mud pump lubi price

The pump volute shall be of cast Iron as per grade FG 260 of IS 210/ISO 186 with vertical discharge port. The pumps shall have non clog semi open impeller with material of construction of Cast Iron (standard supply), CF8 and CF8M, suitable for pumping liquids up to 50 deg. C.

The Pump shaft sealing shall be accomplished with double mechanical shaft seal of material Carbon /Ceramic/NBR/AISI 304 Up to 1 Hp and above 1 Hp the mechanical shaft seal material shall be Sic/Sic /Viton /AISI 316 on the pump side.

The pump shall be close coupled with a dry submersible motor, having class F insulation, IP 68 protection, 2900 rpm, epoxy sealed cable entry, with S1 duty for fully submerged and S3 duty for partially submerged application.

Product data The Lubi LBM series are self-priming, horizontal, single-stage, centrifugal, end-suction pumps. Pumps are available from 0.75 to 2.2 kW in single-phase and from 0.75 to 7.5 kW in three-phase power supply. Motor and pump are close coupled in a convenient and compact design for quick installation in limited space. They are also available as bare pump unit which are suitable for coupling with motor / engine. The pump is fitted with a gland packing and single piece pump-motor shaft (in close coupled version). Mechanical shaft seal is available in 0.75 kW models. The pumps have...

Product data Operating conditions Head range The pump is fitted with a Totally Enclosed Fan Cooled, 2-pole or4-pole induction motors which performance Liquid temperature range: 0°C to +90°C Total suction lift : Up to 8 metres Pumped liquids These pumps are designed for liquids which are non- aggressive and non-explosive, muddy water, with or without solids up to 20 mm grain size or fibres. Pump location The pumps have been designed to operate in a non- aggressive and non-explosive atmosphere. The relative humidity should not exceed 95%. Curve conditions The conditions below apply to the...

Base frames Base frames The dimensional sketches below show the dimensions of the base frames fitted to LBS pumps. The type number of the base frame is stated for each LBS pump mentioned in the Technical data. Base frame type No. Base frame

Lubi Electricals Limited. Near Kalyan Mills, Naroda Road, Ahmedabad-380 025, INDIA. Sales Enquiries: mktsales@lubipumps.com, expsasles@lubipumps.com Product Improvement is a continuous process at "LUBI". The data given in this publication is therefore subject to revision.

Our range of products include dharani ss sewage pump, lubi heavy duty sewage / effluent pumps, lubi drainage pumps, las series construction drainage pumps and lubi submersible drainage pump.

Part Name Material Motor Housing SS 304 Pump Casing SS 304 Impeller SS 304 - Vortex Shaft SS 304 Mechanical Seal Carbon Vs. Ceramic Silicon Carbide Vs. Silicon Carbide

The pumps shall have non clog, semi open or closed type impeller with material of construction of Cast Iron FG260 (standard supply), CF8 and CF8M, stainless steel shaft, suitable for pumping liquid up to 50 deg. C.

The pump shall be close coupled with dry submersible motor, having class F insulation, IP 68 protection, epoxy sealed cable entry, with S1 duty for fully submerged and S3 duty for partially submerged, suitable for 3 phase, 415volts, 50 Hz power supply.

The pump shaft shall be made of stainless steel as per ASTM A582 and grade of AISI 410. The Pump shall be supplied with mechanical shaft seal with material of construction of Carbon/ceramic/NBR/SS304.

The pump shall be close coupled with dry submersible motor, having class F insulation, IP 68 protection, 2900 rpm, rubber sealed cable entry, with S1 duty for fully submerged and S3 duty for partially submerged, 1 phase, 240 volts, 3 phase, 415 volts

The pump shall be close coupled with a dry submersible motor, having class F insulation, IP 68 protection, 2900 rpm, epoxy sealed cable entry with S1 duty, 3 phase, 415 volts, 1 phase, 240 volts.

Browse through the extensive list of Submersible Pumps at Moglix. Shop online for other Lubi Submersible Pumpsavailable at Moglix in the lowest price range.

Pumps play a major role in pumping up the fluids. Lubi LBM355 5HP Three Phase Swimming Pool Pump is an ideal choice when you are looking for an efficient one. This is a Three Phase pump. This submersible pump is connected with motors for proper ejacuation of water. This pump is known for its durability and high performance. The submersible pump is very compact, thus the installation process gets easy. Moreover, it is made from premium quality materials. This pump is certified and has passed all quality tests. Lubi brings you one of the best submersible pump available in the market.

Lubi PumpsOffering you a complete choice of products which include end-suction centrifugal monoblock pumps, multi stage multi outlet fire pumps, horizontal split case fire pumpset, hpn pressure booster systems, lcrh series high-pressure vertical multistage centrifugal pumps and lubi long coupled end suction centrifugal pump.

The pump casing shall have material of construction of Cast Iron FG 260 (standard supply), Bronze LTB2, CF8, CF8M, axial suction and radial discharge port, dynamically balanced impeller, steel shaft, stainless steel shaft sleeve.

The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

The pump shall be close coupled with a totally enclosed fan cooled type (TEFC) Induction motor, with F class insulation, S1 duty and IP55 protection, suitable for 3 phase 415 volts, 1 phase, 230 volts power supply.

The pump shall have back pull out design so as to enable the rotating parts to be removed and serviced without dismantling the suction and discharge pipe work.

The pump casing shall have threaded ports near suction and delivery flanges for installing suction and discharge pressure gauges. The pump shall also have a threaded drain port at the bottom of casing for draining the pump during maintenance.

The pumps shall be non-self-priming, vertical multistage centrifugal pumps. The pump consists of a base and a pump head. The chamber stack and the outer sleeve are secured between the pump head and the base by means of tiebolts. The base has suction and discharge connections on the same level (in-line). All pumps shall be equipped with a maintenance-free mechanical shaft seal.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection, 3 phase, 415 volts, 1 phase, 230 volts, 50 and 60 Hz power supply.

The pump casing shall have material of construction of Cast Iron FG 260 (standard supply) or CF8 (AISI 304), inline suction and discharge port, closed type impeller, stainless steel shaft.

The pump suction and delivery flange connection shall be as per PN 16 standard up to 16 bar pump shut off pressure and as per PN25 for pumps with shut off pressure above 16 bar.

The pump shall be coupled with a Totally Enclosed Fan Cooled (TEFC) type induction motor, with F class insulation, S1 duty and IP55 protection, 3 phase, 415volts, 50 Hz and 60 Hz power supply.

The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection. 1 phase, 230 volts, 50 Hz (Standard Supply), 3 phase, 415 volts, 50 Hz.

A water detector is provided in the seal chamber. In case of seal failure if water enters the seal chamber, a signal can be sent to the control panel so that the pump operator is made aware of a potential seal leakage problem.

These pumps shall be available in Noryl or Polypropylene material of construction and closed coupled with standard TEFC motor. They are also available as long-coupled with standard TEFC as well as Flame Proof motor.

The pumps are made of non-metallic, glass-filled Polypropylene construction offering chemical resistance to most acids, alkalis, and inorganic solvents as does the Noryl series.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection. 1 phase, 230 volts, 50 Hz (Standard Supply), 3 phase, 415 volts, 50 Hz

The pump shall be designed for muddy water or liquids or effluents with solids or fibers. The liquid shall be compatible with material of construction of the pump.

Waste treatment: Pumping polluted, hot or corrosive waste water containing sand, mud or solids, in suspension, dosing neutralizing liquid, pumping out settled sludge.

The pump shall have back pull out design so as to enable the rotating parts to be removed and serviced without dismantling the suction and discharge pipe work.

In LCR The pump base and head cover shall be of Cast Iron grade FG 260 as per IS 210/ ISO 186 with inline suction and discharge connection. In LCRI the pump base shall be made of CF8 material, the pump head shall be of Cast Iron grade FG 260, pump head cover shall be of CF8M material. In LCRN The pump base and head cover shall be made of investment cast CF8M Stainless steel.

The pump shall be close coupled with a totally enclosed fan cooled type, 2900 rpm Induction motor with F class insulation, S1 duty and IP55 protection, 3 phase, 415 volts, 1 phase, 230 volts, 50 and 60 Hz power supply

Applications Marine - Pumping water from docks, Ports, vessels. Industrial - Pumping petroleum products, Chemical effluents, Sewage, ash-water etc. Civil construction - Dewatering foundations, trenches and pits. Mobile Machinery - Cooling water for marine engines and shovels. Public utilities - Sewage pumping.Motor 2 - pole induction motor 50Hz (n = 2900 RPM) 4 - pole induction motor 50Hz (n = 1440 RPM) Single phase: 230V +5, -15 % Three phase : 400V +5, -15 % Insulation class F Protection IP 44 Constructed in accordance with IEC 34.

Electric PumpProminent & Leading Manufacturer from Coimbatore, we offer sewage submersible pump, sludge pump, mub pump / self priming mud pumps / lubi lbm, plastic drainage pump, self priming pump and grinder pump.

In order to keep the ever growing demand of our clients, our company is involved in offering a wide range of Sludge Pump. This Sludge Pump is made with fine quality of material. As per the demand of our customers, we are providing this product at market leading prices.

Self Priming Mud Pump is a pump that is capable of moving mud and generating a vacuum in the suction line to lift the mud and fill the internal chamber. It can handle mud usually up to high inches. It is more flexible, versatile, and portable to use. The self-priming mud pump is designed in such a way that it allows pumping out a certain amount of mud, dirt, and suspended solid

To attain the maximum of our clients, we are engaged in offering a supreme quality assortment of Plastic Drainage Pump. Our product is made with fine quality of material and able to perform its working for long period of time. These products are tested on different quality parameter before dispatching to the market.

We are counted as prominent name in this domain, involved in offering supreme quality range of Self Priming Pump to our clients. This Self Priming Pump is extensively used in different industrial regions and widely appreciated for easy installation and excellent performance. We are providing this product at market leading prices.

With the help of our expert team members, we have been able to offer a wide range of Grinder Pump. These are precisely designed and developed using best available technologies and following international industrial standards. Our pumps are available in various dimensions and thickness as per the requirements of clients.