mud pump api free sample

A wide variety of api 7k mud pump. options are available to you, such as 1 year, not available and 2 years.You can also choose from new, used api 7k mud pump.,As well as from energy & mining, construction works , and machinery repair shops. and whether api 7k mud pump. is 1.5 years, 6 months, or unavailable.

Fluid loss is one of important drilling fluid properties and two type of fluid loss are API and HTHP fluid loss. This article will explain about both of them and effect on the drilling operation.

API Fluid Loss Test (low-pressure, low-temperature filtration test) is a test used to measure a filtration of mud with ambient temperature and 100 psi differential pressure. The API fluid loss testing equipment is shown below (Figure 1).

If drilling fluid has good fluid loss property, it will show a thin and impermeable mud cake. Please keep in mind that this test is based on the surface condition, and it may be in error because it does not simulate downhole conditions. The API fluid loss test can lead you to the wrong conclusion, because at the surface condition the test demonstrates very good fluid loss and a very thin filter cake.When the drilling mud is in a downhole condition, wellbore temperature and pressure can dramatically change drilling fluid properties.The best way to test the fluid loss is to simulate wellbore condition at high pressure high temperature in order to see what the fluid loss property will be. The procedure is called” HTHP Fluid Loss.”

The HTHP fluid loss test is similar to the API test because it indicates information on drilling mud filtration into the formation under a static condition over a certain period of time.

For the HTHP fluid test, both temperature and pressure can be varied to represent an expected downhole condition. The HTHP testing equipment has a heating jacket so you can heat up the drilling fluid sample to the expected wellbore temperature. Typically, the recommended temperature in the heating jacket should be above the estimated temperate of about 25 F to 50 F. The test pressure is normally at 500 psi differential pressure.  Normal test conditions are 150 F and 500 psi differential pressure and the maximum allowable test temperature is 300 F with the standard equipment. Mud filter cake thickness must be maintained below 2 mm. The HTHP test is performed for 30 minutes, just like the API fluid lost test.

If the drilling mud does not have good fluid loss property, fluid with small particles in the drilling mud can be invaded into formations and it will cause formation damage. This will directly affect the production rate of the well once it starts producing.

The drilling fluid that has bad fluid loss will form a very soft and thick mud cake across permeable formations. This can lead to differential sticking because of an increase in the contact area between formation and drill string.

A thick mud cake across porous zones can be easily formed because the drilling mud has high fluid loss values. The thicker the  mud cake is, the more torque and drag are experienced while performing the drilling and tripping operations.

The American Petroleum Institute (API) released its 2015 publications programs and services catalog this year. The 2015 edition lists API standards, recommended practices, equipment specifications, technical documents, and reports and studies on the oil and natural gas industry’s safety, efficiency, and responsibility to supply energy to the world. This catalog includes the updated API 7K standards for 2015 as well.

API Spec 7K (Drilling and Well Servicing Equipment) was last updated in 2010 in its Fifth Edition. It provides general principles and specifies requirements for design, manufacture, and testing of new drilling and well-servicing equipment and of replacement primary load-carrying components.

The API Spec 7K catalog (Product Number 807K05) is 105 and can be purchased from API for $182. There is also a Chinese translation (Product Number G07K05C) available for $128.

In the same way that the FDA requires comprehensive documentation from food manufacturers, API requires comprehensive documentation for everything from repair welding to proof load test records to operation and maintenance manuals.

API Spec 7 2010 also includes a comprehensive listing of best practice guidelines for just about any drilling and well servicing equipment operations you can think of.

An innovative product policy and continuous advancement of essential design features make this pump a powerful, yet economical standard unit with a broad range of applications.

Professional China Mud Pump - BNS series Single Stage, End Suction Norm Centrifugal pumps – Beken, The product will supply to all over the world, such as: , , ,

Mystique Mud pump Coolant and Lubricant extends mud pump liner and piston life and provides internal lubrication and extra cooling to the coolant system of mud pumps. It extends the life of all liners, even ceramic. Mystique will not cause corrosion or rusting of iron, and is safe with all alloys. Recommened dilution rate of 12.5%. (25 gallons will treat a 200-gallon system.) For use on closed systems.