pto mud pump pricelist

... mounting, the pump (at the front or rear) can be attached to a Unimog or a tractor, lifted and transported to the installation site. The pump is driven by means of the PTO ...

... speed. A hydraulic driven pump can produce higher pressures than PTO or belt driven pumps. They can also hold constant pressure at varying engine speeds ...

It is a portable type manure pump which can be driven by a tractor or electrical motor equipped with a special rubber rotor. It can pump high dry matter containing manure and liquids ...

The mobile pumps series "AT" have always been used all the time for direct crop irrigation. After having tested their flexibility and efficiency qualities, they are also widely used by land improvement co-operatives and ...

... Stallkamp long-shaft centrifugal pumps are heavy duty and are perfectly suitable for reception pits and manure pits to a depth of 6 m. Either with sturdy electric motors (up to 22 kW/30 PS) or PTO-driven, ...

"The Nuhn Triple Port Pump is an animal of a pump! I"ve been pumping manure since 1996, and over that time I"ve operated many other makes of pumps. Nuhn pumps are hands ...

SlurryKat recommend the use of DODA pumps with our systems, as prolonged use by our slurry contracts division has proven that they are efficient, robust and economic to maintain. Our contracts division has proven that ...

Add Lead Pump FunctionsUsing an engine with a rear-PTO, allows a booster to also operate attachments, such as a lagoon feeder. Equipped with the standard PCE Booster Bypass, the trailer is set-up to ...

When installed, this pump will be attached to the rear of the tractor using the three point hitch with the PTO shaft attaching to the 540 rpm, 6 spline PTO of the tractor. The gearbox shaft of the pump is also 540 rpm and 6 spline. Safety guards must be in place around the PTO shaft as it is dangerous when exposed. The gearbox must have the appropriate amount of SAE 90 gear oil from proper maintenance. It is designed to operate on a range of tractors with engine horsepowers from 15hp to 125hp and the rotational force of the tractor’s PTO shaft powers the pump by attaching to the shaft on the gearbox of the pump. You can adjust your tractor’s engine speed as needed to reach your appropriate rate. This pump has a flow rate of 352 GPM and must be operated in open and well ventilated areas. Pump must be drained prior to freezing temperatures.Specifications:

Comes with attaching hose barbs for both suction line and discharge lines, suction line strainer (filter net), and PTO shaft to attach pump to the tractor that is 540, 6 Spline on each end.

The ASC# 89164 sealed washer that fits in the hose connections, can get pinched if not careful, or can deteriorate over time, it is recommended to keep a couple of extras on hand so your pumping experience will not be halted.

If you are supplying pump supplies, you can find the most favorable prices at Alibaba.com. Whether you will be working with piston type or diaphragm type systems, reciprocating or centrifugal, Alibaba.com has everything you need. You can also shop for different sizes pto water pump wholesale for your metering applications. If you operate a construction site, then you could need to find some concrete pump solutions that you can find at affordable rates at Alibaba.com. Visit the platform and browse through the collection of submersible and inline pump system, among other replaceable models.

A pto water pump comes in different makes and sizes, and you buy the tool depending on the application. The pump used by a filling station is not the one you use to fill up your tanks. There are high flow rate low pressure systems used to transfer fluids axially. On the other hand, you can go with radial ones dealing with a low flow rate and high-pressure fluid. The mixed flow pump variety combines radial and axial transfer mechanisms and works with medium flow and pressure fluids. Depending on what it will be pumping, you can then choose the pto water pump of choice from the collection at Alibaba.com.

Alibaba.com has been an excellent wholesale supplier of pto water pump for years. The supply consists of a vast number of brands to choose from, comes in different sizes, operations, and power sources. You can get a pump for residential and large commercial applications from the collection. Whether you want a pump for your home, or run a repair and maintenance business, and need a supply of po water pump, you can find the product you want from the vast collection at Alibcom.comther Whether it is for refrigeration, air conditioning, transfer, or a simple car wash business, anything you want, Alibaba.com has answer.

Explore a wide variety of tractor pto pump on Alibaba.com and enjoy exquisite deals. The machines help maintain drilling mud circulation throughout the project. There are many models and brands available, each with outstanding value. These tractor pto pump are efficient, durable, and completely waterproof. They are designed to lift water and mud with efficiency without using much energy or taking a lot of space.

The primary advantage of these tractor pto pump is that they can raise water from greater depths. With the fast-changing technology, purchase machines that come with the best technology for optimum results. They should be well adapted to the overall configuration of the installation to perform various operations. Hence, quality products are needed for more efficiency and enjoyment of the machines" full life expectancy.

Alibaba.com offers a wide selection of products with innovative features. The products are designed for a wide range of flow rates that differ by brand. They provide cost-effective options catering to different consumer needs. When choosing the right tractor pto pump for the drilling project, consider factors such as size, shape, and machine cost. More powerful tools are needed when dealing with large projects such as agriculture or irrigation.

Alibaba.com provides a wide range of tractor pto pump to suit different tastes and budgets. The site has a large assortment of products from major suppliers on the market. The products are made of durable materials to avoid corrosion and premature wear during operations. The range of products and brands on the site assures quality and good value for money.

After using several of the “Big Name” pumps I was sure there wasn’t a product on the market that could move our drilling mud. I was having to use an excavator and two dump trucks to move the mud. We found Gator Pumps and purchased a 12″ PTO driven pump. We were able to move our mud in half the time with less effort. What used to require three pieces of machinery and three operators now requires one tractor and one worker checking on the pump periodically. We also use our Gator Pump to pump rain water off our pits. The pumps are almost maintenance free and absolute workhorses. Save yourself the frustration of trying to find the right pump for your operation. Just call Dale and the guys at Gator. They’ll fix you up and you won’t be disappointed.

GATOR Pump manufactures the highest quality trailer pumps, vertical pumps, floating, and hydraulic pumps. GATOR Pump is a recognized leader in moving water, sludge, slurries, and other heavy solids in some of the world’s most remote and challenging pumping applications. The GATOR team is committed to providing an efficient, personalized and low cost solution to satisfy your most urgent flow requirements. The GATOR Pump design team is available around the clock to examine, understand and solve your pumping needs

The Original GATOR Trailer PTO Pump is recognized industry wide for its high performance, tough design, easy maintenance and low operating cost. Our in-house manufacturing team reviews each order we receive in order to give our customers a personalized range of options for unique individual pumping applications. GATOR Pump builds the most durable and dependable centrifugal pump on the market and we want our equipment to last a lifetime: We have proudly stood behind our pumps for 38 years and are still maintaining and providing replacement parts to all of our customers.

GATOR Pump is a veteran owned corporation, established in 1977. We are still a family owned company operated by the original founders located in Brownwood, Texas. Our time tested fabrication process delivers quick response for all your immediate pumping needs. We are ready to work for you.

DuCaR PTO Pumps are an excellent choice for COST effective and high performance sprinkler irrigation. These pumps are quick and easy to setup to begin irrigating in minutes! If you have a tractor that you want to utilize as the power source, PTO Pumps are a great choice and are capable up to 195 m3/h water output with high pressure performance up to 81 m head. These pumps are completely cast iron construction. It comes complete with suction hose assembly, stand and FREE shaft.

The DuCaR DKT 125 Pump is a great match for a tractor up to 65 HP and running 2 of our model DuCaR Jet 50 Sprinkler with 50m shooting range or 1 of our large DuCaR Jet 70 Sprinkler with 70m shooting range. This pump will provide flow rates from 40 to 195 m3/h and pressures as high as 120 psi!Modeldd/rpmkwQ/(m"/h)Hm (mss/mwc)SuctionDischarge

IrrigationBox proudly presents Rovatti single & multi stage centrifugal pumps with overgear driven by cardan shaft of PTO. Designed for clean, waste water, slurry, sewage with solids and fibres, grey waters, recycled and active sludges.

Rovatti T and TK series of horizontal centrifugal CELAN WATER pumps are fitted with an over gear transmission box to be driven from a tractor or similar with a PTO outlet via the use of a cardan shaft. Also available with a 3 point linkage or on a 2 wheeledtrolley. These pumps are highly suited for irrigation and washdown systems. A large range of single and multistage pumps to choose from with flows up to 90 m3/h and heads up to 127 m.

In addition to clean water pumps, Rovatti provides TL and TLK series of horizontal single-stage tractor PTO drive SLURRYpumps with heads up to 130 m and flows to 63 m3/h. These pumps can be fitted with special pre-inlet choppers to reduce the intake load to a slurry. Also we have a variety of 3 point linkage frames available to carry these pumps.

AfghanistanAlbaniaAlgeriaAmerican SamoaAndorraAngolaAnguillaAntarcticaAntigua and BarbudaArgentinaArmeniaArubaAustraliaAustriaAzerbaijanBahamasBahrainBangladeshBarbadosBelarusBelgiumBelizeBeninBermudaBhutanBoliviaBonaire, Sint Eustatius and SabaBosnia and HerzegovinaBotswanaBouvet IslandBrazilBritish Indian Ocean TerritoryBrunei DarussalamBulgariaBurkina FasoBurundiCabo VerdeCambodiaCameroonCanadaCayman IslandsCentral African RepublicChadChileChinaChristmas IslandCocos IslandsColombiaComorosCongoCongo, Democratic Republic of theCook IslandsCosta RicaCroatiaCubaCuraçaoCyprusCzechiaCôte d"IvoireDenmarkDjiboutiDominicaDominican RepublicEcuadorEgyptEl SalvadorEquatorial GuineaEritreaEstoniaEswatiniEthiopiaFalkland IslandsFaroe IslandsFijiFinlandFranceFrench GuianaFrench PolynesiaFrench Southern TerritoriesGabonGambiaGeorgiaGermanyGhanaGibraltarGreeceGreenlandGrenadaGuadeloupeGuamGuatemalaGuernseyGuineaGuinea-BissauGuyanaHaitiHeard Island and McDonald IslandsHoly SeeHondurasHong KongHungaryIcelandIndiaIndonesiaIranIraqIrelandIsle of ManIsraelItalyJamaicaJapanJerseyJordanKazakhstanKenyaKiribatiKorea, Democratic People"s Republic ofKorea, Republic ofKuwaitKyrgyzstanLao People"s Democratic RepublicLatviaLebanonLesothoLiberiaLibyaLiechtensteinLithuaniaLuxembourgMacaoMadagascarMalawiMalaysiaMaldivesMaliMaltaMarshall IslandsMartiniqueMauritaniaMauritiusMayotteMexicoMicronesiaMoldovaMonacoMongoliaMontenegroMontserratMoroccoMozambiqueMyanmarNamibiaNauruNepalNetherlandsNew CaledoniaNew ZealandNicaraguaNigerNigeriaNiueNorfolk IslandNorth MacedoniaNorthern Mariana IslandsNorwayOmanPakistanPalauPalestine, State ofPanamaPapua New GuineaParaguayPeruPhilippinesPitcairnPolandPortugalPuerto RicoQatarRomaniaRussian FederationRwandaRéunionSaint BarthélemySaint Helena, Ascension and Tristan da CunhaSaint Kitts and NevisSaint LuciaSaint MartinSaint Pierre and MiquelonSaint Vincent and the GrenadinesSamoaSan MarinoSao Tome and PrincipeSaudi ArabiaSenegalSerbiaSeychellesSierra LeoneSingaporeSint MaartenSlovakiaSloveniaSolomon IslandsSomaliaSouth AfricaSouth Georgia and the South Sandwich IslandsSouth SudanSpainSri LankaSudanSurinameSvalbard and Jan MayenSwedenSwitzerlandSyria Arab RepublicTaiwanTajikistanTanzania, the United Republic ofThailandTimor-LesteTogoTokelauTongaTrinidad and TobagoTunisiaTurkmenistanTurks and Caicos IslandsTuvaluTürkiyeUS Minor Outlying IslandsUgandaUkraineUnited Arab EmiratesUnited KingdomUnited StatesUruguayUzbekistanVanuatuVenezuelaViet NamVirgin Islands, BritishVirgin Islands, U.S.Wallis and FutunaWestern SaharaYemenZambiaZimbabweÅland Islands

Road planers, dredges, and other equipment require power from some type of engine to perform their designed function. Without a power take-off, it would be necessary to add a second engine to provide the power required to run hydraulic pumps and other driveline attached equipment.

Adding an additional engine is simply not practical, which makes power take-off (PTO) a valuable element in providing power to secondary functions. To recognize their value requires a better understanding of these systems, their various types, and their diverse applications.

Power take-offs allow mobile crushing plants, road milling machines, and other vehicles to perform auxiliary functions without needing an additional engine to power them. A PTO is a device (a mechanism) usually seated on the flywheel housing, which transfers power from the driveline (engine) to a secondary application. In most cases, this power transfer applies to a secondary shaft that drives a hydraulic pump, generator, air compressor, pneumatic blower, or vacuum pump.

PTO choice is critical to provide sufficient power to the auxiliary equipment without severely limiting the main function of the prime mover. Selection of a power take-off requires specific information relating to the application and the power needs of the secondary or driven component.

Speed and rotation requirements of a PTO are among the most critical specifications in the list above, with speed being necessary for calculating torque. The torque and horsepower requirements of the driven component are essential for optimal performance.

Keep in mind that these calculations only apply to PTOs that drives a hydraulic pump. In cases where power take-off is providing power to a different type of drive component, it will require the manufacturer’s specifications of the driven element.

Though they perform the same general function—transferring power from the primary drive shaft to a secondary drive shaft for a driven component—there are various PTO types available that serve specific industrial applications. These diversifications are why WPT Power supplies OEM’s units in agricultural, energy, forestry, and road building sectors, among others.

The distinguishing characteristic of this type of PTO is the intentional removal of the pilot bearing. Benefits of this design feature come with an increased side load capacity, reduced inventory, increased uptime and engine life, and a quicker and easier installation. Industrial applications of the Pilotless Mechanical PTO include:

This type of flywheel PTO applies to either inline or sideload uses. It includes a sealed-for-life pilot bearing, utilizing a lever-actuated manual clutch. The benefit of this type of PTO is a straightforward installation which minimizes downtime and maintenance requirements. This type most commonly applies to:

This is a rugged, high-capacity power take off used in a broad range of industrial functions. Characteristic of this type of PTO are the sheaves between heavy-duty spherical roller bearings designed to utilize their full load potential. This bearing arrangement reduces the damage produced by crankshaft loading. Among the most common applications for the Type 1 PTO are:

The design of the Type 2 PTO features a heavy-duty side loading capacity using sizeable spherical roller bearings. Actuation of this PTO can be either hydraulic or pneumatic. It is self-adjusting and removes the need for the pilot bearing inside the engine flywheel. Features include reduced maintenance, less chance of premature failures, and improved engine and bearing life since there is no direct loading to the crankshaft. Common applications for Type 2 PTOs include:

This PTO design eliminates the need for the pilot bearing while providing increased side loading or inline potential. Its engineering accommodates the most demanding requirements of high-loading diesel engines. Features include simple installation, reduced downtime, and improved engine service life. This style of PTO is used on inline applications with its hydraulic and air fittings. They are mounted near the bell housing instead of at the rear of the shaft like type 1 and type 2.

The GM Style PTO reduces maintenance time and cost by using sealed main bearings and eliminating the need for the pilot bearing. Designed to mount directly to GM® style engines, these operate without the need for any particular PTO or engine adaptations. Notable features include clutch adjustments using an external ball stud and jam nut adjustment points.

Also known as “flat-faced” style PTOs, they incorporate similar design characteristics, features, and benefits of the GM style PTO. It is a spring-loaded clutch making it easier to engage and disengage than over the center power take-offs. Typical uses include irrigation units, brush chippers, or other gas or diesel engine applications.

PTOs are relatively simple mechanical units with minimal operational problems, but a few common issues are associated with them, and each has a straightforward solution. Here are some of the most frequently encountered issues:

PTO is hot. A newly installed PTO will run hot for the first 10-20 hours of operation after installation. Several issues contribute to overheating (220º F measured by infrared thermometer at the bearing carrier), including too much or too little grease, excessive sideload, or a new installation. Follow proper lubrication specifications and reduce the sideload to remedy the first two problems.

Getting the appropriate PTO to meet your operational needs is a priority at WPT Power. Manufacturing our PTOs takes place in our ISO 9001:2015 facilities, where all our products are engineered to meet the highest standards of quality demanded by our customers. ABS type approvals and ATEX certifications minimize risks, time, and costs. Type approval certification available: DNV & ABS (Others available on request)

Our broad range of products is developed to meet most requirements on standard industrial applications. Custom or modified PTOs are available for original equipment manufacturers (OEM) requiring specialized design and where volume is needed.

Power take-offs play an essential role in allowing for the transfer of power from a primary mover to a secondary or driven component without needing an additional separate engine. Various PTO types serve many applications, from smaller-scale operations to major industrial and construction projects. Choosing the correct PTO for a specific application is critical to the proper performance of the driven component.

Contact us for more information about the range of solutions offered by WPT Power Corporation, for assistance in selecting the right PTO to fit your specific application, or request a quote from one of our experts.

JASON MUD PUMP (SIMILAR TO HALLIBURTON HT-400)(Ref#2947T)  15k fluid end, 750 QSX Cummins (built 2014) with 7750 hours, Allison 6061 (rebuilt 2014), hydraulic charge pumpca, manifold  Price:  $239,500

OPI 700 HDL TRIPLEX PUMP(Ref#7719T)  700 hp at 150 rpm, fully rebuilt, Cat 3408 engines (approx. 15000 hours and run very well)  Two available  Price:  $275,000 CDN each

NATIONAL 12P-160 TRIPLEX MUD PUMP(Ref#5586T) 3 available in India. 1600 HP, rated pump speed 140 strokes per minute, maximum fluid cylinder liner bore 6¾”, stroke 10", 10,000 PSI hydrostatic pressure of standard cylinder. 2.853 ratio of gears. 10" suction connection, 6" discharge connection. Valve pot mod .7., steel fluid ends, 5,000 psi pulsation dampener. Oilfield skid mounted. Performance Data: at 120 strokes per minute with 6¾” liners, pump will produce 4305 PSI and 574gpm. Set up for electric power. Dimensions and weight: 84,700lbs, 209"L x 113"W x 75"H. Built 1976. Located India, removed from offshore drilling rig.

NATIONAL 12P-160 TRIPLEX PUMPS(Ref#2355R)  3 available, driven by GE752 traction motor, 1600 hp, 12” stroke, 5000 psi, surge chamber, skid mounted, located Middle East  Price:  $310,000

NATIONAL 12P-160 TRIPLEX PUMPS(Ref#8938R)  3 available, overhauled by National Oilwell (ready in 2-3 weeks after purchase), 1600 hp @ 120 stroke per minute, 12” stroke, 5000 psi, skid mounted, GE Amerimex 752 traction motors, new liners, seats, valves and pistons  Price:  $295,000 each

NATIONAL 12P-160 MUD PUMP(Ref#2062Re)  Refurbished, complete with South West fluid ends and DC traction motors, located Middle East, 3 available  Price:  $720,000 each

NATIONAL 8P80 TRIPLEX MUD PUMP(Ref#9073R)  800 hp, 6-1/2” x 8-1/2”, FS, FS FE w/QC caps and cylinder head caps, Oteco 3” shear relief valve, suction screen, 5 x 6” centrifugal charging pump, powered by Cat 3412 diesel engine, rod cooling pump, Oteco type D pressure gauge, mud valves, bull wheel, master skidded, complete, good condition  Price:  $275,000

NATIONAL OILWELL 850 HP MUD PUMP(Ref#15442T)  Mattco API-9 fluid end rebuilt, very little use after rebuild, pulsation dampener, no engine, skid mounted  Price:$22,000

NATIONAL 7-P-50(Ref#6302R)  750 hp, 8” stroke, 6” suction inlet, 4” discharge outlet, piston size 4-1/2” – 7”,  max rod load 85,000#, approx. weight 11,500#, lubrication force fed, steel pump power end, double helical gears, 4.95:1 gear ratio, rod bearings sheel type replaceable, main bearings straight roler, pinion bearings spherical roller, crankshaft 1pc forged alloy steel, connecting rod knuckle joint, crosshead guide bronze replaceable, piston type fluid end Monoblock design, from high strength alloy steel, treated and sonic tested, Cat D379 diesel engine, 500 HP max linear bore size 3-1/2 – 6-1/4 x 7-3/4” stroke, test pressure 10,000 psi, gear ratio 2.742.8” suction line to 4 discharge stroke, location South America  Price:  $110,000

NATIONAL JWS 165 WELL SERVICE TRIPLEX PUMP WITH 140 BARREL WORK TANK(Ref#2633Tb) 5 x 6, Detroit 8V71 engine, standard transmission, skid mounted   Price:$87,500

NOV JWS 340 TRIPEX MUD PUMPS(Ref#2345T)  Two available, Skidded, Detroit Series 60 diesel engine DDEC V (475 hp), Allison 750 (6-speed) transmission with lock up control pane, Mission 4 x 5 centrifugal suction pump, 4” plungers, pulsation dampener, pressure gauge, safety valve, 10,000 psi fluid end, 5000 psi working pressure, NOV plug valve control manifold (4-valve) configured for 15k operation.  Can be configured to kill wells, acidize, cement, reverse circulate, drill out frac plugs or run in tandem.  Self-contained with fuel and fluid tanks and controls.  Steel canopy over skids, covered battery boxes, new batteries and disconnect switches.  Well maintained and in excellent condition.  Low hours on pumps and motors.  Ready to work.  Price:  $154,500 each

NATIONAL JWS300 MUD PUMP(Ref#2767R)  Series 60 Detroit diesel, 14 liter engine w/Allison transmission, mounted on oilfield skid, major overhaul, completely unitized with fuel tank, fluid end rebuilt by Matco  Price:  $195,000

(2) NATIONAL C350 MUD PUMPS(Ref#3077N)  Standby – not pump in 15 years.  Pumped chalk continuously at 600 psi in a cement factory.  Complete with electrics and electric motor, complete, bull wheels and guards, complete, fluid end, pistons, liners, and valves.  Low hours.  Located Europe.   Price for both:  $105,000 loaded in a 40’ container

NATIONAL G700 14” STROKE DUPLEX MUD PUMP(Ref#8312Ta)  700 HP, 14” stroke, cast iron fluid end, surge chamber, 285 gpm @ 3550 psi with 5” pistons or 805 gpm @ 1265 psi with 8” pistons, mounted on skid 10’ x 23’ with enclosure, sold as is  Price:  $27,500

NATIONAL 5-1/2 X 10” MUD PUMP(Ref#14556Ta)  skid mounted with fuel tank, 471 Detroit diesel engine, 4 speed transmission, all new injectors  Price:  $16,500

NATIONAL C-100 DUPLEX MUD PUMP SYSTEM(Ref#10047R)  National C100 duplex mud pump (currently has 5-1/2” liners), gear end and mud end is in good shape, powered by 671 Detroit engine, 1000 gallon fuel tank capacity, tndem trailer mounted (air brakes), fully winterized enclosure with heater unit, locking doors and parts shelves, stairways and rails, 8” steel suction line/hose/sand screen pot/pole winch for adjustment of suction depth,   Price:  $50,000

IDEAL 5 X 10 DUPLEX MUD PUMP(Ref#9068T)453 Detroit engine (tall, not short), mounted on 5th wheel trailer, new bearings in crane case  Price:  $18,500

PERONI PTO/C TRIPLEX MUD PUMP(Ref#6306R)  110mm (4.331”) bore x 190mm (7.480”) stroke, 5000 psig, 125 rpm, 151.6 gpm, 350 psig, stainless steel flud end, Cummins Big Cam, Model NTC-350, built 1980, Eaton 23-speed manual transmission, Philadelphia Model 13HP-2 gear reducer rated 496 hp ratio 14:1, input 1760 rpm, output 126 rpm, pressurized lubricant system, fuel tank 300 gal, trailer mounted, 11’7”H x 41’4”L x 8’1”W double frame triple axle, king pin to 5th wheel, air brakes and lights, approx. 68,700#, located South America  Price:  $90,000

HHF 500 TRIPLEX MUD PUMP(Ref#2565Tb)   (Hongua International), year 2012, KTA 1150C (19-P750) engine, 6-3/4” cylinder diameter, 7-1/2” stroke, lots of spares  Price:  $150,000

NF-500 (CHINESE MANUFACTURED0 500 hp MUD PUMP(Ref#13723R)  Manufactured 2011, 550 gpm@3000 psi, Cat C15 diesel engine, pulsation dampener, mounted on Galvanized jack-up base, located Australia  Price:  $280,000

SKYTOP BREWSTER 7-1/4 X 14” MUD PUMP(Ref#13399Rb)  379 Cat didsel engine, Matco hi pressure forged steel fluid end, quick change valve heads, Hydril dampener, brand new expendables sill in box  Price:  $59,500

OILWELL DUPLEX MUD PUMP(Ref#1190N)  Rebuilt with all new fluid end parts and rebuilt gear end, Detroit 8V71 diesel engine, mounted on oilfield skid, hand clutch, belt drive, belt guard, pulsation dampener, pressure gauge, pressure relief valve, cleaned and painted, factory specs:

OILWELL 4 X 6 MUD PUMP(Ref#8578T)  New belts, diesel power, new mud end parts, mounted on skid on 8’ x 16’ gooseneck trailer, ready to work  Price:  $28,000

EWS 440 UNITIZED MUD PUMP PACKAGE(Ref#599N)  refurbished Detroit Series 60 engine, refurbished Allison transmission, input horsepower rating 440 max, 320 max pump speed rating, 6” stroke length, 4-1/2” maximum piston size, 3000 psi fluid end working pressure rating, 3” (as required) discharge connection size, 6” (as required) suction connection size, 2” NPT accessory connection size, API#4 valve size, API#S-2 piston rod end, 35 gallon cancase oil capacity, 24 gallons liner wash capacity, internal gear ratio:  4.58:1, 6.517:1.  Price:  $200,000

DRAGON W-440 TRIPLEX 6” MUD PUMP(Ref#7756Ta)  skid mounted on 8’ x 28’ skid, Detroit 60 Series 8 cyl Turbo diesel power plant with 440 hp, on board fuel tank, M310 Series control panel  Price:  $132,500

L & L SMC T135-5 TRIPLEX 6” MUD PUMP(Ref#7756Tc)  mounted on 7’ x 21’ skid, Cat 6 cyl turbo diesel engine, in-line style system, hyd tanks  Price:  $29,500

MCFARLAND P38 PUMP(Ref#3917Ta)  low hours, 1”, 10,000 psi set up, pump can be configured for 18,000 or 25,000 psi, 60 hp electric motor, skidded  Price:  $27,500

FAMMCO TRIPLEX PUMP(Ref#2760T)  2 x SPM 600 HP 10K, 3-1/2 x 6’ stroke plunger, powered by (2) Cat C12 400 hp diesel engines, (2) Allison HT750 trans., (2) 4 x 5 cent pumps, (2) 5 x 6 slurry mixing pumps, 6 bbl mixing tub, 14 bbl averaging tub, mounted on 2002 tandem axle 8’6”W x 50’ step deck trailer  Price on Request

GARDNER DENVER PZ-11(Ref#10748R)  approx. 7000 hours, Cat 3512C (1476 hp), 5000 psi fluid end cylinder, 5-1/2” piston cylinder, antifreeze heaters, WPT W21-CG-300 Type 1 PTO clutch, 16 groove drive sheave, 16 groove bullwheel, 16 groove Kevlar belt with necessary guards, 5 x 6 x 11 charge pump c/w 50 hp@1200 rpm electric motor.  Discharge plumbing: 2” 5M XXH B/W Oteco gate valve, 4” 5M XXH b/w Oteco gate valve, 3” 5M Oteco popoff valve w/1502 connection, 2” 5M type D Oteco mud gauge with 1502 connection, Hydril 20 gal 5M pulsation damper.  Mounted on oilfield skid with separate, with expendables cabinet, knowledge box and removable engine skid for breaking the engine and pump into separate smaller loads.  Winterization package, oilfield lighting, explosion proof starters for charge pump, rod oiler pump and liner wash pumps.  Price:  $695,000 - Make Offer

GARDNER DENVER PZ9 TRIPLEX MUD PUMPS(Ref#7062T) Two Available, each complete with Cat 3508 diesel engines, pulsation dampener, and mud tanks with desander, desilter, etc.  Price for Package:  $110,000

GARDNER DENVER PZ9 TRIPLEX MUD PUMP(Ref#14850R)2 units available, no power, fully serviced to OEM specs in July 2008 and stored since then  Price for both:  $430,000

GARDNER DENVER PZ7 STYLE TRIPLEX MUD PUMP(Ref#1245Nb)  Reconditioned, inspected and tested.  550 hp input, Cat D379PCTA diesel engine (reconditioned), air start, muffler, standard instrument gauge panel, mounted on Cat rails, new 20CB500 air clutch, reconditioned radiator.  Belt drive assembly consisting of pump drive sheave, pump drive belts with belt guard, engine drive sheave, engine drive belts with belt guard, pillow block bearings.  Reconditioned Continental Emsco PD-45 12 gallon 5000 psi WP pulsation dampener.  New O’Drill/MCM ORV 21050 2” 1,000 – 5,000 psi WP shear relief valve.  New O’Drill/MCM 2” 0 – 6,000 psi WP type D mud pressure gauge.  PZ7 fluid modules complete with suction manifold and discharge strainer cross.  New CA-122 liner wash pump, pinion driven with spary nozzle system, water tank and hoses.  New fluid end expendables with 6” liners.  (3) runner oilfield type master skid with loading hitches.  New 5 x 6” R.H. centrifugal 178 series charge pump, 1-7/8 shaft, 10” impeller size, belt driven off pinion shaft, drive belts with belt guard.  New 6” fgure 400 hammer union.  New 4” 5000 psi WP gate valve, new 200 gallon air receiver tank, new air controls.  Price:  $455,000

Fitted with 5" Liner and pistons, bare pump, no extras, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED.

Fitted with 5” liners and pistons with washing and lubricating system, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with a rebuilt Detroit Diesel V1271 w/ Twin Turbo, 550 HP, with a chain case and a manual transmission

Fitted with liner & pistons, with rod washing & lubrication system, bare pump no extra"s, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with New CAT C13 (440 HP) diesel power unit, w/hand clutch, belt drive, belt guard, fuel tank.

Fitted with 5" Liner and pistons, w/washing & lubricating system, THIS PUMP REQUIRES PRESSURE LUBRICATION OF THE POWER END (AUXILIARY OIL PUMP REQUIRED) THIS IS NOT INCLUDED, skid mounted with New CAT C15 (540 HP) diesel power unit, with manual transmission with 4 to 1 gear case, fuel tank.

Manufactured 2008, Cat C-9 new genset, 10 bbl tank, shaker, charging pump, Allison HT750 transmission, 1600 hours, mounted on mobile 52’ trailer  Price: $290,000

GARDNER DENVER PAH MUD PUMP(Ref#7546T)  8V92 Detroit diesel engine, Allison transmission, choke manifold on unit and charge pump, pistons and liners,  Price on Request

MUD KING PAH MUD PUMP(Ref#12669T)  Detroit Series 60 engine, Allison 750 transmission, 3” centrifugal pump, 90 bbl 2-compartment circulating tank  Price:  $290,000

GARDNER DENVER TRIPLEX MUD PUMP(Ref#8245Rb)  Completely rebuilt, new paint, skid mounted, new Detroit 671 engine 165 hp @ 1800 rpm, new fuel tank, lines and fluid end, multi speed transmission and clutch, 12 volt DC starting and operating system, 5” suction, 1742 to 10,000 psi discharge pressure, 8 – 138 gpm capacity, full functional control panel, mounted on oilfield skid, dims 240”L x 90”W x 60”H 12,000#  Price:  $39,500

KERR 2200 AND 3500 OR FMC M1214 TRIPLEX MIST PUMPS(Ref#7999T) Cat engines, 4 speed transmissions, rigged up with secondary containment, onboard lighting, winterization canvas for cold weather operations, Also available with Cummins or John Deere engines Priced from $77,500 to $97,500

GARDNER DENVER PQ172 TRIPLEX MIST PUMP(Ref#7827Ta)  Deutz F3L914 45hp 3 cyl air cooled diesel engine with electric start, manual transmission, gauges, 4’H x 4’W x 7.5’ long, 3” hardline, 22 bbl mixing tank, skid mounted  Price:  $17,500

GARDNER DENVER GXP TRIPLEX 6 X 16 MUD PUMP(Ref#11010T)  Skid mounted, twin Detroit 671 diesel engines, 30 ton, dimensions: 28’L x 11’W x 8’H   Price:  $32,500

GARDNER DENVER GXR 800 HP DUPLEX MUD PUMP(Ref#12423Rb)  Matco steel fluid end, pulsation dampener, fuel tank, gauges, controls, starter, mounted on oilfield skid, completely rebuilt engine and fluid end  Price:  $125,000

GARDNER DENVER FXN 7-1/4 X 14 MUD PUMP(Ref#1403T)  Cat 3408 engine air start with pump drive and belt guard, PD55 Hydril dampener, 750 gallon fuel tank, mounted on heavy duty drop deck tandem trailer,  low hours  Price:  $87,500

GARDNER DENVER FXN 7-1/2” X 14” DUPLEX MUD PUMP(Ref#8312Tb)  500 hp, on skid with Cat D343 engine, capable of 200 gpm @ 3000 psi with 4” pistons or 775 gpm @ 940 psi with 7-1/2” pistons, sold as is  Price:  $27,500

GARDNER DENVER FXN 7” X 14” DUPLEX MUD PUMP(Ref#6637Ta)Forged steel fluid end, quick change caps, Cat 3412 diesel engine, Hydril K20 3000 pulsation dampener, Demco 2” relief valve, belt drive, type F3000# pressure gauge, rod oiler pump, speed sensor, electric start, air clutch, skidded with roof, 3-1/2” x 20’L vibrating hose  Price:  $76,000

GARDNER DENVER FZ-FXZ MUD PUMP(Ref#4087Tb)  7-1/2 x 12, Tier 1 Detroit diesel 60 Series, 12.7L 500 hp, good gear and fluid ends, same-trailer mounted, 500 gal fuel capacity  Price:  $90,000

GARDNER DENVER FXZ 6-1/2” X 12” MUD PUMP(Ref#10287Tb)  Detroit 8V71 engine, hauled on 3 axle skid trailer with 1989 TTRAC International truck  Price:  $69,500

GARDNER DENVER FXN DUPLEX MUD PUMPS(Ref#8214R)  Two available, 14” stroke, 2” rod size, 400 hp, 75 strokes per minute, cast fluid ends, unitized on oilfield skid with Cat 3406 diesel engines, air start, new filters, oil and coolant, air receiver on deck, fluorescent lighting, drive belts with air clutch.  Gone over and in good operating condition, ready to be put into service.  Pumps currently have new 6” liners with production being 480 gpm @ 1000 psi.  All fluid end parts are brand new and never used, including the valves, gears, liners, pistons, rods, head gasket, and rod packing, equipped with pulsation dampener.  32’ long x 11’ wide x 7’ high 50,000# weight  Price:  $72,500 each

GARDNER DENVER FXZ 7 X 12 MUD PUMP(Ref#6602RD) only 1300 hours on new 12 Liter Volvo engine, air clutches, skid mounted, 20’L x 9’7”W x 8.4”H, 40,000#  Price:  $45,000

GARDNER DENVER 5-1/2 X 8 FXN DUPLEX MUD PUMP(Ref#6678T)  Cast fluid end, 671 Detroit, Spicer 6853-C transmission, hydraulic pump, air controls, 1” hyd hoses, skidded  Price:  $44,500

GARDNER DENVER 5 1/2 X 10 MUD PUMP(Ref#3261Rb)  6 cylinder Cummins diesel engine, hand clutch, 5 speed transmission, 5-1/2” liners, skid mounted, 10” stroke, ready to work  Price on Request

GARDNER DENVER 5 X 10 MUD PUMP(Ref#1480Tb)  air driven, used with cement for grouting wells, sitting 3-4 years, valves will need rebuilding, trailer mounted, air over hydraulic brakes, includes 28 joints of 21’ pipe  Price:  $39,500

GARDNER DENVER 5 X 10 MUD PUMP(Ref#5882Tb)  453 Detroit engine, battery start, mounted on oilfield skid with axles, starts and runs  Price:  $14,500

GARDNER DENVER FDFXDH MUD PUMP(Ref#14457T)  4” inlet, 3” outlet, pulsation dampern, new piston and rods, engine has been removed    Price:  $40,000

5-1/2 x 8” GARDNER DENVER MUD PUMP(Ref#4523N)  Manufactured 1960’s, rebuilt a couple years ago, skid mounted, 4 cylinder Detroit engine, used Supercharger, 637 hours on it, runs good, needs cosmetic work  Price:  $32,500

GARDNER DENVER 5 X 6 MUD PUMP(Ref#302Tb)  2 available, unmounted, rebuilt pumps, need normal expendables (neoprene is old in the valves etc)  Price:  $17,500

GARDNER DENVER FG-FXG 5 X 6 MUD PUMP(Ref#3510R)  Detroit diesel engine, mounted on tandem axle trailer, one suction and one discharge hose included  Price:  $39,500

GARDNER DENVER 5 X 6 MUD PUMP(Ref#13203T)  electric drive, in custom skid, fully rebuilt gear end and fluid end, excellent condition  Price:  $22,500

GARDNER DENVER FXF-DE8 4 X 5 MUD PUMP(Ref#10148T)  Manufactured 1996, new condition of gear and fluid ends, no engine, new 4” liners, new pistons, new chrome rods, new valves, new liner studs in head, new suction flange and gasket, new 2” steel discharge flange  Price:  $13,500

4 x 5 GARDNER DENVER PISTON MUD PUMP(Ref#7097Rb)  bull wheel or can be connected to hydraulic motor, 75% condition, needs some work  Price:  $5,500

GARDNER DENVER 5 X 6 HYDRAULICALLY DRIVEN MUD PUMP(Ref#2505T)  approx. 2500 hours, unmounted, (taken off a rig), fluid ends have not been rebuilt  POR

GARDNER DENVER PE5U 4X5 TRIPLEX MUD PUMP(Ref#11077c)  powered by Cat 3306 diesel engine, Eaton 5-speed transmission, manifold, enclosed building  Price:  $72,500

GARDNER DENVER PE5 TRIPLEX MUD PUMP(Ref#4692Ta)  Detroit 6V71 engine, electric start, radiator, 2” Shear relief valve, Spicer manual transmission, skidded  Price:  $25,000

GARDNER DENVER TEE PUMP(Ref#1654T)  Manufactured 1998, 1602 hours, 4" plungers with hydraulic charge pump, Detroit Series 50 (rebuilt), 5 speed, Skid mounted with fuel tank, Rebuilt expendables with seals, valves, seats, packings and gaskets.  Price:  $72,500

GARDNER DENVER TEE MUD PUMP(Ref#6440T)  New, unused, manufactured 2014, 4 available, bare pumps  Price:  $39,500 each  New Cat C7 engines available at additional cost

GARDNER DENVER TEE 4 X 5 TRIPLEX MUD PUMP  **NEW**(Ref#9115R)  4” piston and liners, well servicing valve and seats, bare pump, extras a extra cost, 2 available (1 plunger and 1 piston)  Price bare pump:  $64,000

(1) NATIONAL C250 DUPLEX MUD PUMP7-1/4 x 15”, New fluid end parts, bolt on valve cover, Rebuilt gear end, Pulsation dampener, new Cat C15 diesel or 12V71 diesel engine, Electric start, Controls, gauges, safety shut off, Master skid   Price with Cat engine:  $135,000   Price with Detroit engine:  $120,000

GARDNER DENVER FXK 7 1/4 x 14” DUPLEX MUD PUMP  New fluid end part, Rebuilt gear end, Detroit 12V71 diesel engine, Electric starter, Controls, gauges, Safety shut off   Price:$80,000

(2) NATIONAL C-150 DUPLEX MUD PUMP 6 ¾ x 12”  250 gpm / 550 PSI, New fluid end part, Rebuilt gear end, Pulsation dampener, Detroit diesel engine, Electric start, Controls, safety shut down, Master skid  Price:$80,000   6 weeks delivery

7” x 12” WHEATLEY DUPLEX MUD PUMP  (rebuilt), Model 27-12, powered by rebuilt 671 Detroit diesel engine, rebuilt gear end and fluid end, with all new fluid end parts, hand clutch, pulsation dampener, rod lubricating gland, pressure gauge, pressure relief valve, belt drive, belt guard, fuel tank, battery start, mounted on oilfield skid, cleaned and painted, guaranteed for 6 months, delivery 12 weeks after order  Price:  $42,000     Delivery 12 weeks

CENTERLINE 7-1/2 X 10 MUD PUMP(Ref#14556Tb)  high pressure, no engine, needs retaining liner cage and (1) side suction manifold needs replacing, unmounted  Price:  $39,500

CENTERLINE MODEL CLM 7-1/2” X 10 MSPA, 7-1/2 X 10 MUD PUMP(Ref#10877T)  Manufactured 2017, 150 GPM, 400 PSI, Centerline Mono, used for one job to go to 200’ to pump water, unmounted, no engine, like new condition  Price:  $26,500

WHEATLEY 5 X 10 MUD PUMP AND KING SWIVEL(Ref#1557Nm)  20 bbl tank, mounted on gooseneck double axle dual tires trailer, 1995 International single axle tractor, hoses, hydraulic valves and hoses  Price:  $95,000

CONTINENTAL EMSCO D500 DUPLEX MUD PUMP(Ref#5074Tb)  Trailer mounted, Detroit Series 60 diesel engine 14L, 40’ tandem axle trailer with hydraulic leveling jacks, currently working  Price:  $87,500

EMSCO D500 DUPLEX MUD PUMP(Ref#6329T)  16” stroke, 500 hp, ductile iron fluid end, Cat D353 diesel engine with radiator, 640 hp, 1300 rpm, inline 6 cylinder, 4 stroke, 6-1/4” bore x 8” stroke, (1473 in3) displacement, turbo charged (air to air aftercooled) aspiration, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons.  Price:  $37,500

EMSCO D500 DUPLEX MUD PUMP(Ref#6118Rh)  Emsco D500 duplex mud pump with steel fluid end, Hydril K-20-3000 pulsation dampener, belt driv with Cat D379 diesel engine, air starter, radiator, air clutch, mounted in 12’ x 29’L mud pump house with parts bin, controls  Price on Request

EMSCO D500 DUPLEX PUMPS(Ref#8722R)  Two available, Cat 3406C diesel engine, Cotta gear box, mounted in enclosed building 11’6” x 30’  Price:  $70,000

EMSCO D500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Tc)  500 hp, Mounted on skid with Cat D353 engine, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO D500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Td)  500 hp, Mounted on skid with twin Detroit engines, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO DA-500 4-3/4 – 7-1/2” X 16” DUPLEX MUD PUMP(Ref#8312Te)  500 hp, Mounted on skid with Cat D353 engine, capable of 268 gpm @ 2720 psi with 4-3/4” pistons or 751 gpm @ 970 psi with 7-1/2” pistons, sold as is  Price:  $27,500

EMSCO D-300 6 X 14 DUPLEX MUD PUMP(Ref#3360Tb)  Excellent condition, skid mounted on tandem axle heavy duty lowboy trailer, fluid end rebuilt with new 6” liners, liner cages, piston rods, swabs, rod packing, oiler pump, new Mattco end plug, Detroit 8V71 engine (good condition)  Price:  $44,500

CONTINENTAL EMSCO D175 7 X 12” MUD PUMP(Ref#12068Nb)  powered by 8V71 Detroit engine, flued end and engine rebuilt, all new expendables, junk box, fuel tank, air compressor and air clutch, skidded.   Price:  $100,000

EMSCO D300 DUPLEX MUD PUMP(Ref#8210N)  7 1/2 x 14, Matco steel fluid end with screw off caps, Cat 3406 diesel powered, Air chamber, Spare fluid end parts, Air start, Fuel tank, On oilfield skid, Mounted in an 11’ wide metal building, Good condition   Price: $120,000

GASO5885-WS  QUINTUPLEX PRODUCTION PUMP(Ref#10309T)  Pump only.  5” stroke, 300 hp, steel billet fluid end, 2-3/4” ceramic plungers, Delrim disc valves, 838 packing, 6” RF suction connection, 3” RTJ discharge connection, 231 gpm max, 2020 psi, max 360 rpm  Price:  $82,500

GASO 3364 MUD PUMPS(Ref#9104T)  Two available, rebuilt, cast ductile iron fluid ends, used for oil service, bare pumps, no engines, unmounted, one is flanged for suction/discharge, one is threaded  Price:  $20,000 each

GASO 1860 4-1/2 X 6 MUD PUMP(Ref#14394T)  Fluid end completely rebuilt, powered by 3 cyl Deutz diesel engine, trailer mounted, hoses and misc parts  Price$19,500

GASO MODEL 1742 5 X 10 MUD PUMPS(Ref#3276Rb)  John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank w/lock cap, Dayton oiler pump systemand tank, 4” suction hose and winch boom, 4’ back up bumper guard, front and rear loading hitches, 44” bullwheel with power band belt, large belt guard, 8’ x 17’ base (mud boat)  Price:  $62,500

GASO 1742 MUD PUMP 2-1/2 to 5 X 10(Ref#2412Ta)  Cummins 150 hp reconditioned engine with snap-in clutch, 90 gal diesel tank with lock cap,  Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ back up drill pipe bumper guard, front and rear loading hitches, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard  Price:  $82,500

GASO MODEL 1654 MUD PUMP(Ref#6937T) 5 x 8, drive shaft included, new gears and bearings 2019, new pistons and piston sleeves 2021, new valve rubber inserts and valve cup gaskets 2022, very good condition  Price:  $18,500

GASO 1550 MUD PUMP 2-1/2 TO 5 X 10(Ref#2412Tb)  Detroit 671 engine with Snap-In clutch (Gen Set approx. 1500 hours),  replaced fluid end parts with 4” liners,  mounted on 8’ x 12’ trailer with adjustable pintle and DOT lighting, 75 gal diesel tank with lock cap, Dayton oiler pump system and tank, 4” suction hose and winch boom, epoxy primer and enamel paint, 44” bull wheel with power band belt, large belt guard, 2’ x 2’ x 5’ lockable HD toolbox, mouting beams and steel/bolts  Price:  $41,500

GASO 5 X 10 MUD PUMP 1742(Ref#4047Rc)  8’ x 17’ base (mud boat), John Deere 145 hp reconditioned engine with WPI snap in clutch, 90 gal diesel tank, Dayton oiler pump system and tank, 4” suction hose and winch boom, 4’ backup drill pipe bumper guard, front and rear loading hitches, 42” bull wheel with power band belt, belt guard    PRICE:  $73,500

GASO T4507 TRIPLEX MUD PUMP(Ref#999Nb)  Triplex single acting reciprocating plunger pump, 450 hp, reconditioned rental package, aluminum bronze fluid end with 5-1/2” plungers, 642 gpm@ 1095 psi, new AR valves (3/09), Cat 3406 engine,  260 rpm, max GPM 1039, Max PSI 1200, skid mounted, coolers, controls, gauges  Price:  $175,000

5x10 GASO MUD PUMP AND TANK SYSTEM(Ref#240N)  350 gpm @ 330# psi, skid mounted trailer w/6V71 Detroit diesel engine, shale shaker 4 X 5 Schrem, 1000 gallon tank, (2) desanders, hydraulic motor on mud pickup pump  Price:  $65,000

AMERICAN DUPLEX MUD PUMP  - NEW(Ref#14063N)  Model AXG (FG-AXG), capacity (with 5” liners) 200 gpm (757) x 310 psi (21 kgcm2), @ 100 rpm, bare pump, no engine  Price:  $25,000

UNION T68 TRIPLEX MUD PUMP(Ref#999Na)  Triplex single acting reciprocating plunger pump, 6” plungers, 405 hp, 4.95:1 gear ratio, powered by 8V92T Detroit diesel engine and transmission, 617 @ 1061 psi at 210 rpm, Max GPM 620, Max PSI 1060, skid mounted, cooler, controls, gauges  Price:  $130,000

1600 HP F1600 TRIPLEX MUD PUMP(Ref#1401N)  Made in China, electric motor, Model HHF1600, triplex single acting piston type, 7” x 12” max diameter of liner stroke, 120 spm, 1176kW (1600hp) rated power, gear ratio 4.206, 12” stroke of piston, pump valve API 7#, 7” max ID of liner, max working pressure 34.3 MPa (5000 psi), max displacement (130 s/min) 50.42L/s, diameter of discharge pipe 127mm (5”), diameter of suction pipe 304mm (12”), weight 25570kg (56,000 lbs).  combined v-belt transmission 800 kw (1072 hp) * 2, 25 (J)-5-7630 V-belt, transmission ratio 2.377, Model YZ08 motor 800kw, 60 hz, Model SB6”  8” J-12 1/2” charging pump, 8” diameter outlet, 6” diameter inlet, 200m3/h displacement, 55kW power of centrifugal motor  Price:  $425,000

BOMCO SJF-1600 MUD PUMP(Ref#9621R)  1600 hp, 12” stroke, 5000 psi, pulsation dampeners, pop off pressure release valve, pump pressure gauge, forged discharge manifold, overhead track for chain hoist, mounted on shipping skid, line washer pump, 6” liners, overall size:  192 x 128 x 105-3/4”, inspection report available, 4 available    PRICE:  $137,500 each

BOMCO F-1600 MUD PUMPS(Ref#6252T)  2 available, Built 2007, powered by 1500 hp GE traction motor  Model GEB29-A1, 5k fluid ends with pulsation dampener, liner washer pump and external oil pump, on a master skid with roof  Price:  $162,500 each

QINGZHOU ORF 1000 HP MZ-9 MUD PUMPS(Two Available)  (Ref#2798R)  Manufactured 2007 and 2008, 7” x 9” 1000 hp triplex mud pump, 5000 psi pulsation dampener, 5-star 5x6 centrifugal pump 50 hp electric motor, suction screen, centrifugal rod oiler, (2) 2005 Detroit diesel 560 14L 665 hp w/ zero hours, electric start, radiator, gauges, Wichita power grip clutch, all master skidded  Price:  $255,000

CONTINENTAL EMSCO MODEL FC2200 TRIPLEX MUD PUMP(Ref#2280T)  Complete without traction motors.  9” bore x 15” stroke, single acting, working pressure up to 7500 psi, (3) interchangeable forged steel fluid end modules with separate suction and discharge sections, Premium grade fluid end expendables with 6-1/2” pistons and liners, suction manifold with (3) 12” flanged inlets, SD8 suction desurger, pressure manifold with (2) 5-1/8” 10,000# API flanged outlets, liner wash system, 1 x 1-1/2” mission centrifugal pump p/b 3 hp electric motor, external power end lubrication pump, steel skid, suction line pressure relief valve, set of standard service tools  Price:  $675,000

EMSCO STYLE F1000 TRIPLEX PUMPS(Ref#9886T)  2 available, 6-3/4” liners with 644 gpm @ 2380 psi, belt driven charging pump, pulsation dampener, with 398 Cat engines, skid mounted, ready to work  Price:  $112,500 each

-The unitization includes an electric motor powered supercharging pump piped to the suction of the mud pump, an electric powered liner wash pump mounted and piped, engine and WPT power grip 321 controls at area of engine arrangement, industrial coating on all parts and labor to clean & make ready for shipment.

-Pump suction manifold is 12”, and intake flange diameter is 12”. A 12” valve is used in suction manifold. And two suction solutions are alternative, pump charging and self-suction.

-F-1000 mud pump is driven by diesel engine (Caterpillar 3512DITA, 1250 HP @ 1200rpm) through WPT power grip 321. The unit is complete with a bull wheel, a set of V-belts, belt guard, a drive assembly and screw devices for tightening belts.

-The unitization includes an electric motor powered supercharging pump piped to the suction of the mud pump, an electric powered liner wash pump mounted and piped, engine and WPT power grip 321 controls at area of engine arrangement, industrial coating on all parts and labor to clean & make ready for shipment.

-Pump suction manifold is 12”, and intake flange diameter is 12”. A 12” valve is used in suction manifold. And two suction solutions are alternative, pump charging and self-suction.

EWCOWH-600 TRIPLEX MUD PUMP(Ref#1183N)  Manufactured 1984, good condition, powered by (2) Cat 3408 engines, mounted on oilfield skid, located Southeast Asia, immediately available  Price:  $190,000

NEW CONTINENTAL EMSCO STYLE F-1000 TRIPLEX MUD PUMP(Ref#1287N)  triplex single action piston, max. liner size x stroke 170 x 254mm (6-34” x 10”), 140 r/min strokes rating, 753kW (1000 hp), Herringbone gear, 4.207:1 gear ratio, pressure and splash lubrication, 12” flange suction inlet, 5-1/8” flanger 5000 psi discharge outlet, 7-3/4” pinion shaft dia., 2” x 2” key, valve-over-valve API#6, approx weight 41,420 lb, fully interchangeable with Continental Emsco parts, complete with pulsation dampener, suction discharge, pressure gauge, complete fluid end expendables, guaranteed for one year, delivered to Houston from China factory,  2 available  Price, delivered to Houston:  $185,000 each      (30% deposit with order, balance due when shipped from China)

CONTINENTAL EMSCO F-800 TRIPLEX MUD PUMP(Ref#664T) 800 hp, 6-3/4”, forged steel fluid end, 50003 pulsation dampener, 3” Shear relief valve, skidded  Price:  $37,500

OFM600 TRIPLEX MUD PUMP(Ref#2497T)  Manufactured 2018, 1800 hours, very excellent condition, Detroit 60 Series engine, Allison transmission, 800 psi, dims/weight 20’ x 10’ x 8’, 20,000 lbs  Price:  $320,000

AXON HD-500 TRIPLEX PLUNGER PUMP(Ref#975T)  14 liter Detroit Diesel, 6061 Allison automatic transmission, rebuilt power end, new expendables in fluid end, new charge pump, skid, tanks, Pilfer 5 valve manifold, 15k fluid end, new paint  Price:  $215,000

WHELAND DUPLEX MUD PUMP(Ref#7936)  7-1/2 x 14”, Hydril K-20 pulsation dampener, Cat D342 diesel engine, 300 bbl 3-compartment steel mud pit with (2) 7.4 hp electric mixer motors  Price:  $55,000

FMC BEAN PUMP MODEL L1122DI(Ref#3916T)  122 hp, 91 kw, 1750 max rpm, 127 gpm, 519 lpm, 1300 psi, 9063 kpa, Baldor ECP4409T 100 hp motor, 1200 rpm synchronous speed, 60hz frequency, 460V (3P)  Price on Request

HYDRAULIC PUMP WITH KUBOTA ENGINE(Ref#5073T)  Lofa Industries hydraulic pump (6.2 hours) with Kubota V3800T engine, Hydac ELD cooling system  Price:  $24,500

Bean 35 mud pumps(Ref#7739R) completely rebuilt, skid mounted with Deutz diesel engine, 4 speed transmission, low 50 hours, stored inside   Price:$14,000

OILWELL C338H TRIPLEX WATER INJECTION PUMP(Ref#6530T)  3” plungers, 3540 psi max pressure, 336 hp @ 200 rpm input, Cat G3408 gas engine, Falk gear/transmission, 100 rpm input, 290 rpm output, ratio 3.793:1, service factor 1.98, 375 hp Price on Request

SPRAGUE SYSTEM 0-55 GPM, 3500 PSI DUAL SYSTEM PORTABLE TURBO DIESEL HYDRAULICPUMP  (Ref#9235R)  New Unit.  High pressure, low volume, self-contrained.  Capable of 5000 psi intermittent duty, designed for low maintenance and flow operation.  A single adjustable back pressure regulating circuit allows operator to adjust aircraft reservoir return condition and maintains a positive reservoir head pressure on the aircraft without fluid loss.  This feature allows the system to be used on drilling rigs with different reservoir pressure requirements.  Lighted control panel.  Automatic over temperature shut down, Reservoir high/low level automatic shutdown, Safety circuit boost pump pressure switch, loss of boost pump pressure automatically shuts system down, Phase reverse relay (does not allow pump to turn in wrong rotation), Automatic air removal device (this removes the air from the oil returning from the rig at flows up to 55 gpm automatically; results are no cavitation, longer pump life, quiet system.  Reservoir drain valve, Parking brake instrument panel lights 100 hp drive motor (Deutz 125 hp), International Reservoir and system fluid emperature indicator.  Chassis has a 2-wheel mechanical parking brake.  The lower portion of the chassis serves as f ull sized drain pan with drain valve.  Cabinet is skydrol resistant stainless steel.  Removable cover assembly for major maintenance with access doors for inspection and minor maintenance.   Price:  $185,000

TEST PUMP RIG(Ref#3417T)  Mounted on 12K GVRW trailer, hydraulic powered spool with approximately 500 of 2” hose, internally routed power and safety cable, 7.5 HP pump and motor, Whisper Watt 25kva 3-phase diesel generator with approx. 3100 hours  Price:  $45,000

HYDROPLEX 15K TEST PUMP(Ref#2496R)  Manufactured 2012, 15 gallons per minute, mounted on 2008 GMC C6500 truck with diesel engine, control box, manifold, 550 gal heavy duty Snyder Megatainer tank, 123,896 miles on truck  Price:  $85,000

SCHAEFER & URBACH BT 80-120 GERMAN MANUFACTURED TRIPLEX MUD PUMPS, POWERED BY AC MOTOR AND GEAR DRIVEN(Ref#6853N) 3 available “LIKE NEW”– Manufactured 2006, Speed Max/Count: 135 SPM, 220 bar – 350 bar (5000 psi), Max. Displacement 4,005 l/min at 150 bar, Max. pressure 1,565 l/min at 350 bar, Elin 6 AC Motor, 690V/75 Hz, 1000 KW, Mounted on skid 8100 mm long x 3000mm wide x 2960 mm high. 45,000kg, Sound level: 63dB(A)@ 7 meters, Operating hours: (1) 1668, (2) 1010, (3) 2069, NOV Mission Magnum 8 x 6 x 14 charge pump, Amtec 36 kw AC Motor, 400/690V/50Hz, NOV Mission Magnum 3 x 2 x 13 liner cooler pump, 2,2 kW AC Motor 400/690V/ 50 Hz, Hydrill K20 pulsation dampener, Zollern gear / mud pump, Located in Europe

MUD PUPPY MP-255(Ref#1065T) Mounted in 16" trailer with 3 stabilizing jacks, sand guzzler, 3 x 2 centrifugal pump needs replacing, 3100 hours, includes 4" hose for pick up pump  Price:  $49,500

MUD PUPPY 2000(Ref#7953T)  Manufactured 1999, 1000 gal holding tank, (2) 3 x 4 Mission Magnum pumps with mechanical seals, MC255-2C mud cleaner, sand guzzler, Versa-drill rig jacks, Perkisn engine, spare hyd pump and filters, well maintained, ready to work  Price:  $59,500

CUSTOM BUILT MUD PUPPY(Ref#6133Ta)  800 gallon capacity, mounted on Big Tex trailer, 2” x 4” screen, 200 gpm, manual jack, no engine – runs off rig   Price:  $25,000

MUD PUPPY MUD SYSTEM(Ref#3572R)  3 x 2 Baker centrifugal pump, powered by 3 cyl Lister, Mud Puppy pick up pump, hydraulic power pack, barrel shaker, desander, dual 2000 gal mud tanks, mounted on gooseneck trailer  Price:  $60,000

MUD MIXING SYSTEM(Ref#430N)  Manufactured 2004, Mud Puppy, Deutz diesel engine,  dual shale shaker, down hole centrifugal pump, mud mixing pump, 1000 gal capacity, 500 gpm system   PRICE: $112,000

2000 GALLON SHOP BUILT SHALE SHAKER(Ref#15419Tc)  5 x 8 screen, 3 x 4 mission centrifugal pump, desanding cones, 300 gpm pickup pump, 2009 Cummins 110 hp motor with 7,150 hours, mounted on 3 axle trailer  Price:  $19,500

MUD PUPPY 170-2SC(Ref#5864Ta)  Deutz diesel engine with brand new turbo, 3 cone manifold, new style hydraulic Parker pump and new style shakers, newer 118 pump, trailer mounted  Price: $55,000

MUD SYSTEM(Ref#13092T)  2200gal Split wall tank, Twin Cummins 3.9 deck, W/3"-4" centrifugal mixing ,desilting, agitation pump . Mechanical Seals, 5.9 Turbo @2500 rpm W/3"x4" Chrome centrifugal down hole pump. Mechanical Seals desanded return with cross tank flow back flange (For sudden fluid loss), Twin 4"x5" hydraulic shaker dual screen deck, 4 Jack hydraulic leveling system. 27000GVWR tandem axles w/electric brakes . trailer can be legally pulled in NV safety by 1-ton . Brakes are excellent. @20000.GVW, Hydraulic ports for Tibban type mud return sump pump . In tank cooling.  Unit capable of 1000"x 24" drill bore with 3-1/2IF Drill string. Using open jet Tricone or similar. Unit is ready    Price:  $77,500

EDGE MUD CONDITIONER(Ref#5510RC) 600 gpm, 2 shale shakers, 1 400 gallon trash pump (1 more optional), 4 desander cones, 1 desander “Cobra” circulating pump, pintal hitch, air brakes, tank and system like new (low hours), 1200 gal tank, 4 hyd leveling jacks, tandem axle, Deutz 3 cyl air cooled diesel engine and hydraulic pumps in a removable pad,   Price:$65,000

MCT500 MUD MAN MUD SYSTEM(Ref#844R)  Manufactured 2007, rebuilt 2 years ago, 3300 gal 2-section tank, mounted on heavy duty trailer, 480 volt/3 phase, diesel generator, 500+ gpm capacity, 5” desilter cone bank, leveling jacks  Price (without generator)  $115,000  Price with generator:  $130,000

8400 GALLON/200 BBL MUD MIXING SYSTEM(Ref#14692T)  Swaco shaker, 3 centrifugal pumps, Detroit 235kw generator, mounted on 2008 tri axle step deck trailer  Price:  $137,500

MUD TECHNOLOGY MCT-450 MUD SYSTEM(Ref#7707T)  Built 2021, trailer mounted, 100 hp John Deere diesel engine, 100 kw generator fully enclosed, 4 hydraulic leveling jacks, (2) 3 x 4 centrifgual mud pumps with mechanical seals, 3000 gallon 2-section tank with mud guns in the tank, excellent condition  Price:  $187,500

MCT-450 DRILL FLUID MIXING AND CLEANING SYSTEM(Ref#3602T)  Built 2019, 156 hours, 2400 gal capacptiy two section tank, split equally for clean and dirty volume.  High G-force linear shaker, 18 sq ft shale shaker screening area, 18 sq ft desilter screening area, 36 sq ft total screening area with long runway, (6) 5” cones, 450 gpm cleaning capacity.  25hp 178 Series electric centrifugal pump to pressure feed hydrocyclones, 30 hp 178 series electric centrifugal pump to pressure feed hopper, jet guns and supercharge.  480 volt/60kw/3 phase diesel generator, safety shutdowns on engine and generator.  High shear/low pressure mixing hopper, sack table, high shear submersed jet guns in both tanks, independent valves to isolate hopper and jet guns, mounted on 12k dual tan axle trailer, pintle hitch, electric brakes, 24’L x 8’4”W x 12’4” H – 20,140 lbs.  Price:  $172,950

MUD TECHNOLOGY RST-990 MUD MIXING AND CLEANING SYSTEM(Ref#3444T)  1000 gal (approx.) 2-section tank, H G-force linear split shaker, centrifugal pump for mixing and desander, 480 volt/3 phase generator, 320 gpm cleaning capacity  POR

Gardner Denver mud pump rated at 1.7M/3 min @215 bhp with conventional heads, pulsation chamber, Odrill relief valve, 3.0” mud valve, exhaust fan, mixing hoper, liner wash pump and lubricator, driven by Eaton hydraulic pump with gear reducer and rubber block gear box. Pump house fitted with core bench, storage cabinets, insulated, fluorescent lighting, electric heat, 20 M/3 four compartment mud tank, electronic float levels, Tsunami sump pump, Mission 4x3 pre-charge pumps, Derrick FC-313M liner motion shale shaker with super G agitator. All ancillary equipment hydraulically driven off Funk rubber block four pump adaptor powered by C15 Cat engine rated at 540 HP @ 1800 RPM. Aluminum 1500 liter hydraulic tank. Operators cabin – heated, AC, swivel operators chair, deck/spot lights, full instrumentation, audio/video monitoring system, roof beacon, Retractable stairway. Aluminum fuel tank. Self-leveling deck. Pontoons 6’ X 6’ X 38”, four compartment, aluminum cleats, 5.0” chain.

EDGE DRILLING PS750 MUD RECYCLER/AIR CONTAINMENT SYSTEM  (Ref#2642T)  Brand new, never used, 750 gallon tank, 74 hp Tier 4F/Tier 5 European Hatz water cooled diesel engine, 3 x 5 double screen shaker bed, 3 x 4 centrifugal pump, 4 desander cones, with powder coat finish

MUD TECHNOLOGY MC-160 MICRO