quick fill mud pump free sample

The LEVEL5 Quick Release Compound Pump is made from lightweight anodized aluminum with a corrosion-resistant red finish to withstand more than 250,000 cycles without maintenance or repair. Used to fill automatic taping and finishing tools, this compound pump is designed to be an essential part of the drywall finishing arsenal with its quick-release latches and pins for easy assembly/disassembly when cleaning.

Design features include a composite urethane cup seal which lasts 50% longer than traditional rubber seals. It also comes with a FREE Box Filler Valve which is extra-long and compatible with mud pumps by other leading brands.

The 2,200-hp mud pump for offshore applications is a single-acting reciprocating triplex mud pump designed for high fluid flow rates, even at low operating speeds, and with a long stroke design. These features reduce the number of load reversals in critical components and increase the life of fluid end parts.

The pump’s critical components are strategically placed to make maintenance and inspection far easier and safer. The two-piece, quick-release piston rod lets you remove the piston without disturbing the liner, minimizing downtime when you’re replacing fluid parts.

What"s equally as important as your automatic taping and finishing tools? You need a reliable mud pump. The drywall compound pump, or mud pump, is necessary to quickly fill your automatic tools such as a flat box or automatic taping tool, and keep the job moving with minimal delay. Without a reliable pump, you’ll be spending more time fiddling with a pump that is difficult to clean, or worse, resorting to hand-filling your tools, which is time consuming, and counter productive.

No pump = no tools, so you need a workhorse that will withstand a lot, and get through your workday, every time. TheLevel5 Drywall Compound Pumpis constructed of billet aluminum, making it much stronger, and more durable than your typical cast aluminum construction.

Another important quality is resistance to corrosion. Tools built of poor quality and materials are prone to rust and corrosion. The anodization on the Level5 Drywall compound pump makes it highly resistant to corrosion, as well as wear and tear!

A good seal is important too! Typically for compound pumps, a rubber seal is used, but the problem with rubber is that it will slowly deteriorate, and before you know it, you’re leaking all over the place. The Level5 Drywall Compound Pump uses a composite urethane cup seal, which provides much longer wear life vs. the traditional rubber seals.

Working with mud can be messy, and when you’re on the job, it"s important to be able to easily clean and maintain your compound pump. You should not be spending any extra time fiddling with small screws or components to clean your pump, or to switch valves.

That’s why the Level5 Compound pump has easy clean features, like grenade pins and easy-release latches on its tube and handle. It also comes with a wrench, and a built-in wrench mount so that you are always prepared to switch from gooseneck to box-filler valve, or make a quick adjustment with ease.

Theoretically, yes you can, but it"s a slow process, and at which point you may be better off hand finishing, as you will impede the speed of the work. The combination of your automatic tools and your mud pump will pay for itself fairly quickly by the speed and quality job that you can achieve.

We think the Level5 Drywall Compound Pump is the best drywall mud pump on the market, and truly the underestimated workhorse in the arsenal of any professional drywall finisher. LEVEL5’s drywall compound pump has been made to meet finisher’s demand for reliability, affordability and workability. This beast of a taping tool is built to withstand years of heavy use. In fact, the Level5 compound pump has been tested for over 250,000 cycles without the need or repair, or replacement parts.

If you’re interested in purchasing a compound pump, you can find more information here. And as always, feel free to email, or give us a call and we’d be happy to provide more information!

A well-placed suction stabilizer can also prevent pump chatter. Pump chatter occurs when energy is exchanged between the quick opening and closing of the reciprocating pump’s valves and the hammer effect from the centrifugal pump. Pump isolation with suction stabilizers is achieved when the charge pumps are isolated from reciprocating pumps and vice versa. The results are a smooth flow of pumped media devoid of agitating energies present in the pumped fluid.

Dedicated to strict quality management and thoughtful client services, our experienced staff customers are generally available to discuss your demands and guarantee full client pleasure for Slurry Sewage Pump, Pump Centrifugal, Diesel Engine Centrifugal Pump, We imagine we"ll become a leader in building and producing high quality products in equally Chinese and international markets. We hope to cooperate with a lot more friends for mutual added benefits.

2017 High quality Wear Resistant Submersible Sand - Free sample for Usb Rechargeable Air Pump,Portable Electric Air Pump Quick-fill Inflator Deflator Air Mattress Pump With Charging Function – Tiiec Detail:

For a result of ours specialty and repair consciousness, our business has won a very good name among the clients all around the globe for Free sample for Usb Rechargeable Air Pump,Portable Electric Air Pump Quick-fill Inflator Deflator Air Mattress Pump With Charging Function, You would not have any communication problem with us. We sincerely welcome prospects all around the globe to call us for business enterprise cooperation.

For a result of ours specialty and repair consciousness, our business has won a very good name among the clients all around the globe for Quick-fill Inflator Deflator Air Mattress Pump With Charging Function/ 3 Nozzles For Inflatables Tire Raft Bed Boat Pool Toy, Rechargeable Air Pump Inflatables Usb Boats 12v Automatic Plastic Pump For Airbed For Inflatables Tire Raft Bed Boat Pool Toy, Xg-668a Two Way Electric Charging Air Mattress Pump Quick-fill Ac Inflator Deflator With 3 Nozzles 110-120 Volt Black, Our items have national accreditation requirements for qualified, high quality products, affordable value, was welcomed by people today all over the world. Our goods will continue to enhance within the order and look forward to cooperation with you, Should any of these products be of interest to you, please letus know. We are going to be content to offer you a quotation up on receipt of your detailed needs.

Atlas Pump has preferred supplier to many of world’s most prestigious names in mining, cement, earth moving and construction, metal finishingand many other industries. We providing a wide choice of custom made parts of slurry pump, crusher, grinding machine, rubber and polyurethane to meet every customers’ needs. While providing these quality, long-wear life and cost effective replacement wear parts, we are available to offer a customer-friendly services. All of the custom wear parts can made to supplied samples or drawings.

We have been commitment to supply the competitive price ,excellent products and solutions high-quality, at the same time as fast delivery for 2017 High quality Wear Resistant Submersible Sand - Free sample for Usb Rechargeable Air Pump,Portable Electric Air Pump Quick-fill Inflator Deflator Air Mattress Pump With Charging Function – Tiiec , The product will supply to all over the world, such as: Zimbabwe, Suriname, Jordan, Welcome to visit our company, factory and our showroom where displays various products that will meet your expectation. Meanwhile, it is convenient to visit our website, and our sales staff will try their best to provide you the best service. Please contact us if you need more information. Our aim is to help customers realize their goals. We are making great efforts to achieve this win-win situation.

Lone Star Drills, a division of Little Beaver Inc. and manufacturer of efficient and portable drilling equipment, upgraded its LS200H and LS200H+ model drills with a Flomax 10 mud pump powered by an 8-horsepower Honda GX240 gas engine. The enhanced pump gives operators greater drilling speeds with approximately 40% more pressure and 30% more gallons of mud flow per minute over the previous pump setup.

“A mud pump is a crucial piece of equipment for ensuring mud rotary drilling efficiency,” said Joe Haynes, president of Little Beaver. “The feedback we’ve received from trials with this new setup has been outstanding. Crews were drilling noticeably faster than before because the system is providing a better flow of mud into the borehole, so we’ve made the new pump and engine a permanent fixture in our drill lineup.”

The new pump and engine come standard on the LS200H and LS200H+ hydraulic water well drills and are an optional upgrade for the LS100 and LS200 mechanical water well drills. A 10-horsepower Yanmar L100N diesel option is also available to power the Flomax on the LS200H and LS200H+.

The new Flomax 10 pump paired with the 8-horsepower engine provides 61 psi and 200 gallons of mud flow per minute, an upgrade of nearly 20 psi and an additional 50 gallons of flow per minute. The Flomax features a 2-by-2-inch inlet and outlet and incorporates tighter tolerances to handle the increased pressure from the larger engine.

Haynes said the increased pressure allows the new pump setup to not only quickly fill the borehole with a column of mud to remove cuttings more efficiently during drilling, but also handles thicker mud than the previous pump system. This provides crews with increased borehole stability as it replaces the dirt removed during drilling.

Pulled this out of the box, seen how it was constructed and the first thought that crossed my mind was what a rip off. Definitely not worth $300 for the box + $200 for handle + $300 for the pump. The thing is engineered so cheap and designed to force you to buy a pump that you really shouldn"t need, there are two stops that you have to take off to clean out the box when you are done, if they simply put wing nuts on these stops instead of screws you would have absolutely no need for the $300 pump. Even more laughable that they charge you an Extra $80 for the attachment to the pump to fill other items that you purchase from them. If this thing was $60-70 bucks then i could recommend buying it and I am sure every home owner would have one.. Too bad these people in their greed did not think of making money by selling a lot of these and opted to price gouge instead.

Created specifically for drilling equipment inspectors and others in the oil and gas industry, the Oil Rig Mud Pump Inspection app allows you to easily document the status and safety of your oil rigs using just a mobile device. Quickly resolve any damage or needed maintenance with photos and GPS locations and sync to the cloud for easy access. The app is completely customizable to fit your inspection needs and works even without an internet signal.Try Template

A kick is a well control problem in which the pressure found within the drilled rock is higher than the mud hydrostatic pressure acting on the borehole or rock face. When this occurs, the greater formation pressure has a tendency to force formation fluids into the wellbore. This forced fluid flow is called a kick. If the flow is successfully controlled, the kick is considered to have been killed. An uncontrolled kick that increases in severity may result in what is known as a “blowout.”

Yet another factor affecting kick severity is the “pressure differential” involved. Pressure differential is the difference between the formation fluid pressure and the mud hydrostatic pressure. If the formation pressure is much greater than the hydrostatic pressure, a large negative differential pressure exists. If this negative differential pressure is coupled with high permeability and high porosity, a severe kick may occur.

Another way of labeling kicks is by identifying the required mud weight increase necessary to control the well and kill a potential blowout. For example, if a kick required a 0.7-lbm/gal (84-kg/m3) mud weight increase to control the well, the kick could be termed a 0.7-lbm/gal (84-kg/m3) kick. It is interesting to note that an average kick requires approximately 0.5 lbm/gal (60 kg/m3), or less, mud weight increase.

Kicks occur as a result of formation pressure being greater than mud hydrostatic pressure, which causes fluids to flow from the formation into the wellbore. In almost all drilling operations, the operator attempts to maintain a hydrostatic pressure greater than formation pressure and, thus, prevent kicks; however, on occasion the formation will exceed the mud pressure and a kick will occur. Reasons for this imbalance explain the key causes of kicks:

Insufficient mud weight is the predominant cause of kicks. A permeable zone is drilled while using a mud weight that exerts less pressure than the formation pressure within the zone. Because the formation pressure exceeds the wellbore pressure, fluids begin to flow from the formation into the wellbore and the kick occurs.

These abnormal formation pressures are often associated with causes for kicks. Abnormal formation pressures are greater pressures than in normal conditions. In well control situations, formation pressures greater than normal are the biggest concern. Because a normal formation pressure is equal to a full column of native water, abnormally pressured formations exert more pressure than a full water column. If abnormally pressured formations are encountered while drilling with mud weights insufficient to control the zone, a potential kick situation has developed. Whether or not the kick occurs depends on the permeability and porosity of the rock. A number of abnormal pressure indicators can be used to estimate formation pressures so that kicks caused by insufficient mud weight are prevented (some are listed in Table 1).

An obvious solution to kicks caused by insufficient mud weights seems to be drilling with high mud weights; however, this is not always a viable solution. First, high mud weights may exceed the fracture mud weight of the formation and induce lost circulation. Second, mud weights in excess of the formation pressure may significantly reduce the penetration rates. Also, pipe sticking becomes a serious consideration when excessive mud weights are used. The best solution is to maintain a mud weight slightly greater than formation pressure until the mud weight begins to approach the fracture mud weight and, thus, requires an additional string of casing.

Improperly filling up of the hole during trips is another prominent cause of kicks. As the drillpipe is pulled out of the hole, the mud level falls because the pipe steel no longer displaces the mud. As the overall mud level decreases, the hole must be periodically filled up with mud to avoid reducing the hydrostatic pressure and, thereby, allowing a kick to occur.

Several methods can be used to fill up the hole, but each must be able to accurately measure the amount of mud required. It is not acceptable—under any condition—to allow a centrifugal pump to continuously fill up the hole from the suction pit because accurate mud-volume measurement with this sort of pump is impossible. The two acceptable methods most commonly used to maintain hole fill-up are the trip-tank method and the pump-stroke measurements method.

The trip-tank method has a calibration device that monitors the volume of mud entering the hole. The tank can be placed above the preventer to allow gravity to force mud into the annulus, or a centrifugal pump may pump mud into the annulus with the overflow returning to the trip tank. The advantages of the trip-tank method include that the hole remains full at all times, and an accurate measurement of the mud entering the hole is possible.

The other method of keeping a full hole—the pump-stroke measurement method—is to periodically fill up the hole with a positive-displacement pump. A flowline device can be installed with the positive-displacement pump to measure the pump strokes required to fill the hole. This device will automatically shut off the pump when the hole is full.

Gas-contaminated mud will occasionally cause a kick, although this is rare. The mud density reduction is usually caused by fluids from the core volume being cut and released into the mud system. As the gas is circulated to the surface, it expands and may reduce the overall hydrostatic pressure sufficient enough to allow a kick to occur.

Although the mud weight is cut severely at the surface, the hydrostatic pressure is not reduced significantly because most gas expansion occurs near the surface and not at the hole bottom.

Occasionally, kicks are caused by lost circulation. A decreased hydrostatic pressure occurs from a shorter mud column. When a kick occurs from lost circulation, the problem may become severe. A large volume of kick fluid may enter the hole before the rising mud level is observed at the surface. It is recommended that the hole be filled with some type of fluid to monitor fluid levels if lost circulation occurs.

An increase in flow rate leaving the well, while pumping at a constant rate, is a primary kick indicator. The increased flow rate is interpreted as the formation aiding the rig pumps by moving fluid up the annulus and forcing formation fluids into the wellbore.

If the pit volume is not changed as a result of surface-controlled actions, an increase indicates a kick is occurring. Fluids entering the wellbore displace an equal volume of mud at the flowline, resulting in pit gain.

When the rig pumps are not moving the mud, a continued flow from the well indicates a kick is in progress. An exception is when the mud in the drillpipe is considerably heavier than in the annulus, such as in the case of a slug.

A pump pressure change may indicate a kick. Initial fluid entry into the borehole may cause the mud to flocculate and temporarily increase the pump pressure. As the flow continues, the low-density influx will displace heavier drilling fluids, and the pump pressure may begin to decrease. As the fluid in the annulus becomes less dense, the mud in the drillpipe tends to fall and pump speed may increase.

Other drilling problems may also exhibit these signs. A hole in the pipe, called a “washout,” will cause pump pressure to decrease. A twist-off of the drillstring will give the same signs. It is proper procedure, however, to check for a kick if these signs are observed.

When the drillstring is pulled out of the hole, the mud level should decrease by a volume equivalent to the removed steel. If the hole does not require the calculated volume of mud to bring the mud level back to the surface, it is assumed a kick fluid has entered the hole and partially filled the displacement volume of the drillstring. Even though gas or salt water may have entered the hole, the well may not flow until enough fluid has entered to reduce the hydrostatic pressure below the formation pressure.

Drilling fluid provides a buoyant effect to the drillstring and reduces the actual pipe weight supported by the derrick. Heavier muds have a greater buoyant force than less dense muds. When a kick occurs, and low-density formation fluids begin to enter the borehole, the buoyant force of the mud system is reduced, and the string weight observed at the surface begins to increase.

Fortunately, the lower mud weights from the cuttings effect are found near the surface (generally because of gas expansion), and do not appreciably reduce mud density throughout the hole. Table 3 shows that gas cutting has a very small effect on bottomhole hydrostatic pressure.

An important point to remember about gas cutting is that, if the well did not kick within the time required to drill the gas zone and circulate the gas to the surface, only a small possibility exists that it will kick. Generally, gas cutting indicates that a formation has been drilled that contains gas. It does not mean that the mud weight must be increased.

The MWD tool enables monitoring of the acoustic properties of the annulus for early gas-influx detection. Pressure pulses generated by the MWD pulser are recorded and compared at the standpipe and the top of the annulus. Full-scale testing has shown that the presence of free gas in the annulus is detected by amplitude attenuation and phase delay between the two signals. For water-based mud systems, this technique has demonstrated the capacity to consistently detect gas influxes within minutes before significant expansion occurs. Further development is currently under way to improve the system’s capability to detect gas influxes in oil-based mud.

Some MWD tools feature kick detection through ultrasonic sensors. In these systems, an ultrasonic transducer emits a signal that is reflected off the formation and back to the sensor. Small quantities of free gas significantly alter the acoustic impedance of the mud. Automatic monitoring of these signals permits detection of gas in the annulus. It should be noted that these devices only detect the presence of gas at or below the MWD tool.

where gi = influx gradient, psi/ft; gmdp = mud gradient in drillpipe, psi/ft; and hi = influx height, ft. The influx gradient can be evaluated using the guidelines in Table 1.

It is necessary to calculate the mud weight needed to balance bottomhole formation pressure. “Kill-weight mud” is the amount of mud necessary to exactly balance formation pressure. It will be later shown that it is safer to use the exact required mud weight without variation

Because the drillpipe pressure has been defined as a bottomhole pressure gauge, the psidp can be used to calculate the mud weight necessary to kill the well. The kill mud formula follows:

Because the casing pressure does not appear in Eq. 2, a high casing pressure does not necessarily indicate a high kill-weight mud. The same is true for pit gain because it does not appear in Eq. 2. Example 1 uses the kill-weight mud formula.

Pumps tend to be one of the biggest energy consumers in industrial operations. Pump motors, specifically, require a lot of energy. For instance, a 2500 HP triplex pump used for frac jobs can consume almost 2000 kW of power, meaning a full day of fracking can cost several thousand dollars in energy costs alone!

So, naturally, operators should want to maximize energy efficiency to get the most for their money. Even a 1% improvement in efficiency can decrease annual pumping costs by tens of thousands of dollars. The payoff is worth the effort. And if you want to remotely control your pumps, you want to keep efficiency in mind.

In this post, we’ll point you in the right direction and discuss all things related to pump efficiency. We’ll conclude with several tips for how you can maintain pumping efficiency and keep your energy costs down as much as possible.

In simple terms, pump efficiency refers to the ratio of power out to power in. It’s the mechanical power input at the pump shaft, measured in horsepower (HP), compared to the hydraulic power of the liquid output, also measured in HP. For instance, if a pump requires 1000 HP to operate and produces 800 HP of hydraulic power, it would have an efficiency of 80%.

Remember: pumps have to be driven by something, i.e., an electric or diesel motor. True pump system efficiency needs to factor in the efficiency of both the motor AND the pump.

Consequently, we need to think about how electrical power (when using electric motors) or heat power (when using combustion engines) converts into liquid power to really understand pump efficiency.

Good pump efficiency depends, of course, on pump type and size. High-quality pumps that are well-maintained can achieve efficiencies of 90% or higher, while smaller pumps tend to be less efficient. In general, if you take good care of your pumps, you should be able to achieve 70-90% pump efficiency.

Now that we have a better understanding of the pump efficiency metric, let’s talk about how to calculate it. The mechanical power of the pump, or the input power, is a property of the pump itself and will be documented during the pump setup. The output power, or hydraulic power, is calculated as the liquid flow rate multiplied by the "total head" of the system.

IMPORTANT: to calculate true head, you also need to factor in the work the pump does to move fluid from the source. For example, if the source water is below the pump, you need to account for the extra work the pump puts in to draw source water upwards.

*Note - this calculation assumes the pump inlet is not pressurized and that friction losses are minimal. If the pump experiences a non-zero suction pressure, or if there is significant friction caused by the distance or material of the pipe, these should be factored in as well.

You"ll notice that the elevation head is minimal compared to the discharge pressure, and has minimal effect on the efficiency of the pump. As the elevation change increases or the discharge pressure decreases, however, elevation change will have a greater impact on total head.

Obviously, that’s a fair amount of math to get at the pump efficiency, considering all of the units conversions that need to be done. To avoid doing these calculations manually, feel free to use our simple pump efficiency calculator.

Our calculations use static variables (pump-rated horsepower and water source elevation) and dynamic variables (discharge flow and pressure). To determine pump efficiency, we need to measure the static variables only once, unless they change.

If you want to measure the true efficiency of your pump, taking energy consumption into account, you could add an electrical meter. Your meter should consist of a current transducer and voltage monitor (if using DC) for electrical motors or a fuel gauge for combustion. This would give you a true understanding of how pump efficiency affects energy consumption, and ultimately your bank account.

Up until this point, we’ve covered the ins and outs of how to determine pump efficiency. We’re now ready for the exciting stuff - how to improve pump efficiency!

One of the easiest ways to improve pump efficiency is to actually monitor pumps for signs of efficiency loss! If you monitor flow rate and discharge (output power) along with motor current or fuel consumption, you’ll notice efficiency losses as soon as they occur. Simply having pump efficiency information on hand empowers you to take action.

Another way to increase efficiency is to keep pumps well-maintained. Efficiency losses mostly come from mechanical defects in pumps, e.g., friction, leakages, and component failures. You can mitigate these issues through regular maintenance that keeps parts in working order and reveals impending failures. Of course, if you are continuously monitoring your pumps for efficiency drops, you’ll know exactly when maintenance is due.

You can also improve pump efficiency by keeping pumps lubricated at all times. Lubrication is the enemy of friction, which is the enemy of efficiency (“the enemy of my enemy is my friend…”).

A fourth way to enhance pump efficiency is to ensure your pumps and piping are sized properly for your infrastructure. Although we’re bringing this up last, it’s really the first step in any pumping operation. If your pumps and piping don’t match, no amount of lubricant or maintenance will help.

In this post, we’ve given you the full rundown when it comes to calculating and improving pump efficiency. You can now calculate, measure, and improve pump efficiency, potentially saving your business thousands of dollars annually on energy costs.

For those just getting started with pump optimization, we offer purpose-built, prepackaged solutions that will have you monitoring pump efficiency in minutes, even in hazardous environments.

When you"re seeking the field flexibility to complete your drilling faster, easier and safer, count on Geoprobe® drill rigs engineered for versatility and manufactured for reliability. Industry leaders depend on our ongoing commitment to innovation and industry-leading customer support to advance their business ahead of the competition. Digital readouts providing instant feedback, enhanced safety features, easy operation, and availability of training options mean veteran drillers find their jobs simplified while new drillers build confidence, making them productive as they"re quickly coming up the learning curve.

Whether you’re facing consolidated materials, glacial till, or backfill rubble, quickly complete complex holes to greater depths with the powerful GV5 50K sonic head on our line of sonic drill rigs. Engineered by Geoprobe® to advance up-to 12-inch tooling, the GV5 produces torque required to maintain rotation in tight formations – all backed by a 2-year warranty.

Combine geotechnical augering and high-speed rotary with advanced direct push capability to offer additional services to your customers, quickly going from coring rock to pushing CPT - all in one drill rig.

With the necessary tophead rotation speed, head feed speed, and plenty of mud pump options to get the job done, complete your water well drilling, geothermal drilling, and cathodic protection drilling jobs with a single, compact water well drill.

Outfit as down the hole drill or mud drill with the power of 28.5-foot stroke, 40,000 lb pullback, and 8,000 ft-lb torque to handle deeper wells along with weight of steel casing.