gag safety valve pricelist

We, D Chel Oil & Gas Products OPC Pvt. Ltd. a stockist, supplier & exporter, we maintain close links to diverse vendors. The company is vertically consolidated holding with high sell sufficiency in different types of Valves manufacturers i.e. industrial raw material in all size, grades, and forms, which enables.

This range of spring loaded conventional Pressure Relief Valves is for installation of any SECTION VIII application and are available from pressure range of 0.3 Bar to 414 Bar and for pressure ratings up to 2500#. Sizes from 1" D 2" to 8" T 12" in different material of construction depending - Safety Valve & Control Valve Division

Main Features Flanged, Spring loaded, Direct acting, Full nozzle pressure Media : Gas, Steam and Liquid. Set pressure range : From 0.3barto 414 bar. Temperature range : From -201 o Cto715oC. Materials : Carbon Steel, Alloy Steel, Hastelloy, Monel and other materials upon Options : Bellows, Flushing nozzle, Lifting lever, Test gag, Finned bonnet, Limit switch, Resilient or Hardened seat. Sizes/Pressure Classes Size inlet&outlet: from NPS1 to NPS 8 & from NPS 2 to NPS12 Rating: up to ASME 2500. Special solution ASME 4500 and up Design Codes & Product Standards 521, API 526, API 527, ASME...

INTRODUCTORY NOTES COLD DIFFERENTIAL TEST PRESSURE TOLERANCE The tolerances on the cold differential test pressure are over 21 bar ±1%orO, 7 bar whichever is greater MINIMUM COLD DIFFERENTIAL TEST PRESSURE (SPRING SETTING) The minimum cold differential test pressure is shown in the following table. For conventional valves with special construction, the minimum cold differential test pressure can be reduced to BALANCED PRESSURE RELIEF VALVES (with bellows or Series SV-100 valves can be provided with balancing and separation bellows. This accessory is used when: a) There is a variable...

Tungsten steel spring and Materials to table, page 10 Materials to table, page 10 Plain lever (no stuffing box) Packed lever (stuffing box) Heating jacket O-ring (soft seated disc) Finned bonnet extension (high temperature duty) Valve seat injection nozzles Special trim for liquids. - Valve construction of materials as per list, page 10 - For utilization in the temperature range 232,5- 426°C - Tungsten steel valve spring - balancing bellows packed lever and test gag supplied. * Recommended spare parts Conventional Valve Bellows Valve - Safety Valve & Control Valve Division

Soft, seated disc (viton; teflon; kalrez) for low pressures Special trim for liquids(series 10O-SV/LIQ) Cap with packed or plain lever Cap with test gag - Safety Valve & Control Valve Division

Type "R" counter weighted lever Type"L" counter weighted lever jacket connection Jacketed Body Valves Series SV-100 BODY VALVE HEATING JACKET (Jacket limiting pressure: 10kg/cm2 limiting temperature 18&C.) - Safety Valve & Control Valve Division

Nozzle-disc seats manufactured by UKL AST are of the metal They can be supplied hardened (with stellite or made in 17- 4PH) or resilient (with o-ring). The most frequent cases in which these constructions are requested are: 1) hardened when the media is dirty, may crystallize 2) hardened for medium and high pressure depending on the temperature, see following diagram 3) resilient when requested by client UKL AST will suggest the best solution for each operating - Safety Valve & Control Valve Division

The dimensions and the weights are approximate, will not assume any liability for discrepancies between actual dimensions and weights and those shown in this table. Approx. weight - Safety Valve & Control Valve Division

DEFINITIONS (abstract from EN ISO 4126-1) The actual travel of the valve disc away from the closed position. Flow area The minimum cross-sectional flow area (butnotthe curtain area) between inlet and seat which is used to calculate the theoretical flowcapacity, with no deduction for any obstruction. The value of actual flowing capacity (from tests) divided by the theoretical flowing capacity (from calculation). Built-up backpressure The pressure existing atthe outlet of a safety valve caused by flow through the valve and the discharge system. Superimposed back pressure The pressure existing...

Our range of valves also includes special service valves which are used for special purposes like releasing excess pressure.Our service valves are available at the most reasonable prices. Please supply the following information for prompt order processing:

Our safety relief valve is fitted in vessels to prevent an undue rise in pressure.Whenever the vacuum is build, the safety relief valve gets actuated and there is a rapid opening or pop up action to release the pressure. Used in various industries, our safety valve is available in sizes to suit the requirements of our clients.

CAPRO Self-actuating, Internally pilot & piston operated, Globe type, Full lift, Spring & diaphragm actuated, Pressure reducing/regulating valve, also known as Down-Stream Pressure Control Valve.

CAPRO internally pilot & piston operated pressure reducing valves are very compact in design & versatile type for accurate regulation with the widest possible range of flow

The constant outlet pressure (Down stream pressure) is accurately maintained right up to maximum rated discharge capacity of the valve and is unaffected by changes in inlet pressure or flow rate

Our ranges of breather valves are designed to prevent losses, by controlling the evaporation of volatile liquid from the sponge tanks.Further, they allow breathing when the pressure in the tanks exceeds a pre-defined value. Used in diverse industries like petroleum, chemical and general process industries, our range of breather valves are available with the following

Leakage:Breather valve with resilient seating will have a maximum leakage of 45 nlph at 90% set pressure. Metal to metal seats will have a slight higher leakage rate.