshaft. High piston load can lead to excessive pressure and crankshaft failure if the components are not properly sourced.

Quintuplex:Quintuplex mud pump is perfect for pumping fluid at the time of drilling operations. It works as a continuous duty return piston. This is used in terms of its external bearings to provide crankshaft support to ensure the proper functioning of the sheaves.

Duplex: These mud pumps ensure that the mud circulation reaches the well"s bottom from the mud cleaning system. Duplex pumps have binocular floating seals as well as safety valves.

Saigao offers high-quality OEM mud pump spares, consumables, expendables and spare parts. Our mud pump parts are made with the highest standards of quality, offering competitive pricing and exceptional durability.

If you work in oil and natural gas, you know what the two most valuable resources are – Time and Money. With our new Parts on Demand program, you can save more of both.

As part of Experience 360, our Parts on Demand program lets you manage your replacement parts inventory at your regional location, pump site, or even via GD Energy Products Parts on Demand mobile trailers.

These Frac and Mud Pump Consumables are OEM-certified parts, designed, manufactured and tested by our Pump experts, and proven to maximize the performance on your operation. Our parts are always available, ensuring you have what you need, whenever and wherever you need it.