drilling mud pump rentals brands

Having a quality mud pump is a critical part of keeping your oil well drilling system running as smoothly as possible. Dragon carries a wide range of mud pumps for systems of all kinds and jobs of all sizes. We also carry a 50 BPM mud mixing table to make drilling fluid mixing more efficient and accurate so you can always get the job done safely and correctly. View our full well service pump and mud pump selection to find the right system for your job site, or check out the rest of our drilling rigs for even more options.

Please reach us for any specific or hard to find or if you have a tight budget for your drilling program we would be glad to help provide a reasonable and reliable solution.

The Baoji/Bomco F1000 Triplex mud pump has a max. working pressure of 5,000PSI and a 6-3/4" liner size. This model is the first choice for the medium and deep dr... More Info

The Baoji/Bomco F1600HL Triplex mud pump has a max. working pressure of 7,5000PSI and a displacement of 46.5L/S with 6" liner size. This model is the f... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Emsco/Bomco 1600 Mud Pump, Unitized 1600 Mud Pump Powered by Two GE 752 Motors Charging Pump, Liner Flush Pump, Relief Valve, Mud Gauge, Etc. ....Call For Price More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud Pumps - 1 - Rebuilt Gardner Denver PZ-9 Mud Pump Package, New Caterpillar C-27, 1050 HP diesel engine. Belt-driven. comes with pulsation dampener, discharge block, precharge, li... More Info

Mud Pumps - 1 of 3 used Gardner Denver PZ-8 triplex mud pumps. This would be a good rebuildable core. We also have new, rebuilt and good used pumps and packages available for sale ... More Info

Mud Pumps - Mud Pump Parts & Complete Units: Liners, Pistons, Rubbers, Rods, Valves, Seats, Springs, Inserts (Bean, BJ, CAT, EMSCO, Ellis Williams, FMC, Failing, GASO, Gardner Denver... More Info

Mud pumps are the heart of your drilling operation. Bridges Equipment is the leading authority on the unitization of triplex mud pumps. As an OEM distributor for Caterpillar Rig Power, Detroit Diesel, and Joliet motors, we provide our customers with a wide range of options to meet their pump needs.

A malfunctioning mud pump can throw an entire drilling operation off schedule. Our fleet of mud pump packages are available to rent while the broken unit is being repaired, so your drilling operation never misses a beat.

Our Gardner Denver, RSF, and Continental Emsco triplex pump packages range from 500-1600 HP and can be fully customized to suit your project. Contracts are offered for as few as 10 days, so whether you need to replace a broken unit or need a long-term rental to act as a backup pump, we’ve got you covered.

MTI is a full-service company providing equipment, parts, and service to the oilfield, HDD (Horizontal Directional Drilling), geothermal, mining and water well drilling industries.

We manufacture a complete line of solids control equipment including; mud reclaimers & mud recyclers, shale shakers, de-silters, de-sanders, and pump packages, all for sale or for rent, allowing us to achieve a higher standard of excellence.

A large inventory of parts and accessories , and knowledgeable staff makes Mud Technology the smart choice for operators needing fast-turnaround times and competitive pricing.

Our staff is available to assist you with complete line of parts, including pump parts, shaker screens and drilling mud all available at competitive prices. As we are just a phone call away, we are available to answer questions and assist you with troubleshooting while you are in the field.

C-MOR Energy Services offers competitive discount pricing on rental equipment for partial, semi-full and full rig rental packages. All of our equipment is inspected monthly and repaired as needed. We are a full-service rental and service company that has a presence in almost every major oil basin in the world. C-MOR Energy Services has oil drilling rig rental equipment available so that your operation never slows and absolutely never stops. We have everything you’ll need, like BHA racks, bit houses, catch tanks, drive overs, flare boxes and lines, hose houses, mud trailers, and more. We understand the needs of the oil field companies and workers, so we stay ahead of them and keep everything in stock and ready to go at all times. We are able to build and fabricate custom oilfield equipment, and there is no project too big or small. Come to us first for all your oil drilling rig rental equipment needs.

The drilling industry has roots dating back to the Han Dynasty in China. Improvements in rig power and equipment design have allowed for many advances in the way crude oil and natural gas are extracted from the ground. Diesel/electric oil drilling rigs can now drill wells more than 4 miles in depth. Drilling fluid, also called drilling mud, is used to help transfer the dirt or drill cuttings from the action of the drilling bit back to the surface for disposal. Drill cuttings can vary in shape and size depending on the formation or design of the drill bit used in the process.

Watch the video below to see how the EDDY Pump outperforms traditional pumps when it comes to high solids and high viscosity materials commonly found on oil rigs.

Solids control equipment including shakers, hydro-cyclones, and centrifuges are utilized to clean the drill cuttings from the drilling fluid, which then allows it to be reused and recirculated. The circuit includes the mixing of the drilling fluid in the rig tanks.

The drilling fluid is prepared to control fluid loss to the formation by the addition of chemicals or mineral agents. Commercial barite or other weighting agents are added to control the hydrostatic pressure exuded on the bottom of the well which controls formation pressures preventing fluid or gas intrusion into the wellbore.

The fluid is charged into high-pressure mud pumps which pump the drilling mud down the drill string and out through the bit nozzles cleaning the hole and lubricating the drill bit so the bit can cut efficiently through the formation. The bit is cooled by the fluid and moves up the space between the pipe and the hole which is called the annulus. The fluid imparts a thin, tough layer on the inside of the hole to protect against fluid loss which can cause differential sticking.

The fluid rises through the blowout preventers and down the flowline to the shale shakers. Shale shakers are equipped with fine screens that separate drill cutting particles as fine as 50-74 microns. Table salt is around 100 microns, so these are fine cuttings that are deposited into the half-round or cuttings catch tank. The drilling fluid is further cleaned with the hydro-cyclones and centrifuges and is pumped back to the mixing area of the mud tanks where the process repeats.

The drill cuttings contain a layer of drilling fluid on the surface of the cuttings. As the size of the drill cuttings gets smaller the surface area expands exponentially which can cause rheological property problems with the fluid. The fluid will dehydrate and may become too thick or viscous to pump so solids control and dilution are important to the entire drilling process.

One of the most expensive and troubling issues with drilling operations is the handling, processing, and circulation of drilling mud along with disposing of the unwanted drill cuttings. The drilling cuttings deposited in the half round tank and are typically removed with an excavator that must move the contents of the waste bin or roll-off box. The excavators are usually rented for this duty and the equipment charges can range from $200-300/day. Add in the cost for the day and night manpower and the real cost for a single excavator can be as much as $1800/day.

Offshore drilling rigs follow a similar process in which the mud is loaded into empty drums and held on the oil platform. When a certain number of filled drums is met, the drums are then loaded onto barges or vessels which take the drilling mud to the shore to unload and dispose of.

Oil field drilling operations produce a tremendous volume of drill cuttings that need both removal and management. In most cases, the site managers also need to separate the cuttings from the drilling fluids so they can reuse the fluids. Storing the cuttings provides a free source of stable fill material for finished wells, while other companies choose to send them off to specialty landfills. Regardless of the final destination or use for the cuttings, drilling and dredging operations must have the right high solids slurry pumps to move them for transport, storage, or on-site processing. Exploring the differences in the various drilling fluids, cutting complications, and processing options will reveal why the EDDY Pump is the best fit for the job.

The Eddy Pump is designed to move slurry with solid content as high as 70-80 % depending on the material. This is an ideal application for pumping drill cuttings. Drill cuttings from the primary shakers are typically 50% solids and 50% liquids. The Eddy Pump moves these fluids efficiently and because of the large volute chamber and the design of the geometric rotor, there is very little wear on the pump, ensuring long life and greatly reduced maintenance cost for the lifetime of the pump.

plumbed to sweep the bottom of the collection tank and the pump is recessed into a sump allowing for a relatively clean tank when the solids are removed. The Eddy Pump is sized to load a roll-off box in 10-12 minutes. The benefit is cuttings handling is quicker, easier, safer, and allows for pre-planning loading where the labor of the solids control technician is not monopolized by loading cuttings. Here, in the below image, we’re loading 4 waste roll-off bins which will allow the safe removal of cuttings without fear of the half-round catch tank running over.

Mud cleaning systems such as mud shaker pumps and bentonite slurry pumps move the material over screens and through dryers and centrifuges to retrieve even the finest bits of stone and silt. However, the pump operators must still get the raw slurry to the drill cuttings treatment area with a power main pump. Slurry pumps designed around the power of an Eddy current offer the best performance for transferring cuttings throughout a treatment system.

Options vary depending on whether the company plans to handle drill cuttings treatment on-site or transport the materials to a remote landfill or processing facility. If the plan is to deposit the cuttings in a landfill or a long-term storage container, it’s best to invest in a pump capable of depositing the material directly into transport vehicles. Most dredging operations rely on multiple expensive vacuum trucks, secondary pumps, and extra pieces of equipment.

Using an EDDY Pump will allow a project to eliminate the need for excavators/operators to load drill cuttings, substantially lowering both labor and heavy equipment costs. The EDDY Pump also allows a company to eliminate vacuum trucks once used for cleaning the mud system for displacing fluids. Since the pump transfers muds of all types at constant pressure and velocity throughout a system of practically any size, there’s little need for extra equipment for manual transfer or clean up on the dredge site.

The EDDY Pump can fill up a truck in only 10 minutes (compared to an hour) by using a mechanical means such as an excavator. For this reason, most companies can afford one piece of equipment that can replace half a dozen other units.

This application for the Eddy Pump has the potential to revolutionize the drilling industry. Moving the excavator out of the “back yard” (the area behind the rig from the living quarters) will make cuttings handling a breeze. Trucking can be easier scheduled during daylight hours saving on overtime and incidences of fatigued driving. Rig-site forklifts can move the roll-off boxes out of the staging area and into the pump loading area. The operator can save money on excavators rental, damages, and keep the technician operating the solids control equipment.

The EDDY Pump is ideal for drilling mud pump applications and can be connected directly onto the drilling rigs to pump the drilling mud at distances over a mile for disposal. This eliminates the need for costly vacuum trucks and also the manpower needed to mechanically move the drilling mud. The reasons why the EDDY Pump is capable of moving the drilling mud is due to the hydrodynamic principle that the pump creates, which is similar to the EDDY current of a tornado. This tornado motion allows for the higher viscosity and specific gravity pumping ability. This along with the large tolerance between the volute and the rotor allows for large objects like rock cuttings to pass through the pump without obstruction. The large tolerance of the EDDY Pump also enables the pump to last many times longer than centrifugal pumps without the need for extended downtime or replacement parts. The EDDY Pump is the lowest total life cycle pump on the market.

Tanks for capture, storage and disposal of different wellsite fluids and solids are an essential part of any fluid management program. Wellsite operations employ a wide variety of tanks for drilling fluids, solids control, completion fluids and production chemicals.

At Panther, we manage the operations of wellsite drilling fluids, including the handling of liquids and solids in one of our newly-designed open-top tanks. We select tanks based on the application and project but will also work with you to provide the right tank for any job.

The drop-down menu below lists the items we usually have in-stock. All of them are also normally available for sale or for rent. Rental products also include additional systems such as Triplex Mud Pumps (Diesel or Electric), Mud Tanks and Solids Control Equipment. For fast and easy equipment request, we have provided online forms customized to each specific area of interest. The photos below illustrate just a few of the items available in our inventory. View our current published inventory at tradequip.com.

Cutting down on capital costs is an effective way to compete in the market with lesser exposure to risks. Watersintl offers flagship models of drilling equipment for rent to help ease the burden of heavy investments. Rental of drilling equipment helps companies to add the latest equipment to their operations at considerably lesser costs. At Watersintl, we offer unmatched and unrivalled terms of rental. Drilling equipment are pivotal to operations and as specialists, we at Watersintl understand the need for quality and reliability. Our team of technicians ensure that every unit of drilling equipment offered on rental meets our benchmarked criteria of rugged operational capability.

Rental of drilling equipment offers agencies the options of taking up specialized tasks and contracts without having to shoulder the burden of oversized inventory and depreciation. At Watersintl, our extensive and robust network lends us the ability to offer the best equipment for rental. Our standards will remain the same, uncompromising on quality and commitment.With terms and convenient interfaces available for browsing through categories of equipment, you will find all that you need right here. The list of equipment available for rent with us are more of an inventory that is coveted by drilling contractors.

For over 40 years, the Tasman group have been a leading industry expert in the oil and gas drilling equipment rental sector. We are renowned for our reliability, responsiveness, flexibility and superior service delivery. Our hallmark and trademark is excellence in all things and we settle for nothing less. We aim to keep our clients happy by providing them with a broad range of equipment and tools available at affordable rental rates. This is why Tasman is the favoured go-to company for many oil and gas companies working in Australia and New Zealand looking to rent downhole rotary drilling tools.

Tasman take great pride in the diversity of downhole drilling products and services supplied to current, new and emerging global markets, to enhance the efficiencies and cost savings of our customers’ drilling programs.

If you are looking for drilling equipment and drill pipe rental service that will meet deadlines and deliver on time, you will find no better company to work with than Tasman. Our tools can be used for both offshore and onshore oil & gas drilling, coal bed methane, carbon capture storage, water drilling and geothermal drilling operations.

Tasman offers a wide range of oilfield equipment rentals for standard and high profile drilling operations. Tasman provides a large varied selection of drilling equipment that may be used in the Bottom Hole Assembly of the drill string which includes hydraulic and mechanical drilling jars, shock tools, string and near bit roller reamers, hole openers, stabilizers as well as a large variety of drilling subs, including the PBL circulating sub.

Our services don’t stop with providing you with the necessary equipment you need for your onshore & offshore drilling operations, but extends to in-house equipment inspection, repair, service and maintenance, qualified personnel and specialized third party tool services. The company ethos of repairing and maintaining all equipment to International standards of certification and compliance, coupled with stringent QA/QC procedures and extensive personnel training ensure that the best end deliverable is experience time after time.

Tasman is highly accredited and awarded, fully insured and protected so you never have to worry about any extra costs and charges when you work with us. There are no hidden fees. We value honesty and integrity and consider them as part of our code of ethics. Many of our clients are return clients because we know how to keep relationships going. Every client that walks through our doors or contacts us via email is a client that we want to keep for life. So we will do everything in our power to make your stay with us as easy and enjoyable as possible. We take time to get to know our clients so that we can help them find the right solutions for their business. No question, query or concern is ever taken lightly. We value your trust and your contribution and always delight to hear from you. So wherever your operations are based, Tasman has the downhole drilling tools you are looking for. Look no further for all your oil and gas drilling tools and contact us today!