centrifugal mud pump manufacturers in stock

Distributor of heavy duty submersible mud, sand, sludge & slurry pumps. Specifications of pumps include 5 hp to 30 hp motor, three phase, 208 V to 575 V, 6.8 A to 39 A, 3 in. to 6 in. NPT sizes, 38 ft. to 134 ft. head size & 475 gpm to 1,690 gpm flow rate. Features include impellers, wear plates & agitators made from abrasive resistant 28 percent chrome iron, process hardened ductile iron volutes casted with thick walls, class H motor insulation, double silicon carbide mechanical seals, heavy duty lip seal & stainless steel shaft & shaft sleeve. Sand, sludge & slurry pumps are used in mines, quarries, dredging, coal & ore slurries, sewage treatment plants & steel mills. UL listed. CSA approved. Meets OSHA standards.

Mud Pumps come in both electric and gas / diesel engine drive along with air motors. Most of these pumps for mud, trash and sludge or other high solids content liquid dewatering, honey wagon and pumper trucks. Slurry and mud pumps are often diaphragm type pumps but also include centrifugal trash and submersible non-clog styles.

WARNING: Do not use in explosive atmosphere or for pumping volatile flammable liquids. Do not throttle or restrict the discharge. Recommend short lengths of discharge hose since a diaphragm mud pump is a positive displacement type and they are not built with relief valves.

Continental Emsco Drilling Products, Inc., which consisted of Emsco drilling machinery and Wilson mobile rigs, was purchased by National-Oilwell, Inc on July 7, 1999. To our knowledge, no pumps have been manufactured and sold under the Emsco brand name since National-Oilwell acquired them.

Fairbanks Morse pumps are currently manufactured in Kansas City, Kansas. Fairbanks Morse is a division of Pentair ever since August, 1997 when Pentair purchased the General Signal Pump Group.

Gaso pumps are manufactured by National Oilwell Varco. Gaso was acquired as "Wheatley Gaso" by National-Oilwell in the year 2000. At the time, Wheatley Gaso was owned by Halliburton.

Skytop Brewster pumps are no longer available as new pumps. Skytop Brewster(Cnsld Gold), a unit of Hansen PLC"s Consolidated Gold Fields subsidiary, was acquired while in bankruptcy by National-Oilwell, Inc. in November, 1999.

Power Zone is a leading global supplier of new, used and reconditioned pumps for sale. Our inventory of pumps includes multi-stage centrifugal pumps, positive displacement pumps, reciprocating pumps, single stage centrifugal pumps and screw pumps in a variety of design standards including API 610 Centrifugal Pumps, API 674 Reciprocating Pumps and API 676 Rotary Pumps. We have an assortment of pumps that are used in various applications including water treatment, pipelines, frac water supply, salt water disposal and flood control in industries like municipal, manufacturing, oil & gas, mining and agriculture. We supply pumps of all major suppliers such as Sulzer, Flowserve, ITT Goulds, Aurora and National.

American Mfg Company is a quality manufacturer of replacement parts for the wide variety of mud pumps, centrifugal pumps, rig parts, and swivel parts found on the World market today.

American Mfg Company Pumps And Parts carry over $5,000,000 of interchangeable mud pumps parts, centrifugal pump parts, rig parts and swivel parts in stock for all major manufacturers such as Gardner Denver, Failing, Wheatley, National, Emsco, Ideco and Opi, as well as OE AM pumps.

Centrifugal Pumps - Unused Surplus Flowserve 3x8-7 stage DMX centrifugal pump. CF3MN case material • 7-stage • 4” 600# RF suction flange • 3” 900# RF discharge flange • Mechanica... More Info

Centrifugal Pumps - Unused Surplus Flowserve 4HPX13A, API 610, OH2 pump. 952 gpm, 448 tdh, 3575 rpm with a unused surplus Siemens 200 HP electric motor with following features: 3575 rpm, 46... More Info

Centrifugal Pumps - Unused Surplus Flowserve 6HED16DS, API 610, OH2 pump. 1850 gpm, 990 tdh, 3575 rpm with a unused surplus Reliance 600 HP electric motor with following features: 3579 rpm,... More Info

Centrifugal Pumps - Unused Surplus Flowserve 6HED25DS 10 x 6 single stage API-610 centrifugal pump, 10" 600lb suction, 6" 600lb discharge, CA6NM case material. Tag reads 1327 gpm, 430 tdh, 1... More Info

Centrifugal Pumps - Unused Surplus Flowserve 6HPX23A, API 610, OH2 pump. 2917 gpm, 480 tdh, 1785 rpm with a unused surplus Teco Westinghouse 600 HP electric motor with following features: ... More Info

Centrifugal Pumps - UNUSED SURPLUS FLOWSERVE 6UZDL25 CENTRIFUGAL PUMPS WITH MOTORS. TAG READS 2,879.48 GPM, 945.86 HEAD FEET, SP. GRAVITY 0.97, HORSEPOWER 921, 1783 RPM, CUSTOMER ORDER NUMBE... More Info

Centrifugal Pumps - For Sale: Qty (1) Unused Surplus Flowserve 6x11 DMX-A 7 stage centrifugal pump. CA6NMB case material, 11.18" CA6NM impeller. Tag reads 1800 GPM, 2762 TDH, 3560 RPM. More Info

Centrifugal Pumps - Unused Surplus Flowserve 8HDX27B single stage centrifugal pump, tag reads 1794 rpm, 3412 gpm, 649 tdh, S.G .968, C6 API 610 / 12 Chrome case material. API 610 BB2 Class P... More Info

Centrifugal Pumps - Used Flowserve VTC 42 KXH Vertical Turbine Pump Only. Size 42-3 stage, CA6NM bowls, 316 stainless column and head. 27"- 9" long. Tag reads 20693 gpm, 406 tdh, 710 rpm. More Info

Centrifugal Pumps - Gardner Denver PAH equipped with 5-inch pistons and liners, powered by Caterpillar C10 diesel engine with Allison automatic transmission. With clutch manifold and centrif... More Info

Centrifugal Pumps - Unused Surplus Goulds 3700 1.5x3-9N, API 610, OH2 pump with the following features: • 316SS case material • 1-stage • 316SS impellers • 3” 300# RF suction flang... More Info

Centrifugal Pumps - Unused Surplus Goulds 3700 6x8-13A, API 610, OH2 pump with the following features: 316SS case material, 1-stage, 316SS impellers, 8” 300# RF suction flange, 6” ... More Info

Centrifugal Pumps - Goulds LF3196 Centrifugal Pump, Pumps & Parts, Used Goulds LF3196 Centrifugal Pump, Impeller Diameter 7.875, 37 GPM, 3600 RPM, 312" TDH Head, 1x1.50-8 National Constructi... More Info

Centrifugal Pumps - Grundfos CR1017, Pumps & Parts, New Grundfos CR10-17 Centrifugal Pump 638" TDH Head, 53 GPM, 3444 RPM, 60 Hz, Type CR10-17 A-GJ-A-E-HQQE, Driven by Baldor 15hp Electric M... More Info

Centrifugal Pumps - Grundfos CR16 30, Pumps & Parts, Used Grundfos CR16-30 U-G-A-AUUEV Vertical Centrifugal Pump, Model B33000063VP1 0112 US432, 84 Gallons/Minute, 169FT-TDH, 3450 RPM, 7.5HP... More Info

Centrifugal Pumps - Grundfos CR16 30, Pumps & Parts, Used Grundfos CR16-30 U-G-A-AUUEV Vertical Centrifugal Pump, Model B 33000063VP1 0112 US 336, 84 Gallons/Minute, 169FT-TD, 3450 RPM, 7.5H... More Info

Centrifugal Pumps - Halco 3 x 4 Centrifugal Pump, Pumps & Parts, Used Halco 3 x 4 Centrifugal Pump, Size 3 x 4 x 13, Model # 1780, Steel Volute, Takes Packing , More Info

Centrifugal Pumps - Ingersol Rand 2.5 CNTA-4 centrifugal pump with the following features: Carbon steel case material, 4 stages, 9.375"" Bronze Impellers, 4" 300# suction flange, 2.5" 300# d... More Info

Centrifugal Pumps - Used KSB HGC 5/7 Centrifugal Pumps. Chrome Case Material, 7 Stage, 8" 300# RF Suction, 6" 1500# Discharge. Tag Reads 1992 GPM, 2082 PSI, 3582 RPM. More Info

We are the original designers and manufacturers of the MudMaster MM420DT and MM435DT mud pumps. For over 35 years, we have built and supported the best pump packages in the industry. With over 1,000 units in service, you are assured of a quality product and after-sales support.

Standard build includes TEFC motor. “Explosion proof” motors are also available. This belt driven unit is easily adjusted and permanently aligned. The triplex piston type pump is simple, rugged and reliable. 50 Hz or 60 Hz motors are available at any common three-phase voltage input. A preset, adjustable pressure relief valve is standard equipment.

Rating is 25 US gpm (95 L) with disc type valves or 20 US gpm (76 L) with ball valves. Disc valves are intended for use with clean fluids and ball valves are suited to drilling mud solutions. The pumps are available with optional materials of construction to suit special applications.

A centrifugal pump has a relatively straightforward design: a casing with a discharge valve houses an impeller with multiple blades which turns on a mechanically powered rotating shaft. As the shaft rotates, this pumping motion increases the pressure of the liquid passing through the casing via kinetic energy generated by the blades on the impeller. Once the fluid"s pressure is increased, it passes through the pump through the discharge valve. Centrifugal force is combined with positive displacement to sustain the operation.

This basic design allows pumps to be installed in larger mechanical systems or engines, from automotive engines to water treatment plants. Because centrifugal pumps often work with a variety of different fluids, from water to acids to oil, the casings are usually made from fairly hardy materials such as stainless steel, cast iron, or aluminum. The pumps usually have a weep hole, which is an opening on the underside of the pump that is used to help spot the first signs of mechanical seal failure. The mechanical seal is used to create a barrier between the motor and the water so that unwanted fluid does not go into the engine or motor. When the weep hole leaks, the pump will probably need repair or replacement.

High pressure or an overabundance of oxygen, specifically pockets of air within the casing that can develop when the pump is not being used and the casing is empty, can disrupt the operation of centrifugal pumps. Many pumps need to be regularly primed or checked for air pockets to ensure a seamless operation. The formation of air pockets is frequently referred to as cavitation.

The earliest conceptual incarnation of the centrifugal pump originated during the Italian Renaissance thanks to an engineer known as Francesco di Giorgio Martini, who described a mud lifting machine in a treatise in 1475. The more modern and recognizable form of the pump, with its straight vanes, did not appear until Denis Papin designed it during the 17th century. However, it wasn’t until the 19th century that the next major advance in the field was made. In 1851, John Appold unveiled his design for a centrifugal pump with a curved vane, which won him a council medal at that year’s Great Exhibition at the Crystal Palace. The curved vane was three times as efficient as any of the preexisting straight vane pumps, and had a profound influence on the industry.

While all centrifugal pumps use positive displacement as part of their operating procedure, they are differentiated from positive displacement pumps by the fact that they also increase the speed of the liquid moving through the pump, while positive displacement pumps simply move the liquid at the same speed. Positive displacement pumps include a lobe, screw, peristaltic, and a gear pump configuration.

A gear pump creates positive displacement by way of multiple meshing gears. There are two main types of gear pumps, internal and external. An internal gear pump uses a combination of an internal and external gear spur, while an external pump uses two external gear spurs. The fluid processed by these pumps moves at a steady rate per each revolution. Gear pumps are most frequently used in hydraulic fluid power operations.

Most vehicles built in the United States during the 20th century use a centrifugal water pump to provide water to the engine. The impeller of the water pump can sometimes be modified to increase the flow rate of the pump and the subsequent performance of the engine.

In fact, most centrifugal pumps differentiate themselves by modifying either the impeller or the discharge apparatus. The curvature and depth of the impeller vanes or blades has a significant impact on the operation of the pump. The impeller itself can also either be left open or closed. In a closed situation, a plate or other enclosure is affixed to the impeller blades. This has been shown to increase the flow rate in some applications, depending upon the specific fluid that the pump is processing.

The size of the discharge apparatus, combined with the speed of the shaft, can also significantly impact flow rate. However, it is vital that any modification of a pump does not unduly increase the “head” or pressure within the system. This pressure is measured in pounds per inch, or PSI, and refers to the force exerted by the fluid within the pump.

Have a vertical shaft attached to a perpendicular impeller. The lifting action of the impeller vanes pushes the liquid within the pump upwards in an axial flow pump. A jet pump aids the operation of a centrifugal pump by increasing suction, while a submersible pump is installed underground. True to its name, a submersible pump is almost constantly inundated with liquid, and therefore is a self-priming pump: air pockets rarely form within the suction line because water or another liquid is always being circulated through the pump.

While most pumps are powered mechanically, some pumps are powered by a hydraulic motor. Submersible pumps can be powered electrically. The power cords to these pumps are encased in a durable, waterproof cover, usually layered with thick rubber. Because they are more difficult to maintain, electric pumps tend to be smaller, such as a 12 volt pump, and deployed for specific operations, such as pumping out a flooded structure. The pump can be placed on a floating rig with an outbound discharge hose and allowed to gradually pump out the unneeded water. These pumps are sometimes also referred to as sump pumps.

Designed to work with abrasive fluids, including bleach, resin, acid, and an array of other toxic, often corrosive, materials. These can be useful in industrial operations. Well pumps, meanwhile, pump water from an underground region to a higher location within a given structure. Well pumps are often used to provide water for apartment buildings or other large structures, and often work in concert with a pressure tank.

Although they are primarily designed to deal with liquid, the centrifugal pumps can occasionally handle liquids that are contaminated with other materials, such as twigs, small rocks or sand, or other debris. These types of pumps are known as trash pumps, and are generally used in wastewater treatment plants or sewage operations. A trash pump is typically able to pump thousands of gallons of water per minute, a measurement that is referred to as the flow rate, and manages the thicker, more viscous liquid by way of a very large discharge opening and much deeper impeller vanes than are found on a typical centrifugal pump. There are several different subsets of trash pumps, including semi-trash pumps, and other pumps that handle liquids with specific particulate size limits. A dewatering pump, for example, can process non-hazardous water with particulate matter up to 0.25” in diameter. Some dewatering pumps are completely submersible and can operate from any position, including upside down.

A type of radial flow pump in which the fluid enters the impeller from both sides. Due to the extending of the shaft into the suction passage, double suction pumps are limited to pumping clear liquids.

Designed with wide unblocked passageways and are an intermediate pump between radial and axial flow pumps. Mixed flow pumps develop the pressure partially with centrifugal force and partially with the lift of the impeller vanes on the liquid.

Can be either horizontal or vertical, consist of two or more pumps of similar capacity that discharge into each other in a series. Progressively the pumps develop a total head, the sum of the heads that each pump has developed. A common shaft with several impellers, each with its own volute, is rotated by a power supply, building up pressure in stages.

Take in liquid through the center of the impeller and move it out along the impeller blades at a 90-degree angle to the pump shaft. Radial flow pumps develop the pressure only with centrifugal force.

A type of radial flow pump in which the fluid enters the impeller from one side, and the shaft does not reach into the suction passage. Single-end suction pumps are used in applications where there are large solids, such as rags and trash, that would normally clog the pump.

Designed to have only the casing and the impeller submerged in the pumpage for priming and the support bearings for the rotating element in a dry environment.

Have no throttle or bumper bushings or any rings at the impeller or submerged below the maximum normal water level, and they are used in applications, such as a sump or tank, in which it is necessary not to have a bearing in the pumpage.

Inefficiently designed pumps in which the impeller is recessed into the volute. However, vortex pumps are practical in applications that require pumping of excessive solids.

While a certain threshold of increased pressure is needed to make the pump operate successfully, too much head can unbalance the pump, causing damage. Depending on the amount of pressure, a pump can occasionally tear free from its moorings, known as shock mounts, and wreak havoc on an engine or surrounding assemblies. In order to avoid this unfortunate circumstance, pump owners should regularly prime their pumps to avoid cavitation, and make sure that they are not attempting to force too much liquid through their system too quickly. Operating a pump with a motor that is moving too quickly can also result in a build-up of unwanted head, thereby damaging the pump.

Frequent cavitation also damages the components within the pump. This happens because the impeller blades become pitted when the air pockets explode under pressure. Priming the pump at regular intervals will prevent undue cavitation, although over the working lifetime of a pump some amount of cavitation is likely to occur.

Because of their wide range of applications, centrifugal pumps are manufactured by a number of different companies for different purposes. Generally speaking, the pumps will increase in size and power for heavier industrial applications, while smaller pumps are used for less intensive operations. The industrial centrifugal pump manufacturing market has created pumps with 40,000 gallon per minute flow rates. This flow rate would not be necessary in a smaller application, such as in a car or in a well pump in a single family home.

Manufacturers are also experimenting with the use of thermoplastics and fluorocarbons as opposed to metal for use in the seals of pumps. These types of materials tend to resist corrosion better than metal, and therefore can increase the longevity of the pump without compromising the production of kinetic energy or centrifugal force. However, the use of stainless steel, cast iron, and aluminum is still typical for the exterior casings, although plastic is occasionally suitable as a material.

The need for jet pumps has also decreased in recent years as manufacturers have become more adept at designing pumps that provide ample suction without the need for additional assistance. However, depending on the viscosity of the fluid and any corresponding debris, a jet pump may still be needed.

In any case, a client who is attempting to find the best manufacturer for their needs should first be able to specifically articulate the application for which they will be using the pump. A client who is attempting to install a series of drainage pumps across a wide variety of low-lying properties will have different needs than a client who wishes to operate an aftermarket parts company that will sell modified water pumps for higher automotive engine performance. Similarly, it is vital that the client understands the kind of fluid they will be dealing with and its relative purity. In the case of the client who is seeking a manufacturer for drainage pumps, the water that the pumps will encounter will likely have some form of debris or small particulate matter contained within it. The aftermarket parts company, on the other hand, will likely be dealing with relatively clean water that has little to no debris. In each case, the condition of the liquid will influence what kind of pump is appropriate for the task.

Many manufacturers prefer to produce “mill runs” or large batches of a given product. This is partially because a large production batch will decrease overhead costs while also guaranteeing a substantial sum for the company. Clients who are attempting to design a new version of a pump or improve upon the basic centrifugal pump design should first make prototypes of the design. These prototypes will enable the client to instigate a thorough round of testing, which will reveal any flaws or unexpected performance quirks of the pump before it is approved for mass production. Manufacturers are often able to recommend a machinist or other fabricator for this task if they do not have a department already dedicated specifically to prototype production.

The force applied by the atmosphere to the surface of the earth. Atmospheric pressure, the standard of which is 14.7 lbs per square inch, affects the operation of a pump.

An undesirable condition in which vacuum pockets form within the pump. The air pockets eventually implode under pressure, resulting in the pitting of the impeller and volute surfaces.

An apparatus in a discharge or suction line that permits flow in only one direction so as to prevent reverse flow and isolate the material being pumped.

A stationary casing, like a volute, that houses the moving impeller. Diffusers are compact in design, enabling the pump to create higher pressure heads.

The required amount of gallons per minute (gpm) of pump flow. Flow can also be expressed in gallons per hour (gph) and in million gallons per day (mdg).

A rotating disk with vanes of varying amounts attached to the “r” drive shaft that creates centrifugal force within the pump casing of a centrifugal pump. Impellers can be open or closed.

Pump components located on the impeller between the eye and the discharge side of the impeller. Impeller vanes direct the flow of the liquid to the outside diameter of the impeller.

Allowing the pump to disperse all air from the influent line of a circulating system by causing fluid to start flowing once again. Priming the pump is usually accomplished by either manually filing the volute or turning the pump on.

Stationary casing of a centrifugal pump that separates air and water and in which the impeller rotates. Volutes are spiral-shaped in order to facilitate the partial conversion of the velocity (kinetic) energy into pressure head as the water leaves the impeller.

A small opening located on the underside of the pump at which point the engine joins the pump. Weep holes provide the means to quick detection of a leak before water seeps into the oil sump of the engine.

Standard Industrial Manufacturing started in 1979. Our mission was to manufacture and supply pump parts to a few select pump retailers and OEMs. During the 1980s the company expanded its customer base to include all pump retailers and OEMs. Today, Standard has broadened its product lines to include most fluid-end expendables for all major pump brands.

Mission Magnum 8x6x14 Centrifugal Pumps are used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid.

The revolutionary design of the MAGNUM I provides supreme-duty performance in all types of fluid pumping operations. Although it offers greater capacity and higher heads, the MAGNUM I remains the competitive pump of choice for aggressive applications.

The Magnum has an open impeller design that contains wide-tipped vanes and a more tangential circumference of the suction allowing the pump to create a smoother flow pattern when handling abrasive fluids. The Magnum is available in Magnachrome™, hard iron, stainless steel, and aluminum bronze fluid ends. The pumps can be unitized with electric motors, diesel engines, and hydraulic motors (horizontal, vertical, or close-coupled configuration).

According to the different working conditions, Mission centrifugal pumps can be used as Frac discharge pump, Frac suction pump, Oil drilling centrifugal pump, electric centrifugal transfer pump, Skid mounted mixing pump, Transfer pump, Trash pump, Grinding pump, Circulating mud pump, Centrifugal sludge pump, Drilling fluid centrifugal pump, Horizontal directional drilling pump, Denver pump, Filling pump, Feeding pump, etc

Having a quality mud pump is a critical part of keeping your oil well drilling system running as smoothly as possible. Dragon carries a wide range of mud pumps for systems of all kinds and jobs of all sizes. We also carry a 50 BPM mud mixing table to make drilling fluid mixing more efficient and accurate so you can always get the job done safely and correctly. View our full well service pump and mud pump selection to find the right system for your job site, or check out the rest of our drilling rigs for even more options.

The global centrifugal pump market attained a value of nearly USD 1.04 billion in 2021. The market is estimated to grow in the forecast period of 2023-2028 at a CAGR of 5.8% to reach about USD 1.38 billion by 2027.

The Asia Pacific region is expected to witness significant growth in the centrifugal pump market due to the economic expansion in countries like China, Japan, India, South Korea, Australia, and Singapore, among others. The increasing attraction of investors for the production and manufacturing of centrifugal pumps due to the availability of raw materials, cheap labour, and strong economic case for channelling capital flows in emerging economies is also driving the market growth of the region. The surging investment in R&D activities and growing industrial activities in the region owing to the support of local governments and low manufacturing costs are further expected to fuel the market growth of centrifugal pump in the Asia Pacific region. With the increasing demand for centrifugal pump in various end-use industries and market expansion strategies by pump manufacturers in the region, the market for centrifugal pumps is expected to propel over the coming years in the region, which is likely to significantly contribute to the overall market’s expansion in the forecast period.

A centrifugal pump refers to a hydraulic machine that enables the conversion of mechanical energy into hydraulic energy using centrifugal force acting on the fluid. The main purpose of a centrifugal pump is to transfer fluids through an increase in pressure. Centrifugal pumps can have various structures, but their operating principle and fluid dynamic characteristics are constantly the same.

The EMR report looks into the regional markets of centrifugal pump like Latin America, North America, Europe, the Asia Pacific, and the Middle East and Africa.

Based on end-user, the rise in the waste and wastewater segment is expected to bolster the growth of the centrifugal pump market during the forecast period on account of the surging investment in infrastructure development activities, coupled with the increasing development of wastewater plants. Rapid industrialisation and the rising demand for centrifugal pumps by municipalities in various applications are expected to propel the market demand for centrifugal pumps across the globe over the upcoming years. Moreover, the introduction of various favourable government initiatives to boost industrialisation, the surging product demand from the wastewater treatment industry, and the integration of IoT sensors in centrifugal pumps, are further anticipated to bolster the market growth of centrifugal pump in the forecast period.

The report presents a detailed analysis of the following key players in the global centrifugal pump market, looking into their capacity, market shares, and latest developments like capacity expansions, plant turnarounds, and mergers and acquisitions: