12-p-160 mud pump parts pdf made in china

PAGE DRAWING NO. REV. DRAWING DESCRIPTION 1 PL 1292332 C FLUID END ASSEMBLY (STANDARD) 2 PL 1292613 -- FLUID END ASSEMBLY WITH PREMIUM MODULES 3 PL 1292737 -- FLUID END ASSEMBLY WITH H.P. MODULES 4 PL 1292000 U FLUID END ASSEMBLY (SHEET 1 OF 3) WITH TAPR-LOK VALVE COVERS 5 PL 1292000 U FLUID END ASSEMBLY (SHEET 2 OF 3) TOP VIEW OF ROD CHAMBERS 6 PL 1292000 U FLUID END ASSEMBLY (SHEET 3 OF 3) SECTION THRU ROD CHAMBERS 7 PL 1292120 D LINER SPRAY SYSTEM 8 PL 1292001 X POWER END ASSEMBLY (SHEET 1 OF 3) SECTION THRU POWER END 9 PL 1292001 X POWER END ASSEMBLY (SHEET 2 OF 3) SECTION THRU CRANKSHAFT 10 PL 1292001 X POWER END ASSEMBLY (SHEET 3 OF 3) SECTION THRU PINION AND CROSSHEADS 11 -- -- SUCTION STABILIZER ASSEMBLIES (OPTIONAL) 12 PL 1292312 G DAMPENER MANIFOLD, DOUBLE SIDE INLET (OPTIONAL) 13 -- -- DAMPENER MANIFOLD ASSEMBLIES (OPTIONAL) 14 -- -- LINER FLUSHING SYSTEM (OPTIONAL) 15 PL 1292316 -- LINER FLUSHING SYSTEM, RIGHT ANGLE DRIVE (OPTIONAL) 16 PL 1291157 B LINER FLUSHING PUMP, RIGHT ANGLE DRIVE (OPTIONAL) 17 -- -- STRAINER CROSS ASSEMBLIES (OPTIONAL) 18 -- -- TOOL AND ACCESSORIES 19 PL 1292004 E OUTLINE DRAWING

NOV 12-P-160 Mud Pump is rated at 1600 input horsepower (1193 kw) at 120 strokes per minute, with a 12-inch (304.8 mm) stroke. Multiple liner sizes allow pressures and volumes to handle circulation requirements in deep drilling applications.

Flexibility: Compact engineering provides higher efficiency in less space. The NOV 12-P-160 Triplex Mud Pump light weight and flexible design make it easily adaptable to a variety of rig configurations. This provides flexibility as drilling requirements and conditions change.

Fluid End Modules: NOV offers a choice of fluid end modules and valve covers for every P Series pump model to select the fluid end module that exactly matches drilling requirements. All pump models can be equipped with either the standard or premium forged, two-piece interchangeable fluid modules

Lots of times it’s hard to find high quality aftermarket mud pump parts at a great value. And we know how difficult it can be to find all the right pump bearings and replacement parts in one site.

The good news is that in today’s world, you can find the right aftermarket mud pump supplies for a fraction of the OEM cost. Whether you’re looking for new parts for your 8-P-80, 9-P-100, 10-P-130, 12-P-160 or 14-P-220National style mud pumps, or any replacement brand mud pump, now at DrillingParts you can find ALL your high quality aftermarket mud pump parts in one place.

At DrillingParts, with one simple request, you will receive Multiple Quotes from various high quality Mud Pump Suppliers, all offering products that meet API standards.

There’s no need to waste time calling, emailing, texting and leaving messages for different suppliers. Let our marketplace Quote Request System easily find the right Mud Pump Parts for you.

Lake Petro provides high quality Mud Pump Parts including Mud Pump Liners, Mud Pump Fluid End Module, piston, Valve and Seat etc. With more than 10 years of experience in the oil and gas industry, we are dedicated to help and support our loyal clients with the most cost-effective and quality Liners and Pistons. We also provide mud pump price and mud pump for sale.

We offer Liners with Ceramic (Zirconia and Aluminium oxide) and Steel (Metal and Bi-metal) materials for all common brands of the mud pump and triplex mud pump.

All Lake Petro liner products are interchangeable with O.E.M. products. Meanwhile, we provide customized Liners according to drawings. Our liners, also with our other mud pump spares, are supplied for use in Honghua, F-Series, Bomco, Emsco and National lines of triplex drilling pumps. Let Lake Petro be your one-stop shop for your whole fleet of pumps. Please refer to “Suitable Pump Models” Lable for more details.

Drilling consumables such as mud pump systems and their components can drastically increase your uptime while reducing costs and health/safety/environmental (HSE) risks. To support your drilling needs, Forum’s patented P-Quip® mud pump system offers a single-source solution that integrates high-quality fluid end components for maximum longevity and performance.

With more than 20 years of successful operation in severe environments, P-Quip offers a proven track record for the lowest cost of ownership in the industry. As part of our commitment to quality, our mud pump parts use patented Banded Bore™ technology that significantly reduces stress concentrations and leads to longer module life.

Manufactured 1998, 1602 hours, 4" plungers with hydraulic charge pump, Detroit Series 50 (rebuilt), 5 speed, Skid mounted with fuel tank, Rebuilt expendables with seals, valves, seats, packings and gaskets.  Price:  $72,500

Complete without traction motors.  9” bore x 15” stroke, single acting, working pressure up to 7500 psi, (3) interchangeable forged steel fluid end modules with separate suction and discharge sections, Premium grade fluid end expendables with 6-1/2” pistons and liners, suction manifold with (3) 12” flanged inlets, SD8 suction desurger, pressure manifold with (2) 5-1/8” 10,000# API flanged outlets, liner wash system, 1 x 1-1/2” mission centrifugal pump p/b 3 hp electric motor, external power end lubrication pump, steel skid, suction line pressure relief valve, set of standard service tools  Price:  $675,000

CENTERLINE 7-1/2 X 10 MUD PUMP(Ref#14556Tb)  high pressure, no engine, needs retaining liner cage and (1) side suction manifold needs replacing, unmounted  Price:  $39,500

3 available in India. 1600 HP, rated pump speed 140 strokes per minute, maximum fluid cylinder liner bore 6-3/4", stroke 10", 10,000 PSI hydrostatic pressure of standard cylinder. 2.853 ratio of gears. 10" suction connection, 6" discharge connection. Valve pot mod .7., steel fluid ends, 5,000 psi pulsation dampener. Oilfield skid mounted. Performance Data: at 120 strokes per minute with 6-3/4" liners, pump will produce 4305 PSI and 574gpm. Set up for electric power. Dimensions and weight: 84,000 lbs, 209"L x 113"W x 75"H. Built 1976. Located India, removed from offshore drilling rig. Price: $75,000 each

approx. 7000 hours, Cat 3512C (1476 hp), 5000 psi fluid end cylinder, 5-1/2" piston cylinder, antifreeze heaters, WPT W21-CG-300 Type 1 PTO clutch, 16 grooove drive sheave, 16 groove bullwheel, 16 groove Kevlar belt with necessary guards, 5 x 6 x 11 charge pump c/w 50 hp@1200 rpm electric motor.  Discharge plumbing: 2" 5M XXH B/W Oteco gate valve, 4" 5M XXH b/w Oteco gate valve, 3" 5M Oteco popoff valve w/1502 connection, 2" 5M type D Oteco mud gauge with 1502 connection, Hydril 20 gal 5M pulsation damper.  Mounted on oilfield skid with separate, with expendables cabinet, knowledge box and removable engine skid for breaking the engine and pump into separate smaller loads.  Winterization package, oilfield lighting, explosion proof starters for charge pump, rod oiler pump and liner wash pumps.  Price:  $695,000 - Make Offer

Two Available, each complete with Cat 3508 diesel engines, pulsation dampener, and mud tanks with desander, desilter, etc.  Price for Package:  $110,000

Cat 3408 engine air start with pump drive and belt guard, PD55 Hydril dampener, 750 gallon fuel tank, mounted on heavy duty drop deck tandem trailer,  low hours  Price:  $87,500

14" stroke, 2" rod size, 400 hp, 75 strokes per minute, cast fluid ends, unitized on oilfield skid with Cat 3406 diesel engines, air start, new filters, oil and coolant, air receiver on deck, fluorescent lighting, drive belts with air clutch.  Gone over and in good operating condition, ready to be put into service.  Pumps currently have new 6" liners with production being 480 gpm @ 1000 psi.  All fluid end parts are brand new and never used, including the valves, gears, liners, pistons, rods, head gasket, and rod packing, equipped with pulsation dampener.  32" long x 11" wide x 7" high 50,000# weight

GARDNER DENVER TEE MUD PUMP(Ref#6440T)  New, unused, manufactured 2014, 4 available, bare pumps  Price:  $39,500 each  New Cat C7 engines available at additional cost

Pump only.  5" stroke, 300 hp, steel billet fluid end, 2-3/4" ceramic plungers, Delrim disc valves, 838 packing, 6" RF suction connection, 3" RTJ discharge connection, 231 gpm max, 2020 psi, max 360 rpm  Price:  $82,500

Two available, rebuilt, cast ductile iron fluid ends, used for oil service, bare pumps, no engines, unmounted, one is flanged for suction/discharge, one is threaded  Price:  $20,000 each

Cummins 150 hp reconditioned engine with snap-in clutch, 90 gal diesel tank with lock cap, Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ back up drill pipe bumper guard, front and rear loading hitches, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard Price: $82,500

Detroit 671 engine with Snap-In clutch (Gen Set approx. 1500 hours),  replaced fluid end parts with 4” liners,  mounted on 8’ x 12’ trailer with adjustable pintle and DOT lighting, 75 gal diesel tank with lock cap, Dayton oiler pump system and tank, 4” suction hose and winch boom, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard, 2’ x 2’ x 5’ lockable HD toolbox, mouting beams and steel/bolts  Price:  $41,500

8" x 17" base (mud boat), John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank, Dayton oiler pump system and tank, 4" suction hose and winch boom, 4" backup drill pipe bumper guard, front and rear loading hitches, 42" bull wheel with power band belt, belt guard  Price:  $99,000 PRICE REDUCED:  $73,500

750 hp, 8" stroke, 6" suction inlet, 4" discharge outlet, piston size 4-1/2" - 7",  max rod load 85,000#, approx. weight 11,500#, lubrication force fed, steel pump power end, double helical gears, 4.95:1 gear ratio, rod bearings sheel type replaceable, main bearings straight roler, pinion bearings spherical roller, crankshaft 1pc forged alloy steel, connecting rod knuckle joint, crosshead guide bronze replaceable, piston type fluid end Monoblock design, from high strength alloy steel, treated and sonic tested, Cat D379 diesel engine, 500 HP max linear bore size 3-1/2 - 6-1/4 x 7-3/4" stroke, test pressure 10,000 psi, gear ratio 2.742.8" suction line to 4 discharge stroke, location South America  Price:  $110,000

Two available, Skidded, Detroit Series 60 diesel engine DDEC V (475 hp), Allison 750 (6-speed) transmission with lock up control pane, Mission 4 x 5 centrifugal suction pump, 4” plungers, pulsation dampener, pressure gauge, safety valve, 10,000 psi fluid end, 5000 psi working pressure, NOV plug valve control manifold (4-valve) configured for 15k operation.  Can be configured to kill wells, acidize, cement, reverse circulate, drill out frac plugs or run in tandem.  Self-contained with fuel and fluid tanks and controls.  Steel canopy over skids, covered battery boxes, new batteries and disconnect switches.  Well maintained and in excellent condition.  Low hours on pumps and motors.  Ready to work.  Price:  $154,500 each

1600 hp, 12" stroke, 5000 psi, pulsation dampeners, pop off pressure release valve, pump pressure gauge, forged discharge manifold, overhead track for chain hoist, mounted on shipping skid, line washer pump, 6" liners, overall size:  192 x 128 x 105-3/4", inspection report available  Price:  $137,500

14 liter Detroit Diesel, 6061 Allison automatic transmission, rebuilt power end, new expendables in fluid end, new charge pump, skid, tanks, Pilfer 5 valve manifold, 15k fluid end, new paint  Price:  $215,000

Manufactured 1999, 1000 gal holding tank, (2) 3 x 4 Mission Magnum pumps with mechanical seals, MC255-2C mud cleaner, sand guzzler, Versa-drill rig jacks, Perkisn engine, spare hyd pump and filters, well maintained, ready to work  Price:  $59,500PRICE REDUCED: $49,500

Mounted on 12K GVRW trailer, hydraulic powered spool with approximately 500 of 2” hose, internally routed power and safety cable, 7.5 HP pump and motor, Whisper Watt 25kva 3-phase diesel generator with approx. 3100 hours  Price:  $45,000