goodwin mud pump brands

Manufactured since 1982, Goodwin pumps have been continually developed to create the world’s most dependable submersible pumps. Goodwin pumps can have electric or hydraulic motors to suit a multitude of tasks. The range of heavy duty slurry pumps us complemented by specialist acid resisting and high head dirty water submersible pumps.

Goodwin can supply a range of cables specially selected and tested for use with slurry pumps. For 100 size pumps cable is supplied with galvanised steel armouring to protect against damage. The IP68 rated cable gland seals against both the inner and outer sheaths, so even if the outer sheath is damaged water cannot ingress to the electrical connections.

The Goodwin pump uses high quality brass end rings and bars in the rotor that are brazed together. Brazed brass construction is proven as being more robust and reliable than die cast alternatives when the pumps are subjected to high energy Direct On Line (DOL) starts.

The Goodwin pump motor runs submerged in oil that lubricates and cools the bearings and the mechanical seal. The oil dissipates heat from the hottest part of the motor to the high mass stator housing that acts as a heat sink, eliminating motor hot spots which can give premature motor winding failure.

The Goodwin pump benefits from forced convection cooling by nature of the pumped fluid passing around the motor housing before it leaves the pump. This allows the pump to run for extended periods of time even if it is run semi-submerged. This is an integral part of the design and makes the requirement of additional motor cooling unnecessary.

To balance the load on the pump shaft, bearings and mechanical seal, Goodwin use a twin volute casing, reducing vibration and extending the life of all component parts especially the mechanical seal.

Removable Discharge ElbowThe 150 and 200mm Goodwin Pumps are supplied with a removable and replaceable discharge elbow made from precipitation hardened Stainless Steel.

Non-Pressurised Mechanical SealSuitable for submergence depth up to 28 metres as standard. The Goodwin mechanical seal is only subjected to the pressure from the submergence depth of the pump which generally is only a few metres of head and not the discharge pressure of the product. This greatly reduces the chance of fluid ingress into the motor itself and the destructive consequences which can result. The seal is positioned directly below the lower bearing to give it maximum support and protection from vibration.

The wet end of all Goodwin slurry pumps are made of NiHard alloy. For very abrasive applications Goodwin can offer tungsten carbide coated impellers, inducers and wear plates as it is possible to coat 100% of the rotating surface exposed to the slurry and thus provide the customer with excellent component life. Closed vane impeller designs have surfaces which can’t be tungsten carbide coated. 150 and 200 size slurry pumps have tungsten carbide coated wet end parts as standard. For 100 size pumps, coating is optional.

This feature assists the breakdown of large particles in the impeller that might ultimately lead to a blocked pump. There is little if any chance of the impeller becoming blocked as opposed to closed vane impellers which are often blocked and tend to stay blocked.

To reduce the bending moment on the shaft, when it comes into contact with large particles, the Goodwin inducer is kept as close as possible to the lower bearing.

The Goodwin Submersible Slurry Pump was developed for the UK mining industry and has since grown into a range of products that deliver proven performance in the most demanding environments.

Product development is performed in the UK, however all pump production manufacturing is done at our high quality, low cost manufacturing operation Goodwin India Pvt Ltd, located in Chennai, India, which was started in 2005.

Within the purpose built 70,000 sq feet factory area, submersible pumps are machined and assembled at our Indian facility, utilising the latest equipment to ensure we manufacture extremely reliable, high quality pumps.

From the initial start-up in India in 2005, there were three variants of a 30Kw 100mm pump designed and manufactured. Now that the range has been properly developed, there are five variants of 100mm, 150mm and 200mm submersible slurry pumps, two variants of ultra-reliable multistage submersible dirty water high head pumps for mine dewatering, as well as acid resistant super duplex stainless steel pumps for chemical ponds and acid leaching applications.

Goodwin submersible pumps are electrically-driven, abrasion resistant submersible pumps that are capable of pumping dense slurries containing abrasive solids within a wide range of industries.

Due to the arduous duties our submersible pumps are subject to in all locations that we service, we ensure that there is exemplary back up and support to make sure our customers’ sites remain operational; this is because it is necessary to maintain, repair and replace wear parts on pumps when pumping abrasive slurries.

As well as pumps, our companies can deliver tailored pumping solutions with custom made pontoons and slurry handling systems specifically aimed at tailings reclamation applications.

Hydroman™ 250TJQ Submersible Slurry Pump is a submersible electric sump pumping solution that offers advanced pump features for a variety of solids handling requirements. The TJQ submersible slury pump makes extensive use of Hydroman" finite element stress analysis and state of the art solids modelling to ensure reliable, long-wearing, solids handling capability.

200TJQ Submesible Slurry Pump comes standard with indispensable time-saving features including a moisture detector for early detection of intrusion of fluid into the motor chamber or mechanical seal, and a T-bolt construction that allows for rapid disassembly of the pump end for maintenance access.

They are available in a variety of colors and graphics, sizes. Goodwin slurry pumps are sale at wholesale prices on Alibaba.com. They are water-efficient, and environmentally friendly.@@@@@

A goodwin slurry pump is one of the most versatile applications for pumping, watering, various stages, and sizes of slurry pumps. You can find a goodwin slurry pump in various sizes, shapes, and sizes on Alibaba.com. Goodwin slurry pumps come in various sizes, shapes.@@@@@

Goodwin submersible slurry pumps are a great choice for drying, slurry pumping like a water pump, is allows for water volume to flow through. The water circulates the liquids into the liquids pool, and allows liquids to evaporate faster.@@@@@

Goodwin slurry pumps are water efficient, and they don"t require water because all the components of the water are similar to their pumps, they are water-efficient, and has a wide volume of flow. It also has a low water consumption, and long service life. They also have a great water quality, low maintenance, and long-term life.

The heavy duty pumps are equipped with a patented external inducer that breaks dowm and re-suspends settled or compacted solids, allowing them to easily transfer a very high percentage of solids to water.

Remko submersible slurry pumps are heavy duty, top discharge, dewatering pumps designed for very dirty water, tailings, sludge, mine waste, farm wastes. They have a heavy duty inlet agitators and are suitable for pumping....

Mud Pumps come in both electric and gas / diesel engine drive along with air motors. Most of these pumps for mud, trash and sludge or other high solids content liquid dewatering, honey wagon and pumper trucks. Slurry and mud pumps are often diaphragm type pumps but also include centrifugal trash and submersible non-clog styles.

WARNING: Do not use in explosive atmosphere or for pumping volatile flammable liquids. Do not throttle or restrict the discharge. Recommend short lengths of discharge hose since a diaphragm mud pump is a positive displacement type and they are not built with relief valves.

To reduce the bending moment on the shaft, when it comes into contact with large particles, the Goodwin inducer is kept as close as possible to the lower bearing.

To balance the load on the pump shaft, bearings and mechanical seal, Goodwin use a twin volute casing, reducing vibration and extending the life of all component parts especially the mechanical seal.

The Goodwin pump uses high quality copper end plates and bars in their rotor that are brazed together where the melting point of the braze is 787°C. Goodwin chose this over aluminium end rings and bars as aluminium has a lower melting point of 507°C and is susceptible to porosity if die-cast leading to premature rotor failure under severe conditions.

The Goodwin pump motor runs in a submerged oil bath that lubricates and cools the bearings and the mechanical seal. Additionally it transmits heat from the hottest part of the motor to the high mass stator housing that acts as a heat sink, eliminating motor hot spots which can give premature motor failure as would be the case if it was not oil filled.

The Goodwin pump benefits from forced convection cooling by nature of the pumped fluid passing around the motor housing before it leaves the pump. This allows the pump to run for extended periods of time even if it is run dry in fresh air (when other pumps would overheat and burn out) or even if it is only semi-submerged without over heating. This is an integral part of the design and makes the option of additional motor cooling a redundant expense.

Continental Emsco Drilling Products, Inc., which consisted of Emsco drilling machinery and Wilson mobile rigs, was purchased by National-Oilwell, Inc on July 7, 1999. To our knowledge, no pumps have been manufactured and sold under the Emsco brand name since National-Oilwell acquired them.

Fairbanks Morse pumps are currently manufactured in Kansas City, Kansas. Fairbanks Morse is a division of Pentair ever since August, 1997 when Pentair purchased the General Signal Pump Group.

Gaso pumps are manufactured by National Oilwell Varco. Gaso was acquired as "Wheatley Gaso" by National-Oilwell in the year 2000. At the time, Wheatley Gaso was owned by Halliburton.

Skytop Brewster pumps are no longer available as new pumps. Skytop Brewster(Cnsld Gold), a unit of Hansen PLC"s Consolidated Gold Fields subsidiary, was acquired while in bankruptcy by National-Oilwell, Inc. in November, 1999.