mud pump valve pot pricelist

Mud Pumps are available for the different purposes of drilling and extracting of oil. In fact, the Unitized Pumps are a work of the hydraulic mechanical transmission. Unitized pump parts include 4 types of packages such as the air clutch transmission takes in the diesel engine, transmission (including card and shaft, decelerator, clutch, belt and pulley) and the Mud pump. The Mud Pumps are also inclusive of the hydraulic coupling transmission that consists of the diesel engine, hydraulic coupling and the Mud pump. It also includes the electric drive Mud pump and the chain transmission for apt design and assembling.

The Unitized design Pumps are built as well as licensed according to the specifications of the American Petroleum Institute where the master skid is the standard oilfield 3 runner skid. Mud Pumps like the F 1000 are driven by the diesel engine with the help of the narrow V belts. Pumps are complete with a bulk wheel, a set of V belts, a screw assembly, a belt guard and the screw devices for tightening the belts. Mud pump like the triplex liner single action pumps has an input power of 1000 horse power. The maximum stroke is all of 10 inches or 254 mm.

Mud parts also contain a maximum working pressure of 5000 PSI or 35 MPA. The Mud Pumps have a gear type made of integral herring bone with API 6 valve pots. The intake of the F 1000 Pumps is 12 inches or 305 mm and they have a discharge space of 4 inches or 102 mm. Mud pump also contain a pulsation dampener model that has a capacity of 75.7 liters or 20 gallons. The relief valve and pressure gauge are also an important part of the Mud pump as they help in various ways.

Mud pump like the diesel engine has a rated speed of about 1200 revolutions per minute and the movement takes place in an anticlockwise direction with the face output shaft end. For the purpose of testing and commissioning, the Mud pump needs to be installed and secured with machinery and different kinds of equipment. Furnish the lube products for testing and the diesel is required to be run for testing the transmission devices. To give you an idea, the Mud pump that is being discussed in this category is available at competitive prices and can be obtained for pneumatic clutch transmission that can be adjusted according to customer’s requirements.

Choose a used Emsco FB-1600 Triplex Mud Pump from our inventory selection and save yourself some money on your next shallow drilling oilfield project. This Emsco FB-1600 Triplex Mud Pump is used and may show some minor wear.

We offer wholesale pricing on new Emsco FB-1600 Triplex Mud Pump and pass the savings on to you. Contact us to compare prices of different brands of Mud Pump. This equipment is brand new and has never been used.

Our large network often has surplus Emsco FB-1600 Triplex Mud Pump that go unused from a surplus purchase or a project that was not completed. Contact us to see what Emsco FB-1600 Triplex Mud Pump we have in inventory. The surplus Emsco FB-1600 Triplex Mud Pump are considered new but may have some weathering depending on where it was stored. Surplus oilfield equipment is usually stored at a yard or warehouse.

We have refurbished Mud Pumpthat have been used and brought up to functional standards. It is considered a ready to use, working Mud Pump. Please contact us for more information about our refurbished Emsco FB-1600 Triplex Mud Pump. These Mud Pump have been used and brought up to functional standards. It is considered a working Mud Pump. Please contact us for more information about the product.

? Its compact structure, lighter weight, and small size with high efficiency can be matched with kinds of pump devices according to drilling rig’s requirement and different conditions.

? Its durable fluid end has greatly improved triplex pump’s function and capacity, what’s more, its independent design is easy to inspect and convenient to maintenances.

W-440 Well Service Pump is a continuous duty 6" stroke high performance triplex. This pump is an Ellis Williams Style (EWS) design. The W-440HP is rated to 5,000 PSI, with 3-1/2" Piston/Liners, with a maximum output of 5.3 BPM. Our W-446 is a 3K pump and can accommodate from 3" liners/pistons to 6" liners/pistons. W-446 can turn out 15 BPM with 6" liners at 1027PSI.

Drilling pump is also called mud pump, which transport high pressure, high specific gravity, high sand concentration drilling fluid to bottom of hole. Drilling fluid is used to cool bit, wash out bottom of hole, break rock and bring out debris. Drilling pump not only is indispensable and one of the most important processing equipments, but also is one of the three working machines of drilling rig.

DUPM mainly manufactures series mud pumps such as DTF-500, DTF-800, DTF-1000,DTF-1300 and DTF-1300, etc. Since our company realized localization of components of hydraulic end until independent R & D and production of drilling pump,we have been committed to the continuous optimization and upgrade of the drilling pump. Our DTF series products is becoming better to service oil field drilling through constant communication with customers.

5. Valve pot, crankshaft, herringbone gear and other important parts are manufactured by high quality alloy steel. Herringbone gears adopt grinding process, which make the precision of gears higher.

Advanced structure, small volume, high reliability and easy for maintenance.API 7# valve adopted, suction valves and discharge valves can be interchanged.Hydraulic cylinder is alloy steel forged. Piston rod is a two piece, fast change.

Calibration pot is one of the main equipment in the chemical injection package, which is used to increase the accuracy of injection based on the required flow rate. Calibration pot is produced in different sizes and is a kind of accurate measuring tool for tanks that need to be injected with different chemicals. Seven Industrial Group; Manufacturer of calibration pot and other wastewater treatment equipment, which provides a comprehensive guide for this group of products. This guide covers important standards in designing, making calibration pots, prices and everything you need to know about this product.

Calibration pot, measuring container, calibration cylinder or calibration pot are all the names of a device and a container with different sizes, which is included in the equipment package of chemical injection package. A calibration cylinder is a container made of glass, PVC or stainless steel that has degrees on its body and determines the injection flow rate of the pump. In different water treatment tanks, it may be necessary to inject chemicals with a specific flow rate based on fluid pressure and environmental conditions. In this case, the calibration pot is installed before the injection pump and its task is to control the amount of injection material into the desired fluid in the tank after the pump.

Calibration pot can be divided into different groups according to the material, size and type of charging. Each of these groupings assigns specific features to the calibration pot, which include:

The material used for the body of the calibration pot is determined according to the type of chemicals. In general, it is better to consider materials for this purpose that reduce the possibility of corrosion due to contact with chemicals. Most of the time, these cylinders are made of glass, which has a high resistance to temperature and impact. In addition, depending on the environment, the calibration pot may be made of PVC and stainless steel.

To adjust the injection pump flow, the calibration pot must first be filled with the amount of chemicals that must be injected at the desired time interval. How to charge or fill the material inside the calibration pot is done by two methods of gravity and suction. If the calibration pot is located below the tank, it will be filled or charged by gravity method, and if it is installed above the tank, it will be charged with the help of suction pumps.

As mentioned, the calibration pot is installed before the chemical injection pumps to accurately measure and adjust the injection flow. Therefore, after the chemical tank, the inlet valve is placed in the calibration pot and the chemical enters the container to the extent of the capacity determined for it. After filling the calibration pot capacity, the first valve closes and the second valve, which transfers the chemicals to the injection pump, opens and the injection operation takes place. This cycle will continue until the required time and based on the purpose and location of the chemical injection package.

One of the most important points to consider in designing a calibration pot is how to size and calibrate the device. In general, according to the standards for calibration pot design, for large pumps the size of this equipment is one-minute pump discharge and for small pumps, two minutes’ pump discharge is considered. Other important items in the design and construction of calibration pots are the material used for the body and other connections in them. Strong glass is often considered for their body and stainless steel is used for its holding parts to be sufficiently resistant to chemicals.

Seven Industrial Group is one of the largest design, production and manufacturing teams of calibration pots in different sizes. It should be noted that all products designed and built in this complex are under the supervision of professional and experienced engineers in the field of water and wastewater treatment. Due to the high variety of products and equipment of Seven Industrial Group, we suggest that you contact the experts for a free consultation before buying a calibration pot.

The price of the calibration pot or calibration cylinder is measured based on the material of the pot body and also their size. Due to the fact that the material and size of each of these products are determined at the design stage of the calibration pot and based on the place of installation and use of this equipment, so the prices are completely different. To inquire about the price of the calibration cylinder, you can contact Seven Industrial Group through the communication channels mentioned at the bottom of the page.

In addition to the main application of the calibration tank, which is to measure and adjust the flow rate of chemicals according to fluid conditions, this group of equipment can be used for other applications as well. The most important applications of calibration pot are the following:

·         Check valve performance test after injection pump (if the fluid level in the calibration tank changes at the end of the pump course at once, it indicates a failure in the pump check valve)