stainless steel pressure safety valve supplier

The No. 210 & 213 series MGM Relief Valves are designed for the protection of piping and equipment from over-pressure conditions. They are available for any predetermined pressure from 50 to 1500 psig and will automatically reseat after discharge. Valves in this series feature American Standard 1/8” or 1/4” male and female pipe threads to mate with new or existing fittings or equipment.

Other features of the MGM No. 210 & 213 series relief valves are seat discs made of Viton which provide a “bubble tight “ seal. Pipe Away Adapters are available for the direct connection of vent piping when required. Outage tubes (dip tubes) have been incorporated into the inlet end of the No. 213 series valves.

NOTE: Each relief mechanism is set to the required pressure and sealed before leaving the MGM factory. When ordering the customer should state the model number and pressure desired.

Stra-Val designs and manufactures its own line of Stainless Steel Relief Valves. If you are looking for high quality performing Adjustable Pressure Relief Valves, you have come to the right place! Our Stainless Steel Relief Valves are manufactured out of stainless steel(316 or 303), depending on your requirements.

We have a wide selection of Relief Valves, you can choose from. We strive to provide you with HIGH QUALITY products and UNBEATABLE prices! You can count on Straval, to satisfy your needs!

For corrosion resistance in wet conditions and harsh environments, these valves have a 303 stainless steel body. They spring fully open at the set pressure and remain open until the system pressure is restored below the set pressure. All meet ASME Code Section VIII for use with air and inert gas pressure vessels. Valves have a vented relief port to exhaust discharge directly.

With a 316 stainless steel body for exceptional corrosion resistance, these valves are often used in wet conditions and harsh environments. They spring fully open at the set pressure and remain open until the system pressure is restored below the set pressure. All meet ASME Code Section VIII for use with air and inert gas pressure vessels. Attach a drain line to the threaded relief port for remote discharge.

To Order: Please specify medium (air or inert gas) and set pressure in 1 psi increments (from 150 to 2,700 psi for valves with 1/2 or 1 inlet pipe size, or 150 to 2,269 psi for valves with 3/4 inlet pipe size).

Design a valve specifically for your process media and set pressure. Choose from a valve for air, inert gas, water, hydraulic oil, fuel oil, gasoline, or diesel fuel and a set pressure from 150 to 3,300 psi. These valves begin opening at the set pressure and fully open at about 10% over the set pressure. They begin closing as pressure drops and fully close when the system pressure is restored below the set pressure. Body is 316 stainless steel for exceptional corrosion resistance.

Withstand more than six times the inlet pressure of standard pressure-regulating valves. These valves automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range. Valves have a 303 stainless steel body for corrosion resistance in harsh environments.

Often used in wet conditions and harsh environments, these valves have a 316 stainless steel body for excellent corrosion resistance. They automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range.

To maintain contaminant-free standards in clean room environments, these valves come cleaned and bagged to Fed. Std. Class 100 and ISO Class 5 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection. They automatically reduce a high, variable inlet pressure to a lower, stable output pressure. Adjust the outlet pressure within the range. Valves are no-bleed style, so they keep process media contained within the valve.

Often used on dispensers, humidifiers, and fountains, these valves have a 316 stainless steel body that can stand up to deionized water and corrosive conditions. They automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range. Valves have a low-profile body to fit in tight spots. All have a gauge port.

Change outlet pressure without using a gauge—turn the dial to adjust the outlet pressure in 5 or 10 psi increments. These valves automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. They also have an internal strainer to trap debris. Union fittings on both ends of the valves disassemble for easy valve installation and removal. All of these valves meet Canadian safety standards for pressure-reducing valves. Some also meet American and international plumbing safety and performance standards.

To regulate inlet pressures up to 6,000 psi in wet conditions and harsh environments, these valves have a 316 stainless steel body for exceptional corrosion resistance. They automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range. Valves have threads below the adjustment knob and come with a panel-mount nut. All have two gauge ports. They are no-bleed style, so they keep the process gases contained in the valve.

Commonly used for oxygen service and other high-purity applications, these valves come cleaned and bagged to prevent contamination. All automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range. Valves have threads below the adjustment knob and come with a panel-mount nut. They can also be surface mounted. All have two gauge ports. Body is 316 stainless steel for exceptional corrosion resistance. Valves are no-bleed style, so they keep process gases contained in the valve.

Maintain contaminant-free standards in clean room environments. These valves come cleaned and bagged to Fed. Spec. Class 100 and ISO Class 5 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection. They automatically reduce a high, variable inlet pressure to a lower, stable output pressure. Valves have threads below the adjustment knob and come with a panel-mount nut. Adjust the outlet pressure within the range.

Regulate steam pressure in wet environments and harsh conditions with these valves that have a 316 stainless steel body for exceptional corrosion resistance. They automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range.

Regulate air, gas, and liquid pressure on food, beverage, and pharmaceutical lines with these valves—they’re 3-A certified to meet sanitary design standards. Attach them to your line to reduce a high, variable inlet pressure to a lower, stable outlet pressure.

Twist the T-handle on top of the valve to adjust the outlet pressure. When the valve is closed, a seal on the outlet prevents leaks and helps maintain consistent pressure. These valves meet ANSI/FCI 70-2 Class III, which means a maximum of 0.1% of fluid, gas, or air can escape while they are fully closed. The spring and valve mechanism are sealed behind the diaphragm, so contaminants can’t enter. Both the diaphragm and seals hold up to water, detergents, and chemicals. They’re also FDA compliant for direct contact with food.

Made of 316 stainless steel, these valves won’t corrode from frequent washdowns with harsh cleaners. They connect to your line with quick-clamp sanitary fittings, also known as tri-clamp connections, which are easier to remove and sanitize than threaded connections. The polished interior is extremely smooth, so there’s nowhere for bacteria to hide. They’re also self-draining, so liquids drain completely and don’t contaminate your line. Keep these valves open during clean-in-place (CIP) cycles with a locking pin.

Designed to reduce contaminants in high-purity applications using hydrogen and methane gas, these valves have a stainless steel and brass body with a smooth finish to reduce dust collection and internal components designed to protect the seal and diaphragm from contamination. They’re often used in research sample systems, emission monitoring systems, and chromatography. Valves automatically reduce a high inlet pressure from compressed gas tanks to a lower, stable outlet pressure. All have Compressed Gas Association (CGA) numbered inlet fittings for secure connections to compressed gas tanks. Choose a valve with the same CGA number as your tank and other system components. Outlet fittings are Swagelok® for a leak-free seal around hard metal tubing in high-pressure lines. Also known as instrumentation fittings, Swagelok® fittings are compatible with Parker A-Lok, Gyrolok, Bilok, and Tylok fittings. Valves come with a gauge to monitor outlet pressure and a gauge to monitor inlet pressure from the tank.

Choose a valve with a maximum outlet pressure that’s approximately twice your application’s normal operating pressure. Your operating pressure should never exceed 75% of the valve’s maximum outlet pressure.

Single-stage valves reduce pressure in one step, which causes the outlet pressure to fluctuate slightly as you empty the tank. They’re best for applications where a constant outlet pressure isn’t critical.

Two-stage valves progressively reduce pressure over two steps for more consistent outlet pressure at all times. They’re often used in applications that require a constant outlet pressure regardless of the tank level.

Designed to meet 3-A sanitary standards, these valves regulate liquid, gas, and air pressure in hygienic zones of food and beverage plants. They’re often used at the end of pipelines on processing and sanitizing equipment. Made of 316 stainless steel, they won"t corrode from frequent washdowns with harsh cleaners. With an extremely smooth interior that self-drains, bacteria won"t have time or space to grow. The spring and internal valve mechanisms are sealed off behind the diaphragm, which also prevents contamination. They connect with quick-clamp fittings, so disassembling to clean your line takes little time.

These valves obstruct flow to maintain sufficient operating pressure in your system. If the system pressure exceeds the set pressure, they exhaust through the outlet. They meet ANSI/FCI 70-2 Class III standards for shut-off valves, meaning a maximum of 0.1% of fluid, gas, or air will escape through the outlet when they’re closed. An integrated T-handle lets you set the outlet pressure without additional tools. The diaphragm and seal resist repeated exposure to water, and they’re FDA compliant for direct contact with food.

To set the pressure, unscrew the cap and turn the adjustment screw. Valves begin opening at the set pressure and fully open at about 10% over the set pressure. They begin closing as pressure drops and fully close when the system pressure is restored below the set pressure.

An external nut lets you adjust the pressure without disassembling the valve. These valves begin opening at the set pressure and fully open at about 10% over the set pressure. They begin closing as pressure drops and fully close when the system pressure is restored below the set pressure.

... designs. Its all-stainless-steel construction and high-quality metal-to-metal seat result in a repeatable cracking pressure and a long life. Each valve is 100% tested to ensure that all ...

It"s a Safety valve in according with Directives ATEX 20K/34/EU. Technical Norm Fire Prevention 41/256 31/10/2019. d.P.R. 10/520 19/03/1955 and subsequent amendments.

V651 Series safety relief valves are produced as safety and relief type. Safety valves are pressure relief elements used to evacuate excessive pressure ...

Parker"s cartridge safety relief valves (CSRV) are designed to offer the highest level of protection while maintaining easy serviceability. The CSRV was designed from the existing Parker ...

2½” MEGA SUPERVENTIX™ threaded safety relief valve is designed to protect tanks against accidental overpressure and excessive vacuum. With a smart compact design, the 2½” BSP MEGA SUPERVENTIX™ SRV has ...

Manufacturer of standard & custom steel & stainless steel safety relief valves. Stainless steel safety relief valves feature stainless steel semi-nozzle trim, inlet & outlet flange, bolted bonnet design, enclosed spring, lapped seats to optical flatness, dual control rings which allows adjustability for precision opening with minimum pre-open or simmer & exact blow down control, heavy duty lift lever assembly & factory-sealed adjustments to prevent tampering or dis-assembly. Stainless steel safety relief valves are suitable for steam, air & non-hazardous gas service. Applications include steam boilers & generators, pressure reducing stations, reciprocating or rotary air or gas compressors & pressure vessels including tanks, receivers, intercoolers, oil-gas separators & lines.

Recommended for all cold water system installations - to protect against damage to piping and pressure tanks. PRV"s are set at 75 PSI or 100 PSI. PRV"s have a plus/minus 15% setting accuracy

Note: Merrill pressure relief valves may not reseat themselves after pressure relief. Manual disassembly and reseating of the valve may be required. Repeated opening of a pressure relief valve is beyond intended use and voids warranty

*Note: ALL PRV valves are field adjustable - by removing the cap and turning internal disk down to increase pressure. Field adjustment of valve voids warranty.

Warning: ALL PRV, SSPRV, and PRVNL valves must be set a minimum of 15 PSI above the typical high of the water system pressure, so valve chatter or rapid open and close will not occur. Valve chatter can cause the failure of the valve and voids warranty.

Providing you the best range of cast steel safety relief valves, open bonnet safety relief valve, stainless steel safety relief valve, flange end pressure relief valves, safety relief valve and pressure safety valve with effective & timely delivery.

Valve Check Inc. is a manufacture of high-quality check valves offered in a variety of sizes ranging from 1/8, 1/4, 1/2, 3/4, 1 inch though 2 inch and up to 4" NPT. Configurations are offered in Male x Male, Male x Female, Female x Male, and Female x Female.

Valve Check specializes in manufacturing the lowest pressure drop check valves and offers the highest flow check valves of any manufacturer. Pressures range from low pressure .5 psi to 500 psi high pressure check valves.

Relief and safety Valves are used in high pressure systems to control the pressure and keep balance of the system. The different between safety valves and relief valves is that the safety valves fully open or close under a certain pressure while the relief valves can open in proportion to the pressure in front of them. The safety and pressure relief valves are used automatically. They both operate under similar conditions. When the pressure builds up in a system, it has to be managed by releasing the material to flow through. These valves have a threshold pressure at which they open. The consolidated safety and safety relief valves comprise of a bonnet vent and bellow with springs.

The springs are set up for the threshold pressure and when the pressure exceeds the threshold, the spring is pushed into the bonnet vent and the bellow opens the valve. The Safety Relief Valves can be open and shut valves. They either open or shut off at any given pressure. This is mostly for the safety of an application not to explode under high pressure. The Pressure Relief Valve on the other hand releases the material after the threshold pressure, but not fully. If the pressure is slightly higher the threshold, then the valve opens slightly. If the pressure is very high above the threshold, it opens wider. It also functions in the same manner when the pressure drops down. The valve closes in proportion to the pressure. The safety valve shuts down at once only when the pressure is below the threshold.

Ready Stock of ASTM A351 CF8M Spring Loaded Safety Valve in wide range of Sizes, Stainless Steel Air Compressor Pressure Relief Valve Manufacturers In India

Relief Valves are designed to control pressure in a system While Safety Valves are used for controlling the pressure in a system they release pressure immediately in the event of an emergency or system failure

The Setpoint of relief valve is usually set at 10 Percent above working pressure limit while safety valve is usually set at 3% above working pressure limit.

If you are operating systems that can only be off for short periods of time, it is sensible to keep a spare valve to swap over and then the removed valve can be inspected and recertified.