gagging tool for boiler safety valve quotation
Before attempting to adjust the safety valves of any boiler,its essential to verify the accuracy of the boiler pressure gauge,safety valves must be set at a pressure not exceeding 3% above the approved working pressure each safety valve is adjusted independently.
You will hear a hissing sound, this is the floating condition of the valve and subsequently the valve will lift. if the valve lifts before the set pressure is achieved tighten the compression nut. if the valve fails to lift at the set pressure loosen the compression nut, maintain the boiler pressure constant while adjusting, reduce boiler pressure, remove gagging tool and fit to other valve for setting.
After both valves are set, remove the gagging tool and fire the boiler to maximum capacity. note full flow of waste steam from waste steam pipe. note pressure on gauge, the pressure should not exceed 10% of set pressure. after completion refit caps, cotter, locks and easing gear.
Test Gag is a bolt used for the spindle block of the pressure relief valve (PRV) to allow the PRV to be closed during the pressure test. The bolt should be tightened when the system has 80% of the pressure used. test (test pressure) to ensure that the PRV is closed at the test Pressure:
Although the number of relief valves provided must have a rated capacity equal to "all the steam the boiler can generate", most boilers can generate 10-20% more steam than the relief valves can relieve anyhow, if firing the best avaialable fuel at lowest possible excess air , with all mills and burners in service.
Warning: All pipe plugs must be blocked or anchored adequately against a force equal to the head pressure times the cross-sectional area of the pipe. Debris or protrusions in the pipeline can damage a seal or rupture inflatable plugs. NEVER use an inflatable plug when its failure could cause injury or catastrophic damage or as the only means of protection for personnel working downstream. NEVER use a test pressure greater than the capacity of the weakest pipe or component in the system. Actual conditions vary so user must accept full risk and responsibility for the selection and use of any product. Please review our Warranty, Terms and Conditions.
Note 1: Mechanical and Molded Rubber Plugs are generally used for testing because fabricated Multi-Flex® style plugs may allow some seepage unless customized for a positive seal.
Boiler safety valve setting procedure is given in this article. To make the content easier to understand and also to make reader to understand as how this important activity is done.
As an engineer onboard you will be required to set the safety valve after each boiler survey. It is a process which needs precision and skill also. Let’s check the stepwise details of the procedure you need to follow while setting the valve.
2) Boiler is ready to be fired. Make sure that the steam blow off line after the safety valve, have a drain and it should be unclogged and should have free passage.
7) Screw down the compression nut little bit more than the previous distance. If you don’t have previous reading, then it will require little bit more attempts before you can actually set the valve.
8) Now let’s say you have to set valve at 9 bar. So, raise the pressure slowly. Just before the 9 bar, like 8.8 or 8.9, you will start seeing little bit of steam coming out of the safety valve.
Note: If you safety valve lifts at 10 bar instead of 9, then don’t try to set it down at the same time. Lower the pressure to 7 bar or something and then adjust the compression nut and then again raise the pressure to 9 bar. Otherwise you get all the wrong adjustment.
14) After both valves are set, they usually have some difference like 0.3 bar. This is not intentional and comes due to the fact that precise and similar adjust of both the valves is not same.
The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.
DEAR FRNDS, IF WE DO GAGING AT ANY PRESSURE IT IS WRONG. I HAVE RECENTLY GONE THROUGH A TRAINING PROGRAM ON SAFETY VALVE .IT RECOMMENDS THAT GAGING TO BE DONE AT 70% PRESSURE.
Never, ever gage a safety valve while under any pressure. Serious injury can occur. The safeties are gaged only if you are doing a hydro over the set pressures on the valves. This is only accomplished after major repairs. The NBIC recommends going to 80% of the lowest safety valve setting for a tightness hydro or after the completion of routine repairs.
I"m not sure precisely what the API has to do with boiler operation but whatever. You only gag a safety if you"r squeezing the vessel to 1 1/2 times the working pressure. This is only done after construction or major repair. The rest of the time you squeeze the boiler to working pressure and if you"r careful not to go over that you don"t need to gag the safety valves. You most certainly would never operate the boiler with gags on the safety valves.
If you are human user receiving this message, we can add your IP address to a set of IPs that can access FederalRegister.gov & eCFR.gov; complete the CAPTCHA (bot test) below and click "Request Access". This should only be necessary once for each IP address you access the site from.
If you want to request a wider IP range, first request access for your current IP, and then use the "Site Feedback" button found in the lower left-hand side to make the request.
Distributor of hydraulic press safety, quick opening safety, rotary and safety valves. Amerigear®, Boston Gear®, Carlisle®, DeMag®, Desch® and IMI Norgren®, pneumatic, double action, quick release and flow control valves also provided. Repair and preventative maintenance services are offered. Value added services such as custom barcoding, CAD capabilities, OEM assembly, plant surveys and third party logistics are also available. Serves the metal processing, metal service center, paper mill and paper converting, canning, grinding, commercial laundry, marine, oil and gas and material handling industries. Vendor managed inventory (VMI) programs available. Kanban delivery.