lubi mud pump catalogue factory

Product data The Lubi LBM series are self-priming, horizontal, single-stage, centrifugal, end-suction pumps. Pumps are available from 0.75 to 2.2 kW in single-phase and from 0.75 to 7.5 kW in three-phase power supply. Motor and pump are close coupled in a convenient and compact design for quick installation in limited space. They are also available as bare pump unit which are suitable for coupling with motor / engine. The pump is fitted with a gland packing and single piece pump-motor shaft (in close coupled version). Mechanical shaft seal is available in 0.75 kW models. The pumps have...

Product data Operating conditions Head range The pump is fitted with a Totally Enclosed Fan Cooled, 2-pole or4-pole induction motors which performance Liquid temperature range: 0°C to +90°C Total suction lift : Up to 8 metres Pumped liquids These pumps are designed for liquids which are non- aggressive and non-explosive, muddy water, with or without solids up to 20 mm grain size or fibres. Pump location The pumps have been designed to operate in a non- aggressive and non-explosive atmosphere. The relative humidity should not exceed 95%. Curve conditions The conditions below apply to the...

Base frames Base frames The dimensional sketches below show the dimensions of the base frames fitted to LBS pumps. The type number of the base frame is stated for each LBS pump mentioned in the Technical data. Base frame type No. Base frame

Lubi Electricals Limited. Near Kalyan Mills, Naroda Road, Ahmedabad-380 025, INDIA. Sales Enquiries: mktsales@lubipumps.com, expsasles@lubipumps.com Product Improvement is a continuous process at "LUBI". The data given in this publication is therefore subject to revision.

Performance Range 4 Flow rate up to 1000 l/min. (60 m3/hr) ► Drainage of sewage from the building basements, hotel industry, waste water from factories. Drainage of sewage from industrial process factories. 4 Emptying fo septic tanks, cesspits and sewage pump ► Pumping surface and drainage water from garages 4 A precision manufactured motor is achieved utilizing a laminated sheet steel production process combined with the highest standard of quality control. The drive shaft and rotor assembly is heat - treated and the stator and wiring impregnated with varnish and then heat dried in an industrial oven. This ensures a 100°/ quality manufactured motor with stable characte ristics and a high efficiency. 4 Standard accessories include: VCT cable outlet pipe with an epoxy resin sealed water - resistant cable base, AC thermal motor protector, dual mechanical seal and lip seal design. Special Features on Request Thermal overload protector nt Equipped with Automatic reset motor protector, prevents motor from temperature/phase failure/ voltage drop and lock Cable base 4 Epoxy resin seal cable base to prevent water intrusion into motor through cutting foreign particles, solid media. generate rapid rotating vortex to handle fluid mixed with long fiber, impeller wear.

Lubi provides superior quality range of pumps which caters all needs of agriculture and brings pride to Indian farmer. We are one of the largest pump manufacturer and supplier. Lubi pumps aim to deliver quality to agriculture sector by offering wide range of Agriculture products like Cast Iron & Stainless Steel Borewell submersible pumps, Openwell Submersible pumps, Centrifugal monoblock Pumps, Self priming pumps etc.

Lubi has large variety in manufacturing industrial pumps. We offer pumps for industries which fit into several applications like dairy, pharma, fire fighting, HVAC etc system. Being one of the largest pump manufacturer and supplier we manufacture a wide range of Industrial product for water supply, like End suction pumps, Split Case pumps, Vertical In-line pumps, Multistage Centrifugal pumps, Sewage & Drainage pumps, Corrosion resistant Thermoplastic pumps, Coolant Pumps, Pressure booster systems, Induction Motors, etc.

Lubi deals with huge variety of drainage pumps which resolves an issue of draining flooded water in basements, car parking or at any location. Lubi has wide range of drainage products like Drainage & Sewage Pumps, Heavy Duty Construction Drainage Pumps Grinder Pumps, Propeller Pumps, Self Priming Mud Pumps, etc.

Lubi also delivers wide range of Fire Fighting Water Pump with considering safety to human life. We offer fire pumps which are UL/FM approved that ensures double safety to the premises as well as life of human. Lubi is one of the largest pump manufacturer and supplier by offering a wide range of Fire pump products for water supply like Horizontal Split Case Fire Pumps, Centrifugal End Suction Fire pumps, Multistage Multi Outlet Fire Pumps, Turbine Fire Pumps, Submerged Centrifugal Fire pumps, Vertical In-line pumps, Jockey Pumps, etc.

Lubi tackles the requirement of maintaining constant pressure or to boost the pressure in commercial buildings, apartments,residents and at so many places. Lubi manufacturing a wide range of Residential product for water supply, houses like Pressure Booster.

Lubi serves the needs of pumps to hotels, corporate, malls and to each residential place where heavy pressure, boosting is required. Lubi residential pumps are ideal for locations where constant pressure has to be maintained. Lubi aims to deliver quality pumps to customer by offering wide range of Residential products for water supply, houses, garden like Cast Iron & Stainless Steel Borewell submersible pumps, Openwell Submersible pumps, Self priming monoblock Pumps, Pressure Booster pumps, etc.

Lubi hits biggest milestone by offering excellent quality solar pumps. We are the leading solar module manufacturing company in India with automatic manufacturing of solar modules. We have diversified range in solar pumps. We offer wide range of solar products for water supply like Cast Iron & Stainless Steel Borewell submersible pumps, Openwell Submersible pumps, Centrifugal monoblock Pumps, etc.

Lubi pumps assist in treating waste water. Our pumps play vital role for collecting waste water from plant and supply it for further processing. Lubi is manufacturing a wide range of products like Drainage & Sewage Pumps, feed pumps, Self Priming Mud Pumps, Multistage centrifugal pumps, Corrosion resistant Thermoplastic pumps, etc.

The pump volute shall be of cast Iron as per grade FG 260 of IS 210/ISO 186 with vertical discharge port. The pumps shall have non clog semi open impeller with material of construction of Cast Iron (standard supply), CF8 and CF8M, suitable for pumping liquids up to 50 deg. C.

The Pump shaft sealing shall be accomplished with double mechanical shaft seal of material Carbon /Ceramic/NBR/AISI 304 Up to 1 Hp and above 1 Hp the mechanical shaft seal material shall be Sic/Sic /Viton /AISI 316 on the pump side.

The pump shall be close coupled with a dry submersible motor, having class F insulation, IP 68 protection, 2900 rpm, epoxy sealed cable entry, with S1 duty for fully submerged and S3 duty for partially submerged application.

We manufacture and market our complete product line under the brand name of “Lubi”. Our group has also been a dependable outsourcing partner for numerous European & American Companies for manufacturing products and their various components under their Brand name. We possess a well established clientele spread across more various parts of the country & also in across more than80 countries.

Our range of pumps is mainly supplied to leading Government Water Supply Boards, Cooperative Farming Societies, Leading Industrial Corporations and also to Global Dealers & Distributors.In addition, we also have a country-wide distribution network comprising of 1000 Dealers & Distributors.

We offer a wide variety of agricultural, Industrail and Domestic pumps that are appreciated across the world for their high quality, durability and performance. Our range comprises Bore Well Submersible pumps, Submersible motors, Pressure Booster Pump, High Pressure Pump, Single Phase Centrifugal Pump, Multi Stage High Pressure Pumps, Horizontal Split Case Pump, End Suction Pump, Shallow Well Jet Pump, Submersible Water Pump, Garden Pump, Monoblock Pump Sets and Sewage Pump.

2000Lubi Electricals Ltd., Mira Industries & Lubi Foundry were awarded ISO 9002 certification & Lubi Submersibles was awarded ISO 9001 certification by TUV, Germany.

Lubi Group of Industries proposes to establish product outlets in 80% of potential markets in the country in all its product range and will expand / penetrate into export markets for achieving growth.

Lubi Group of Industries will set up world class manufacturing facilities in all its product range and will offer quality products and services at competitive prices.

Lubi Group of Industries will provide value added engineering solutions for its industrial automation products & will also diversify into manufacturing of electronic products used in industrial application.

Lubi Group of Industries will implement excellent health & safety standards and welfare activities and will offer growth opportunities by developing people competencies.

Lubi Group of Industries aspires to become a preferred supplier of products and services. LGI will offer best customer value in all its business activities. LGI wants to achieve 20% annual compounded growth in existing sales turnover while maintaining / improving profitability.

We bring forth for the clients precision engineered Self Priming Mud Pump. This is offered in varied models & sizes and is provided in different industries such as thermal power plants, construction sites, chemicals and petrochemicals. Our product is provided along with interchangeable parts and is easy to maintain. The range offered by us is especially suitable for tile factories and marble factories for handling waste liquids.

Our range of products include non clog mud sewage pump, iron submersible sewage pump, submersible sewage pumps, self priming monoblock mud sewage pump, sewage submersible cutter pumps and self priming pump.

Solid Handle SizeUp to 50 mmWe facilitate our clients with Iron Submersible Sewage Pump, which is best in quality and excellent in performance. Impeller of these portable pumps is mounted directly onto the extended shaft of the motor. To give signal against ingress of water into the oil chamber, the pumps are also provided with sensing device. Manufactured using stainless steel and other alloys, these are durable and resistant to wear & tear. If the client demand for motor protection, sensors are provided in windings which trip the circuit on reaching a preset temperature.

Delivery Size32 mm to 100 mmWe facilitate our clients with Submersible Sewage Pumps, which is best in quality and excellent in performance. Impeller of these portable pumps is mounted directly onto the extended shaft of the motor. To give signal against ingress of water into the oil chamber, the pumps are also provided with sensing device. Manufactured using stainless steel and other alloys, these are durable and resistant to wear & tear. If the client demand for motor protection, sensors are provided in windings which trip the circuit on reaching a preset temperature.

We deal in Sewage Submersible Cutter Pumps.It is used in wastewater treatment plant, medical waste disposal, industrial waste disposal, mud treatment plant, hotel waste management, ext.

PressureUp to 5.5 kg/cm2We deal in different series in Self Priming Mud Sewage Pumps. This is also known as Self-Priming Non-Clog mud/sewage Pump; Self-Priming Non-Clog mud/sewage pump with Mechanical seal and also it is in self-priming mud mono block pump. These are mainly used in loading mud/sewage, effluent etc.

Water PumpOur range of products include hydropneumatic booster system - hypn series, pressure booster pump - sh/scm series, lubi sewage submersible pumps, centrifugal water pumps, lubi vertical multistage pump and single shaft vertical multistage pump - ro series.

The pump volute casing shall be of cast Iron grade FG260 as per IS 210/ISO 186 with vertical discharge port suitable for pumping liquids upto 50 deg. C.The pumps shall have semi open impeller with material of construction of Cast Iron grade FG260 as per IS 210/ ISO 186.The pump shaft shall be made of stainless steel as per ASTM A582 and grade of AISI 410. The Pump shall be supplied with mechanical shaft seal with material of construction of Carbon/Ceramic/NBR/AISI 304.The pump shall be close coupled with dry submersible motor, having class F insulation, IP 68 protection, 2900 rpm, rubber sealed cable entry, with S1 duty for fully submerged and S3 duty for partially submerged, 1 phase, 240 volts, 3 phase, 415 volts.All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

Lubi Group of Industries, established in 1965, today Lubi employs 3500 People who are our strength, in Research & Development, Manufacturing Quality Assurance and Quality Sales. We are thus to achieve Annual Turnover of 120 Mio. USD company. The group is not only well placed in India but also has a wide presence in International Market. At present we are exporting our products to Middle East, North Africa and SE Asia including some 60Hz countries like Saudi Arabia, Korea & Philippines.

The LCR, LCRI, LCRN pumps are non-self-priming Pressure Booster Pump. The vertical in-line design enables the pump to be installed in a horizontal plane single system where the suction and discharge connections are in the same horizontal plane (in-line) and have the same pipe sizes. This design provides a more compact pump design saving space and easy pipe work. Pressure Booster Pump consists of a base and a pump head. The chamber stack and the outer sleeve are secured between the pump head and the base by means of tie bolts. All pumps are equipped with a maintenance-free mechanical shaft seal of the bellow type as standard. These pumps are available in various material versions according to the pumped liquid.

The pump volute casing shall be of cast Iron grade FG260 as per IS 210/ISO 186 with vertical discharge port suitable for pumping liquids upto 50 deg. C.

The pump shaft shall be made of stainless steel as per ASTM A582 and grade of AISI 410. The Pump shall be supplied with mechanical shaft seal with material of construction of Carbon/Ceramic/NBR/AISI 304.

The pump shall be close coupled with dry submersible motor, having class F insulation, IP 68 protection, 2900 rpm, rubber sealed cable entry, with S1 duty for fully submerged and S3 duty for partially submerged, 1 phase, 240 volts, 3 phase, 415 volts.

The pump casing shall have material of construction of Cast Iron FG 260 (standard supply), CF8, CF8M, axial suction and radial discharge port, dynamically balanced impeller, steel shaft, stainless steel shaft sleeve.

The pump shaft sealing will be by either gland packing or mechanical shaft seal suitable for 16 bar or 25 bar pressure rating based on shut off pressure of the pump.

The pump shall be close coupled with a totally enclosed fan cooled type (TEFC) Induction motor, with F class insulation, S1 duty and IP55 protection, suitable for 3 phase, 415 volts, 50 and 60 Hz power supply.

The pump shall have back pull out design so as to enable the rotating parts to be removed and serviced without dismantling the suction and discharge pipe work.

All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.Applications:The pump shall be designed for clear, clean liquids which are non-aggressive to the wetted parts and non-explosive, without any solids or fibers.

LVI pumps are non-self priming, single-stage, vertical in-line, close- coupled type centrifugal pumps having radial suction and radial discharge port. Vertical in line pump is designed for non explosive liquids which are clean, and thin without any solid particles. A viscous liquid affects the pump performance in the following ways.

We are providing our customers with a very high quality Crompton Greaves Selfpriming Dewatering Mud Pumps. They are manufactured using very high quality raw material procured from the reliable vendors of the industry. It is a cost effective product and is easily available to our clients. The product is manufactured under the surveillance of our expert professionals keeping in mind the latest market trends.

Lubi PumpsOffering you a complete choice of products which include end-suction centrifugal monoblock pumps, multi stage multi outlet fire pumps, horizontal split case fire pumpset, hpn pressure booster systems, lcrh series high-pressure vertical multistage centrifugal pumps and lubi long coupled end suction centrifugal pump.

The pump casing shall have material of construction of Cast Iron FG 260 (standard supply), Bronze LTB2, CF8, CF8M, axial suction and radial discharge port, dynamically balanced impeller, steel shaft, stainless steel shaft sleeve.

The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

The pump shall be close coupled with a totally enclosed fan cooled type (TEFC) Induction motor, with F class insulation, S1 duty and IP55 protection, suitable for 3 phase 415 volts, 1 phase, 230 volts power supply.

The pump shall have back pull out design so as to enable the rotating parts to be removed and serviced without dismantling the suction and discharge pipe work.

The pump casing shall have threaded ports near suction and delivery flanges for installing suction and discharge pressure gauges. The pump shall also have a threaded drain port at the bottom of casing for draining the pump during maintenance.

The pumps shall be non-self-priming, vertical multistage centrifugal pumps. The pump consists of a base and a pump head. The chamber stack and the outer sleeve are secured between the pump head and the base by means of tiebolts. The base has suction and discharge connections on the same level (in-line). All pumps shall be equipped with a maintenance-free mechanical shaft seal.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection, 3 phase, 415 volts, 1 phase, 230 volts, 50 and 60 Hz power supply.

The pump casing shall have material of construction of Cast Iron FG 260 (standard supply) or CF8 (AISI 304), inline suction and discharge port, closed type impeller, stainless steel shaft.

The pump suction and delivery flange connection shall be as per PN 16 standard up to 16 bar pump shut off pressure and as per PN25 for pumps with shut off pressure above 16 bar.

The pump shall be coupled with a Totally Enclosed Fan Cooled (TEFC) type induction motor, with F class insulation, S1 duty and IP55 protection, 3 phase, 415volts, 50 Hz and 60 Hz power supply.

The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection. 1 phase, 230 volts, 50 Hz (Standard Supply), 3 phase, 415 volts, 50 Hz.

A water detector is provided in the seal chamber. In case of seal failure if water enters the seal chamber, a signal can be sent to the control panel so that the pump operator is made aware of a potential seal leakage problem.

These pumps shall be available in Noryl or Polypropylene material of construction and closed coupled with standard TEFC motor. They are also available as long-coupled with standard TEFC as well as Flame Proof motor.

The pumps are made of non-metallic, glass-filled Polypropylene construction offering chemical resistance to most acids, alkalis, and inorganic solvents as does the Noryl series.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection. 1 phase, 230 volts, 50 Hz (Standard Supply), 3 phase, 415 volts, 50 Hz

The pump shall be designed for muddy water or liquids or effluents with solids or fibers. The liquid shall be compatible with material of construction of the pump.

Waste treatment: Pumping polluted, hot or corrosive waste water containing sand, mud or solids, in suspension, dosing neutralizing liquid, pumping out settled sludge.

The pump shall have back pull out design so as to enable the rotating parts to be removed and serviced without dismantling the suction and discharge pipe work.

In LCR The pump base and head cover shall be of Cast Iron grade FG 260 as per IS 210/ ISO 186 with inline suction and discharge connection. In LCRI the pump base shall be made of CF8 material, the pump head shall be of Cast Iron grade FG 260, pump head cover shall be of CF8M material. In LCRN The pump base and head cover shall be made of investment cast CF8M Stainless steel.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection, 3 phase, 415 volts, 1 phase, 230 volts, 50 and 60 Hz power supply